Cardo Systems scalarider q1 User manual

ThankyouforcontactingtheCardoSystemsSupportCenter.

Wearen’tawareofanyissuesbetweenthescalariderQ1andthatversionoftheTomTomRider.Iwould
recommendtousethefollowingstepstoresetyourdevices,createanewpairing,andtestfurther.
ToresetyourscalariderQ1headset:
1.TurnthescalariderQ1moduleonbypressingandholdingtheICbuttonuntilthree(3)blueflashesappear.
2.WiththeQ1flashingslowlyinblue,pressandholdtheVolumeUpbuttonuntilyoureceivearedandblue
alternatingflash.
3.ReleasetheVolumeUpbutton.Withthedeviceflashingredandbluealternating,pressandholdtheMMbutton
forapproximatelythree(3)seconds.Theredandblueflashingshouldchangetoaslow,solidpurpleflash.
4.Theheadsetwillflashpurpleslowly,approximatelyfive(5)times,followedbythree(3)redflashes.
5.Themoduleshouldthenbepoweredoff,indicatingthattheresethasbeencompleted.Repeatthesestepswith
bothheadsets.
TocreateanewpairingbetweenyourscalariderQ1headsets:
1.TurnbothscalariderQ1modulesonbypressingandholdingtheICbuttonuntilthree(3)blueflashesappearon
eachheadset.
2.Makesurebothmodulesareinstand‐bymode,whichisindicatedbyasingleblueflasheverythree(3)seconds.
3.FromoneQ1module,pressandholdtheICbuttonuntilthemodulebeginstoflashredrapidly.Youwillseethree
redflasheslikethedeviceispoweringoff,butkeepthebuttonheldinuntilitflashesredrapidly.ThisistheIntercom
Pairingmode.*
4.Repeatstep3onthesecondQ1module.
5.Bothmodulesshouldcontinuetoshowarapidredflashuntiltheyhavefoundeachother.Atthattime,each
modulewillsimultaneouslyshowasolidredlightforafewseconds.Bothheadsetswillreturntostand‐bymode
simultaneouslyafterthat,indicatingthatthepairingprocesshasbeencompleted.**

*OncetheQ1moduleisinIntercomPairingmode,itwillreturntostand‐byautomaticallyaftertwo(2)minutesifa
pairingisnotcompleted.
**Ifbothmodulesdonotshowasolidredforafewsecondsandoneheadsetreturnstostand‐bymodebeforethe
other,theheadsetsdidnotcompletethepairingprocesssuccessfully.

ToresetyourTomTomRider:ToresolveaBluetoothissue,youwillalsoneedtoresetyourGPStofactorysettings.
OnmostTomTomRiders,thiscanbedonebythroughthesettingsmenu.(Note:Thisresetwillrestorethedevicesto
itsfactorysettings.Alluserdatawillbeerased.PleaserefertotheTomTommanualforinstructionsonbackingup
anydatayouwishtosave).


TopairascalariderQ1headsetwithyourGPS:
1.TurnthescalariderQ1moduleonbypressingandholdingtheControlbuttonuntilthree(3)blueflashesappear.
2.WiththeQ1flashingslowlyinblue,pressandholdtheVolumeDownbuttonuntilyoureceivearedandblue
alternatingflash.
3.OncetheQ1moduleisflashingredandbluealternating,searchfor/AddaBluetooth‘audio’device/headsetfrom
yourGPS.
4.TheGPSshouldmomentarilydiscoverthe‘scalariderQ1’.Ifpromptforapasskey,thiswillbefourzeros(0000).
5.TheGPSshouldmomentarilyconfirmthatthepairinghasbeencompleted,andtheheadsetshouldreturnto
stand‐bymode.
Pleasefeelfreetocontactusifwecanassistyouwithanyotherquestions.
Bestregards,
TechnicalSupport
CardoSystems,Inc.
Phone:+1412.788.4533
Fax:+1412.788.0270
TollFree:+1800.488.0363
International:+49.894.503.6819
[email protected]

www.cardosystems.com