Caraudio-Systems TF-MYGIG User manual

Version 19.07.2019 TF-MYGIG
TV-Free
Video-in-motion Interface
TF-MYGIG
Compatible with Chrysler C300,
Dodge and Jeep vehicles
with MYGIG navigation systems
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.

Version 19.07.2017 TF-MYGIG
Page1"
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Setting the Dip-switches of the CAN-Box TV-500
1.4. Pin-assignments
2. Installation
3. Activation of the video-in-motion function
4. Specifications
5. Technical support
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
CAN-box TV-500
HW_____ SW_____
Harness
TV-MYGIG
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.

Version 19.07.2017 TF-MYGIG
Page2"
1.2. Check compatibility of vehicle and accessories
1.3. Setting the Dip-switches of the Can-Box TV-500
Vehicle/ navigation
Dip 1
Dip 2
Dip 3
Dip 4
Dip 5
Dip 6
Video-in-motion permanent
ON
OFF
OFF
OFF
ON
ON
Video-in-motion selective*
OFF
OFF
OFF
OFF
ON
ON
* With dip1 to OFF the included green cable is used to activate the video-in-motion function.
Note: Dip switch functions of the TV-500
Dip 1 – activation TV-free
Dip 2 – no function
Dip 3 – no function
Dip 4 – no function
Dip 5 – CAN-bus termination resistor on the vehicle side
Dip 6 – CAN-bus termination resistor on the head-unit side
1.4. Pin-assignments
Pin-assignment vehicle connector
Cable colour
Assignment
○● White/Orange
CAN-HIGH - Pin 13
○ White
CAN-LOW - Pin 2
● Red
+12V Permanent - Pin 1
●● Black/Green
Ground - Pin 12
Pin-assignment of the CAN-Box TV-500 (Molex 8pin)
Cable colour
Pin-No.
Assignment
● Yellow
Pin 4
CAN-HIGH – connection to the head-unit
● Blue
Pin 3
CAN-LOW – connection to the head-unit
●● Yellow/Black
Pin 8
CAN-HIGH – connection to the vehicle
●● Blue/Black
Pin 7
CAN-LOW – connection to the vehicle
● Red
Pin 1
+12V permanent
● Black
Pin 5
Ground
● Green
Pin 6
Activation of the video-in-motion function
(+12V = TV-free activated)
● White
Pin 2
No Function
Requirements
Vehicle Chrysler, Dodge, Jeep
Navigation MYGIG RER/REW/REN/REP/RHW and UConnect (Jeep) navigation
systems

Version 19.07.2017 TF-MYGIG
Page3"
2. Installation
Switch off ignition and disconnect the vehicle’s battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle is
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
Instruction for Chrysler C300:
1. Remove the front panel from the centre console, which is
attached to multiple clips.
2. Remove the 4 TORX screws and pull the device out of the
centre console.
3. Remove the grey female 22pin connector from the rear of
the device and connect it to harness TV-MYGIG. Connect the
female 22pin connector of harness TV-MYGIG to the device.

Version 19.07.2017 TF-MYGIG
Page4"
3. Activation of the video-in-motion function
The video-in-motion can be activated and deactivated by Dip 1 or alternatively by the
included loose green cable in connection with a switch (not included in delivery).
Video-in-motion permanent
With dip1 to ON the video-in-motion function is activated permanently without disturbing
the navigation performance.
Video-in-motion selective
With dip1 to OFF the included green cable is used to activate the video-in-motion function.
Connect a switch to the green cable and connect the green cable to +12V ACC.
● +12V = TV-Free is activated
● 0V = TV-Free is not activated
Note: The loose white cable is not required and must be isolated.
4. Specifications
Operation voltage 10.5 – 14.8V
Stand-by power drain >1mA
Operation power drain ~60mA
Power consumption ~0,72W
Temperature range -30°C bis +80°C
Weight 44g
Measurements (box only) B x H x T 70 x 20 x 47 mm
5. Technical Support
Caraudio-Systems Vertriebs GmbH
manufacturer/distribution
In den Fuchslöchern 3
D-67240 Bobenheim-Roxheim
email [email protected]
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.