Audio Kit for
Qz, Q1 and Q3
6 7
8 9
2 3
5
1
4
1
Noise canceling
microphone
2
Hybrid mic
3
Release Tab
4
Speakers
5
Speaker Jack6 Corded
Microphone
(*Only with Q1/Q3)
7
Replacement mic sponges
8
Allen wrench
9
Alcohol pads
Speaker Boos ter
pads
Velcro p ads
Glue plates
Hybrid mic clip
CONTENTS OPTION B: USING THE GLUE PL ATE
1
Remove the Back P late by taking out bo th screws
2
Use the Alcohol p ad to clean the exac t spot on the helme t
3
Peel o protec tive backing sh eet
4
Press here for 15seconds
5
Allow the glue to dr y for 24 hours
6
Fasten both screws tightly
Glue the Audi o Kit onto your h elmet when t he standar d Back
Plate metho d cannot be us ed. Choose w hich of the2 gl ue plates
is most suit able for you r helmet.
Whilewe have no reason to believe that the gluing option
mightnegatively aec t any helmet, Cardo does not assume
anyresponsibility, irrespec tive of its nature and circumstances.
The Glue Plate i s oered as an o ption that yo u may use at your ow n risk and subj ect to reno uncement of a ny
future claims.
POSITIONINGTHE HYBRID MICROPHONE
1
Open
the liningbe tween the helmet’s inner padding.
Use the Velcro pad to hold the Hybrid Micr ophone in
place
. Attach the M icrophon e to the Velcro pad .
2
Adjust
the locati on so that the
microphone
is located o pposite
the
center of your m outh.
PLACING THE SPEAKERS
For best cla rity, place speak ers direct ly opposite
and close to th e ears. Helmet s with deep re cesses
may require pa dding to bring t he speakers clo ser
for ideal positioning. Optional speaker booster
pads are prov ided for this pu rpose.
Tou se, place the spea ker booster p ad between t he
Velcro pad in the h elmet cavit y and the speake r.
1
Attach Velcr o pads to inside of H elmet.
2
Cross the lon g speaker wire over t he center of
the helmet to en hance FM radio rec eption.
Using two speakers i nside the helmet may b e
prohibited in cer tain jurisdictio ns. If this is the case,
position both spea kers on one side of the h elmet.
CHANGING THE MICROPHONE TYPE
Removing:Before changing
the microphone, completely
remove the Audi o Kit and
backplate f rom the helmet .
Attaching: Rep lace the
screws to rea ttach the
backplate to t he Audio Kit
before reassembling on the
helmet and fully tightening
the screws.
POSITIONINGTHE CORDED MICROPHONE
Attach Velcro t o inside front of he lmet
The CordedMicrophone can be used with Full
face helmets only (not Modular helmets).
Some helmets with air vents may requirethe mic
to be repositioned if mic audio is aected.
REPLACING THE CORDED MICROPHONE SPONGE
A replacement co rded micropho ne sponge is
provided fo r future use shou ld you need it.
NOTE: The wire s to the microphon e are delicate. Avoid tou ching them.
1
Pinch and pull existing microphone sponge
2
Carefully remove the existing sponge.
3
Remove protective backing sheet from replacement sponge
4
Carefully a ttach the new sp onge to the microp hone
Installation Guide
OPTION A : USING THE BACK PLATE
1
Loosen both screws
2
Push the back pla te between
the helmet ’so uter shell and
inner padding
3
Tighten the screws
THIS CAN ONLY
BE DONE ONCE!
English - Chinese
ATTACH THE SCALA RIDER AUD IO KIT TO YOUR HELMET
Attach the scala rider
Audio Kit to your h elmet
with the standard
Backplate using the
following instructions
MAN00124R
www.cardosystems.com
USA & Canada: 1-800-4 88-0363
International: +49 89 450 36819
