Car-Interface v.LOGiC CI-V5-CCC-PNP User manual

Version 05.02.2018 CI-V5-CCC-PNP
v.LOGiC Intelligent Solution
Interface
CI-V5-CCC-PNP
Compatible with E-series BMW and Mini with
navigation system or radio and 6.5” or 8.8”
monitor with 10pin BMW LVDS connector
Product features
Own on-screen display and setup
Rear-view camera input
Automatic switching to rear-view camera input on engagement of reverse gear from
all operation modes
Front camera input
Manual switching to rear-view camera (only for vehicles with PDC button)
Manual return from rear-view and front camera (cancellation of automatic switching)
2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC,
camera, reverse gear)
Picture-in-picture mode combining after-market rear-view and front camera
picture(s) with factory parking sensor graphics
Compatible with all factory video accessories (e.g. rear-view camera, Top-View,
nightvison, DVD-changer, TV-tuner)
USB update-port for software-updates by consumer

Version 05.02.2018 CI-V5-CCC-PNP
Page1
Contents
1. Prior to Installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Setting the dip switches of the interface-box V5C-M631
1.4. LED’s of the interface-box V5C-M631
2. Connection schema
3. Installation
3.1. Connecting interface-box and harnesses
3.2. LVDS connection
3.2.1. After-market front camera
3.2.1.1. Connection to the after-market front camera
3.2.1.2. Settings for connecting an after-market front camera
3.2.2. After-market rear-view camera
3.2.2.1. Connection to the after-market rear-view camera
3.2.2.2. Settings for connecting an after-market rear-view camera
3.2.3. After-market navigation
3.2.4. Configurable trigger outputs
3.3. Picture settings
4. Operation
4.1. OSD –On-screen display
4.1.1. OSD –Operation
4.1.1.1. 1- and 2-button iDrive
4.1.1.2. 2-button iDrive in Mini
4.1.2. OSD –Additional setting options
4.2. Video-in-motion function
4.3. Selecting the interface as current video source
5. Specifications
6. Connections (interface-box)

Version 05.02.2018 CI-V5-CCC-PNP
Page2
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.

Version 05.02.2018 CI-V5-CCC-PNP
Page3
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
Requirements
Navigation E-series and Mini with navigation system or radio with 6.5” or
8.8”monitor with 10pin BMW LVDS connector
Interface-box
V5C-M631
HW_____ SW_____
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
V5C-UNI01
harness
LVDS cable
V4C-LVDS10
TV-BM01
harness

Version 05.02.2018 CI-V5-CCC-PNP
Page4
1.3. Setting the dip switches of the interface-box V5C-M631
Dip 1 and 2 on the back of the interface-box V5C-M631 are used to set the monitor type. The
default setting is:
Vehicle/ navigation
Dip 1
Dip 2
Dip 3
M-ASK - version 1
OFF
OFF
OFF
M-ASK - version 2
OFF
ON
OFF
CCC - version 1
ON
OFF
OFF
CCC - version 2
ON
OFF
ON
After each change of the dip switch settings you have to execute a power reset of the
interface-box!
1.4. LED‘s of the interface-box V5C-M631
Validinput source
CAN ok
Power

Version 05.02.2018 CI-V5-CCC-PNP
Page5
2. Connection schema

Version 05.02.2018 CI-V5-CCC-PNP
Page6
3. Installation
Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent
12V source. If according to factory rules disconnecting the battery is to be avoided, it is
usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show
success, disconnect the battery with a resistor lead.
If power source is not taken directly from the battery, the connection has to be checked
for being start-up proven and permanent.
Prior to wire and device installation we suggest to connect and test correct function of all
after-market and factory infotainment equipment!
The interface is installed on the backside of the head unit.
3.1. Connecting interface-box and harnesses
Remove the female Quadlock connector of the vehicle harness from the rear of the
navigation computer.
Remove optical leads from the female Quadlock connector of the vehicle harness and
insert them into the female Quadlock connector of harness TV-BM01 at the same
position.
Connect female Quadlock connector of vehicle harness to the male Quadlock
connector of harness TV-BM01.
Connect female Quadlock connector of harness TV-BM01 to the male Quadlock
connector of the head unit.
1
2
3
4

Version 05.02.2018 CI-V5-CCC-PNP
Page7
Connect female 8 pin molex connector of the harness TV-BM01 to the
male 8 pin molex connector of the harness TV-BM01.
Connect female 12pin AMP connector of the harness TV-BM01 to the
front site of the V5C-M631 interface box.
3.2. LVDS connection
Connect the female 10pin Micro-Fit connector of the LVDS cable V4C-LVDS10 to the
male 10pin Micro-Fit connector (LVDS-OUT) on the rear of the interface-box
V5C-M631.
Remove the female 10pin BMW LVDS connector of the vehicle harness at the side of
the factory monitor and connect it to the male 10pin BMW LVDS connector (LVDS-IN)
on the front of the interface-box V5C-M631.
Connect the female 10pin BMW LVDS connector of the LVDS cable V4C-LVDS10 to
the male 10pin BMW LVDS connector of the factory monitor.
5
6
1
2
3
1
3
2
Interface-box
V5C-M631
REAR
10pinBMW
LVDSfemale
vehicle harness
Sideview of the
factory monitor
LVDScable
V4C-LVDS10

Version 05.02.2018 CI-V5-CCC-PNP
Page8
3.2.1. After-market front camera
3.2.1.1. Connection to the after-market front camera
Connect the video RCA of the after-market front camera to the female RCA connector
“FRONT CAM” of the interface box V5C-M631.
-The pink wire of harness V5C-UNI01 can be used
for +12V electric power supply (max. 1A) of the
after-market front camera. Configure in the OSD-
menu “MISC”, menu item “POWER OUT 2” the
designated electric power supply (see chapter
“Configurable switching outputs”).
-
Interface-Box
V5C-M631
VORDERSEITE
Frontkamera
+12VKamera
Stromversorgung
Anschlusskabel
V5C-UNI01
PowerOut1(max.1A)
1
2
1
2

Version 05.02.2018 CI-V5-CCC-PNP
Page9
3.2.1.2. Settings for connecting an after-market front camera
You have to configure some settings in the OSD-menus INPUTS and MISC if you want to
connect an after- market front camera
(Operation of the OSD: see chapter “OSD-Operation”).
OSD-menu
Menu item
Setting
Explication
INPUTS
FRONT CAM
OFF
No front camera connected
ON
Switches to front camera if parking process is
enabled and reverse gear is released
ReverseLogic
Intelligent
For vehicles with PDC button. Enabled while
parking process and up to 20 km/h or
together with PDC if existing
Gear only
For vehicles without PDC button. Enabled
while parking process and up to 20 km/h.
MISC
OEM PDC CAR
Horizontal
PDC-display of the vehicle is horizontal
Vertical
PDC-display of the vehicle is vertical
-
Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling
other modes (e.g. radio). After deactivation you can’t enable the parking process again until
the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be
disabled and enabled again, if existing.