Caple ZC621 User manual

Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk
Wall chimney hood instruction manual
ZC621 / ZC921
ZC921-621 - Instruction Manual.indd 1 20/11/2015 10:32

Instruction manual ZC621 / ZC921
2
Please keep this instruction manual for future reference
CONTENTS
Introduction 3
Safety precautions 4
Environmental protection 6
Instructions for installation 7
Operating instructions 10
Care and maintenance 11
Troubleshooting 14
Guarantee and servicing 14
Caple Service contact details 16
ZC921-621 - Instruction Manual.indd 2 20/11/2015 10:32

Instruction manual ZC621 / ZC921
3
Please keep this instruction manual for future reference
INTRODUCTION
Thank you for choosing this Caple extractor hood.
To ensure that you get the best results from your new extractor, we strongly suggest that
you read this instruction manual thoroughly before use. If treated with care, your Caple
extractor should give you years of trouble-free use.
To register ownership, please ensure you complete and return the guarantee card
supplied with the appliance or visit www.caple.co.uk and register here.
This instruction manual is designed to provide you with all the required information
related to the installation, use and maintenance of the appliance.
This hood is designed to extract unpleasant odours from the kitchen; it is not intended
to extract steam. In order to operate the unit correctly and safely, please read this
instruction manual carefully before installation and use.
The cooker hood uses high quality materials and is made with a streamlined design.
Equipped with an electric motor and centrifugal fan, it provides strong extraction with
low noise. It also features non-stick grease filters and an easy installation.
IMPORTANT
This appliance must only be used for the purpose it is intended. Other types of use are
not permitted and may prove dangerous. Caple will not be held liable for any damage
caused by the incorrect use of the appliance.
Do not use any accessories or attachments not recommended by Caple as this may result
in fire, electric shock or injury.
To protect against fire, electrical shock and injury to persons, do not immerse cords or
plugs in water or any other liquid.
Never touch the appliance with wet or damp hands.
Never pull the power cable as you could damage it.
If the appliance is faulty, do not attempt to repair it. Isolate it from the mains electric
supply and contact Caple Service either by phone [phone] or email
[email protected].
ZC921-621 - Instruction Manual.indd 3 20/11/2015 10:32

Instruction manual ZC621 / ZC921
4
Please keep this instruction manual for future reference
Keep all packaging (including plastic bags, polystyrene foam etc) out of the reach and
away from children.
Do not rest large or unstable objects on any part of the appliance.
IMPORTANT
Caple cannot be held responsible for injuries or losses caused by incorrect use or
installation of this product. Please note that Caple reserve the right to invalidate the
guarantee supplied with this product following incorrect installation or misuse of the
appliance. Under no circumstances should any external covers be removed for servicing
or maintenance except by suitably qualified personnel.
SAFETY PRECAUTIONS
- Never let children operate the machine.
- The cooker hood is for home use only, not suitable for barbecuing, restaurants or other
commercial purposes.
- The cooker hood and its filter should be cleaned regularly in order to keep in good
working condition.
- Clean the cooker hood according to the instruction manual to reduce the risk of fire.
- When using a gas hob, do not leave naked flames under the extractor.
- Before connecting this appliance check that the power supply cord is not damaged.
- If the room where the hood is to be used contains a fuel burning appliance such as a
central heating boiler then its flue must be of the sealed or balanced flue type. If other
types of flue or appliances are fitted ensure that there is an adequate supply of air to
the room.
- The air must not be discharged into a flue that is used for exhausting fumes from
appliances burning gas or other fuels.
- Regulations concerning the discharge of air have to be conformed to.
- Do not flambé under the cooker hood.
- Never leave frying pans unattended during use as over-heated fats and oils may catch
fire.
- To ensure the best performance, we recommend switching on the extractor 15 minutes
before cooking and leave it running 15 minutes after. This will ensure that the air in the
kitchen is being circulated before cooking commences and the air is being cleaned after
cooking has finished.
- The performance of your extractor will vary depending on a number of factors. These
include type of extraction, room volume, length of ducting, ventilation available and
the cleanliness of the filters.
ZC921-621 - Instruction Manual.indd 4 20/11/2015 10:32

Instruction manual ZC621 / ZC921
5
Please keep this instruction manual for future reference
- This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Cleaning and user maintenance must not be made by children without supervision.
- Never immerse the appliance in water.
- This product is not designed for commercial use, it is a household appliance only. It is
not intended to be used in:
- Staff kitchen areas in shops, offices and other working environments,
- Bed and breakfast type environments,
- By clients in hotels, motels and other residential type environments.
- To avoid all risk, if the power cable is damaged, it must only be replaced by a Caple
appointed engineer.
- Appliances can be used by persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved.
- Children must not play with this appliance.
- When not in use and before cleaning, always isolate the appliance from the electrical
supply.
ELECTRICAL SHOCK HAZARD
- Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably
qualified engineer.
- Failure to follow these instructions can result in death, fire, or electrical shock.
- This appliance must be connected to the mains by a competent person. We
recommend that the appliance is connected by a qualified electrician who is a member
of the N.I.C.E.I.C who will comply with the I.E.E and local regulations. Electrical
information can be found on the rating plate.
ZC921-621 - Instruction Manual.indd 5 20/11/2015 10:32

Instruction manual ZC621 / ZC921
6
Please keep this instruction manual for future reference
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for recycling advice.
This appliance is marked according to the European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling
of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for
waste disposal.
For more detailed information about treatment, recovery and recycling of this product,
please contact your local council, your household waste disposal service or the retailer
where you purchased the product.
CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all
applicable legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility
(EMC).
ZC921-621 - Instruction Manual.indd 6 20/11/2015 10:32

Instruction manual ZC621 / ZC921
7
Please keep this instruction manual for future reference
INSTRUCTIONS FOR INSTALLATION
Before you start
- Read this manual carefully and completely.
- The cooker hood conforms to related appliances standards. Please check your local building codes for any additional
requirements.
- The appliance has been manufactured as class I, therefore earthed connection is necessary. The cooker hood must be
installed so that the plug is easily accessible.
Planning your installation
- Measure the floor to ceiling height.
This hood can be installed on walls between 8ft and 9ft tall.
- Find the centre point of your opening. Mark a plumb line through
this point from ceiling to your range/hob.
- Check your range/hob user manual for the minimum distance
above your cooking surface. The minimum distance between any
element or flame height and the nearest combustible surface
is 61cm.
- Decided where the ductwork will run between the hood and the
outside. Short, straight duct runs will provide the most air flow.
- If a recirculating kit is required (code: CAP24CF), you may
purchase one through your dealer or visit www.caple.co.uk.
Remove all packaging
- Remove the packaging with the product in place. Cut off the packing ribbons and carefully cut open the packaging (do
not cut too deeply), remove the packaging. Check that the product is free from transport damage. Any damage should
be reported immediately to the carrier or retailer. Damage, faults and missing parts must be reported immediately to the
retailer.
ZC921-621 - Instruction Manual.indd 7 20/11/2015 10:32

Instruction manual ZC621 / ZC921
8
Please keep this instruction manual for future reference
Installing the ductwork
- Plan where the ductwork will run between the hood and the outside.
The hoods exhaust vertically but can be ducted to the rear behind the
chimney duct through an outside wall or vertically up through the
ceiling to the roof. A short straight duct run will produce the most air
flow. Length and elbows will reduce the efficiency of the blower.
- Install a roof or wall cap. Connect a 150mm round duct to the cap
and work backwards toward the hood. Ensure joints are completely
sealed with duct tape.
Fixing to a wall
- Before mounting the hood, plug in and test all functions for correct
operation.
- Remove the filters from the bottom of the hood to prevent damage
during the installation.
- With assistance, hold the hood temporarily in position ensuring the bottom
is above the minimum clearance for the cooking surface. Mark on the wall
the holes for the two mounting screws.
- Drill the holes (A) at the distances indicated. Use the appropriate screws
and screw anchors for your wall type (e.g. reinforced concrete, drywall,
etc.). If necessary, prepare back wall with cross framing for secure
installation.
- Mount the hood on the wall screws. Align it in a horizontal position
relative to cabinets. When the hood has been adjusted, secure unit by
tightening screws (A).
- Connect a 150mm duct tube (not included) to the exhaust piece
using duct tape on all seals. (B)
Fixing the chimney flu
- Carefully loosen but do not separate the telescopic chimney duct pieces.
- Arrange the electrical power supply within the dimensions of the chimney
duct.
- Adjust the width of the support bracket to match the upper duct. Fix it
to the ceiling using the screws so that it is centred in line with your
hood and at a distance from the ceiling indicated.
A
B
ZC921-621 - Instruction Manual.indd 8 20/11/2015 10:32

Instruction manual ZC621 / ZC921
9
Please keep this instruction manual for future reference
Installation guidelines
Note:
The above installation guideline is for reference only, please contact your local dealer for a installation service.
Note:
The cooker hood should be placed at a minimum distance of 65-76cm above the hob. It is the manufacturer of the hob who
determines the clearance required. The clearance quoted by the hob manufacturer must be followed. In the absence of any
instructions supplied with a gas hob the minimum distance between the hob and the hood must be at least 760mm.
Levelling device
- When mounting the hood on the wall, the level can be adjusted by turning the two screws on the motor housing.
650 -760mm
1200 - 1700mm
Wall-mounted Duct-out
650 -760mm
1200 - 1700mm
ZC921-621 - Instruction Manual.indd 9 20/11/2015 10:32

Instruction manual ZC621 / ZC921
10
Please keep this instruction manual for future reference
Installation alternatives
The cooker hood can be installed in the following ways:
Circulating indoor air (A) or outdoor venting (B)
Important
- If a two-part connection tube is used, the lower section must sit outside the upper section.
- Do not connect the cooker hood exhaust to a duct used to circulate hot air or vent steam from another appliance.
- Always use protective gloves when installing the appliance.
OPERATING INSTRUCTIONS
Operations
- For optimum performance when removing cooking odours, it is recommended that you turn on your cooker hood 15
minutes prior to cooking and you leave it operating for 15 minutes after cooking.
- Clean the surfaces of the cooker hood regularly using a non-abrasive detergent.
- The anti-grease filters capture the grease particles suspended in the air. They will accumulate grease and dirt depending on
the frequency of the use of your range/hob.
- In order to prevent a fire hazard, it is recommended that you clean the aluminium filter at least every 2 months
Warning:
- Do not attempt to remove the filters while the cooker hood is operating.
- Disconnect the electrical plug prior to any maintenance.
- This appliance is not intended for use by young children or infirm persons without supervision.
- There should be adequate ventilation in the room when the cooker hood is used at the same time as other fuel burning
appliances.
A B
ZC921-621 - Instruction Manual.indd 10 20/11/2015 10:32

Instruction manual ZC621 / ZC921
11
Please keep this instruction manual for future reference
Description of touch controls
CARE AND MAINTENANCE
Important
Before cleaning or maintenance please switch off the electricity supply and remove the plug from the wall.
Regular cleaning
- Use a soft damp cloth with lukewarm mildly soapy water or household cleaning detergent. Never use metal pads,
chemicals, abrasive material, abrasive cleaning creams or stiff brushes to clean the appliance.
Cleaning the grease filter
- Clean the filter every month to help minimise the risk of fire.
- The filter collects grease, smoke and dust, therefore the filter is directly affecting the efficiency of the cooker hood. If not
cleaned, the grease residue (which is potentially flammable) will saturate the filter. It can be easily cleaned with warm water
and washing up liquid, alternatively the filters can be cleaned in your dishwasher. Please ensure no other items are washed
with the filters, they must be washed separately to prevent food becoming trapped in the gauze. Cleaning the grease filters
in the dishwasher may lead to discolouration, this is normal and is a not a fault with the product.
Replacing your charcoal filter
- This only applies if you are using the hood in recirculation mode (not vented to the outside). The charcoal filter traps your
cooking odours and they need to be replaced, this can vary depending on how frequently the cooker hood is used. We
recommend replacing them at least every 6 months.
- This extractor uses CAP24CF charcoal filter. Filters can be purchased directly from www.caple.co.uk.
123
Touch
Touch
Touch 3 seconds
Touch
Touch
Touch 3 seconds
Touch
Touch
Touch
Touch
1
2
3
Low speed setting
Turn off after 5 min.
Turn off after 5 min.
Medium speed setting
Off
High speed setting
Off
On
Off
Off
ZC921-621 - Instruction Manual.indd 11 20/11/2015 10:32

Instruction manual ZC621 / ZC921
12
Please keep this instruction manual for future reference
How to replace the charcoal filter
Squeeze the clips on the charcoal filter and pull the filter back towards you to remove it.
Replacing the bulbs
- This extractor is fitted with two 1.5W LED lights. The illumination is designed for use during cooking and not for prolonged
periods of time to light the kitchen. Prolonged use of the lights may reduce the life of the bulbs.
Warning
Do not touch or change the bulbs when the hood is operating. Wait until the bulb is cool before removing.
Use the same bulbs as the originals (1.5W LED). Replacement bulbs are available from www.caple.co.uk.
Removing the LED lights
- With the grease filter removed, from inside the hood press the light fixture out of its mounting bracket.
- Unplug the light from the wiring harness. Avoid direct contact between the lens and your hand Then replace with the new
one.
- Push the light into its mounting bracket
Note
The light is only meant for use during cooking and not for illuminating the surroundings for longer periods. If the light is
used for longer periods, this will considerably shorten the life of the bulbs.
ZC921-621 - Instruction Manual.indd 12 20/11/2015 10:32

Instruction manual ZC621 / ZC921
13
Please keep this instruction manual for future reference
DIMENSIONS
460-850mm
300mm
300mm
500mm
600mm
60mm
560-1050mm
320mm
320mm
500mm
900mm
60m
m
ZC921-621 - Instruction Manual.indd 13 20/11/2015 10:32

Instruction manual ZC621 / ZC921
14
Please keep this instruction manual for future reference
TROUBLESHOOTING
PROBLEM POSSIBLE REASON SOLUTION
Hood doesn’t turn on
No electrical supply
Power cord is damaged
Check the plug is connected
Check the main switch is turned on
Contact Caple Service
Poor airflow
Aluminium grease filters are clogged
Charcoal filters are clogged –
recirculating mode only
Clean the filters and replace when dry
Replace the charcoal filters
Hood is vibrating Hood is not secured properly Check the installation of hood. Tighten
mounting screws
Motor is running but there is no airflow Butterfly valve jammed Contact Caple Service
Motor stops after a few minutes
High temperature safety device
activated
The hood is installed too close to the
cooking surface
The kitchen is not sufficiently ventilated
The hood must be at least 61cm from
the stove
Strong cooking smell
Fan speed is too low
Charcoal filters not installed
Use a higher setting
In recirculation mode charcoal filters
must be installed
Oil dripping onto hob Aluminium grease filter saturated Wash the aluminium grease filters
Whirring sound Something in contact with fan blade Contact Caple Service
Lights are working fan isn’t Contact Caple Service
Fan is working but lights are not Contact Caple Service
Guarantee and servicing
Before booking a service call read the troubleshooting table above. For more information on guarantee and service
conditions, please contact Caple Service on 0117 938 7420 or email [email protected].
ZC921-621 - Instruction Manual.indd 14 20/11/2015 10:32

Instruction manual ZC621 / ZC921
15
Please keep this instruction manual for future reference
Guarantee
Caple undertake that if within two years of the date of the purchase this appliance or any part thereof that is proved to be
defective by reason only of faulty workmanship or materials, we will at our option repair or replace the same free of any
charge for labour or materials on condition that:
- Documentation must be provided before a guarantee repair commences to confirm that the extractor is within the
guarantee period.
- The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
- The appliance has been used for normal domestic purposes only, and in accordance with the operating and maintenance
instructions.
- The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by
us.
- All service work under this guarantee must be undertaken by Caple Service Centre.
- Any appliance or defective part replaced shall become the property of this company.
- If a service call is made and it is found that the installation has not been carried out correctly or customer misuse/abuse is
involved the cost of the service call has to be paid for by the user before any service work is carried out.
Exclusions
This guarantee does not cover:
- Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable
parts of glass or plastic.
- Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United Kingdom.
- Appliances found to be in use within a commercial environment, plus those which are the subject of rental agreements.
- This guarantee is in addition to and does not affect your statutory and legal rights.
ZC921-621 - Instruction Manual.indd 15 20/11/2015 10:32

Instruction manual ZC621 / ZC921
16
Please keep this instruction manual for future reference
Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW
t: 0117 938 7420
e: [email protected]
www.caple.co.uk
ZC921-621 - Instruction Manual.indd 16 20/11/2015 10:32