Carefree FREESTYLE EVOLUTION User manual

07
T
A
P
r
In
s
B
T
Pi
t
A
d
M
a
0036-001r3
R
V
Rea
d
and
pro
d
A
BLE OF
C
r
oduct Ov
e
Compon
e
Freestyl
e
s
tallation .
Bracket I
n
Mountin
g
Ju
m
T
12 Syste
m
BT12 Co
n
A
wning
S
A
wning
L
Wiring Di
Setting t
h
t
ch Adjus
t
d
justing th
a
nual Ove
r
V
d
this man
u
safety pre
c
d
uct to not
o
C
ONTEN
T
e
rview.......
e
nt Checklis
e
RM Brack
e
.................
n
stallation ..
the Awnin
g
m
ping the M
o
m
Installati
n
trol Modul
e
S
witch Instal
l
L
ights Switc
h
agram........
h
e System i
n
t
ment........
e Extend
L
r
ride .........
u
al before i
n
c
autions in
t
o
perate pr
o
T
S
.................
t
..................
e
t Kits ..........
.................
...................
g
..................
o
tor (with B
T
on ............
e
Installation
l
ation ..........
h
Installation
...................
n
to Pairing
M
.................
L
imit .........
.................
Pri
n
n
stalling o
r
t
his manu
a
o
perly.
.................
..................
.
..................
.
.................
..................
.
..................
.
T
12) ............
.
.................
..................
.
..................
.
..................
.
..................
.
M
ode...........
.
.................
.................
.................
n
ted in USA
FR
E
12V M
r
using this
a
l can resul
t
.................
.
..................
.
..................
.................
.
..................
.
..................
.
..................
.................
.
..................
.
..................
.
..................
.
..................
.
..................
.................
.................
.................
I N
ST
E
EST
Y
M
OTORIZED
product.
F
t
in person
a
.................
...................
...................
.................
...................
...................
...................
.................
...................
...................
...................
...................
...................
.................
.................
.................
ST
ALLA
T
Y
LE E
V
R OOF M O
U
F
ailure to fo
a
l injury an
d
.................
..................
.
..................
.
.................
..................
.
..................
.
..................
.
.................
..................
.
..................
.
..................
.
..................
.
..................
.
.................
.................
.................
Jan
T
ION
M
A
V
OLU
U
NTED B O
X
llow the in
s
d
/or cause
t
.................
.
..................
.
..................
.................
.
..................
.
..................
.
..................
.................
.
..................
.
..................
.
..................
.
..................
.
..................
.................
.................
.................
uary, 2020
M
A
NUA
L
TION
X
A WNING
s
tructions
t
he
............. 4 
...............5
...............5
............. 7 
...............7
...............7
...............7
............. 8 
...............9
.............10
.............10
.............11
.............13
........... 14 
........... 14 
........... 14 

FREESTYLE EVOLUTION AWNING Installation Manual Carefree of Colorado
2 070036-001r3
NOTICES AND DISCLAIMERS
TRADEMARKS
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc.
Use of such marks by Carefree of Colorado is under license.
Other trademarks and trade names are those of their respective owners.
STATEMENTS OF COMPLIANCE
●BT12 Control Module ●BT Motion Sensor ●BT Remote
FCC and IC identification numbers are located on the exterior surfaces of the individual components.
FCC C OMPLIANCE
These devices comply with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) These devices may not cause harmful interference and, (2) These devices must accept
any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
IC C OMPLIANCE
These devices comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two
conditions: (1) These devices may not cause harmful interference and, (2) These devices must
accept any
interference received, including interference that may cause undesired operation.
Ces appareils sont conformes aux normes RSS exonérées de licence d'Industrie Canada. L'opération est
soumise aux deux conditions suivantes: (1) Ces appareils ne doivent pas causer d'interférences nuisibles et, (2)
Ces appareils doivent accepter toute interférence reçue, y compris les interférences pouvant entraîner un
fonctionnement indésirable.
FCC/IC R ADIATION E XPOSURE S TATEMENT
●BT12 Control Module ●BT Motion Sensor
This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The
minimum distance between the radiator and people is designed to be 20cm when installed and operated.
Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non
contrôlé. La distance minimale entre le radiateur et les personnes est de 20cm lorsqu'installé et utilisé.
●BT12 Remote
This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The
minimum distance between the radiator and people is designed to be 5mm when operated.
Cet équipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non
contrôlé. La distance minimale entre le radiateur et les personnes est de 5mm (à l'exclusion des extrémités:
mains, poignets, pieds et chevilles) lors de l'utilisation.

C
a
07
D
I
Th
C
a
thi
s
th
a
C
o
Th
pa
g
pr
o
C
a
pr
o
wi
t
S
E
S
A
N
G
e
(D
I
ca
w
w
N
al
u
C
a
a
refree of Co
l
0036-001r3
I
SCLAIME
e BT12 Wi
a
refree of C
o
s
document
at
the info
r
o
lorado ass
u
e informati
o
g
e. Caref
r
o
cedures, d
e
a
refree of C
o
o
ducts only.
t
hout prior w
r
E
RVICE A
N
A
FETY I N
F
W
AR
N
CAU
T
N
OTICE
e
neral S
a
W
AR
N
I
DP), Vinyl
C
ncer or bir
t
w
w.P65war
n
w
o
ho
l
OTICE
u
minum ca
n
a
refree of Co
l
orado
RS
reless Awn
o
lorado, loc
a
is conside
r
r
mation pre
u
mes no liab
o
n containe
d
r
ee o
f
Col
e
scribed in
o
lorado agr
e
Any other
r
r
itten appro
v
N
D S UPP
O
F
ORMATI
O
T
h
p
e
a
v
N
ING
I
n
s
e
T
ION
I
n
m
I
n
a
fety:
N
ING Thi
s
C
hloride a
n
t
h defects
o
n
ings.ca.g
o
W
ARN
o
rking on o
r
W
ARN
CAUT
I
l
ding heav
y
When usi
n
n
be "strip
p
l
orado
ing Control
a
ted in Broo
m
r
ed propriet
a
sented in
ility for error
s
d
in this man
orado res
e
this manu
a
e
es to allow
r
eproductio
n
v
al from Car
e
O
RT
www.
c
www.
c
custo
m
Caref
r
2145
W
Broo
m
80020
O
N
h
is is the s
a
e
rsonal inj
u
v
oid possi
b
dicates a h
e
rious bodi
l
dicates a h
oderate bo
dicates a s
s
product c
a
n
d Formald
e
o
r other rep
r
o
v
ING Sho
c
r
around th
e
ING Alw
a
I
ON Alw
a
y
objects.
n
g fastene
r
p
ed out" an
d
Install
System a
n
m
field, Colo
a
ry to Care
f
the docum
e
s
or for any
d
ual pertains
e
rves the
r
a
l, without pr
i
the reprod
u
n
or translat
i
e
free of Col
o
c
arefreeofc
c
arefreeofc
m
erservice
@
r
ee of Colo
r
W
. 6
th
Ave.
m
field, CO
a
fety alert
s
u
ry hazards
b
le persona
l
azardous
s
l
y injury.
azardous
s
dily injury.
ituation th
a
a
n expose
y
e
hyde, whi
c
r
oductive
h
c
k Hazard.
e
electrical
a
ys wear a
p
a
ys use ap
p
r
s, do not
d
lose the
a
www.caref
r
ation Manu
a
n
d the Car
e
rado, USA.
f
ree of Col
o
e
nt is acc
u
d
amages tha
to the curr
e
r
igh
t
to ca
n
i
o
r
notice.
u
ction of thi
s
i
on of this d
o
rado.
olorado.co
m
olorado.co
m
@
carefree
o
r
ado
s
ymbol. It i
s
. Obey all
s
l
injury or
d
ituation, w
h
ituation, w
h
a
t may resu
y
ou to che
m
c
h are kno
w
h
arm. For
m
Always di
s
system.
p
propriate
s
p
ropriate li
f
over tight
e
a
bility to gr
i
r
eeofcolorad
o
a
l
e
free Conn
e
The inform
o
rado. Ever
y
u
rate and
at
result fro
m
e
nt compon
e
n
cel, chan
g
s
document
d
ocument in
m
m/carefree
c
o
fcolorado.
c
s
used to a
l
s
afety mes
s
d
eath.
h
ich if not
a
h
ich if not
a
lt in equip
m
m
icals incl
u
w
n to the st
a
m
ore infor
m
s
connect b
a
s
afety equi
p
f
ting devic
e
e
n. Soft m
a
i
p and hold
o
.com
F
REE
S
e
cts Mobil
e
ation conta
i
y
effort has
complete.
m
the use of
t
e
nts and sof
t
g
e, alter o
r
for use wit
h
whole or p
a
c
onnects
c
om
le
r
t individ
u
s
ages that
f
a
voided, co
a
voided, m
a
m
ent-relate
d
u
ding Di-is
o
ate of Calif
o
m
ation visit
a
ttery or p
o
p
ment (i.e.
g
e
s and/or h
e
aterials su
c
.
S
TYLE E VOLU
T
e
App are
p
i
ned in or d
been mad
e
However,
C
t
his docume
t
ware listed
r
add any
h
Carefree
o
a
r
t
is strictl
y
u
als to pot
e
f
ollow this
s
uld result i
n
a
y result in
d
damage.
o
decyl phth
o
rnia to ca
u
o
wer sourc
e
g
oggles).
e
lpers whe
n
c
h as fibe
r
aScott Fetz
e
T
ION A WNING
3
p
roducts of
isclosed in
e
to ensure
C
arefree of
nt.
on the title
parts and
of
Colorado
y
prohibited
e
ntial
s
ymbol to
n
death or
minor or
alate
u
se
e
before
n
lifting or
r
glass and
er company

FREESTYLE EVOLUTION AWNING Installation Manual Carefree of Colorado
4 070036-001r3
PRODUCT OVERVIEW
The Freestyle Evolution Awning is a state of the art lateral arm awning. When retracted, the housing
provides protection against the elements while the streamlined styling blends in with the vehicle
appearance. The full tension canopy fabric allows the awning to be partially or fully extended for best
shade coverage.
Each unit is equipped with lateral support arms. No vertical arms interfere with coach sidewalls, custom
graphics or equipment that may be mounted on the sidewalls.
Freestyle Awning Specifications:
Fully retractable and self-storing;
The sealed awning motor operates on standard 12VDC (range 10VDC to 14VDC);
Case and frame are constructed of high-strength aluminum extrusions, protected with a polyester paint finish;
BT12 Wireless Awning Control System is standard.
NOTE: Dimensions shown are approximate. Dimensions may vary based on specific installations.
SPECIFICATIONS
Lengths: centimeters 200 - 241 244 - 254 257 - 297 300 - 500
inches 79 - 95 96 – 100 101 - 117 118 - 197
Extension: 152cm (60") 180cm (72") 200cm (80") 250cm (98")
LEADING EDGE POSITION ACTUATION AND CONTROL
Power: Lateral Arm Spring Minimum Tension Open
Position Control: 12V Motorized
Controller: BT12 Wireless Awning Control System
MOTOR SPECIFICATIONS
Motor Type: Tubular
Power: 12VDC Minimum: 10VDC Output: 30 Watts
Nominal Current: 2.5Amps Max Current: 14Amps (stall @ min voltage)
Power Source: Motor and controls are routed and hardwired into the vehicle’s 12V system
Torque Continuous: 6Nm/4.5 ft-lbs.
Speed 24 rpm
COLORS AVAILABLE
Case Satin, White or Black
Fabric:1Vinyl or Woven Acrylic
Special Note: Dimensions are provided in centimeters. Conversion formulas are provided below;
Inches = Centimeters = Millimeters
2.54 25.4
Centimeters = Inches x 2.54 Millimeters = Inches x 25.4
ragm001
Awning Length
Fabric Width
6"
[15.4cm]
7"
[18cm]
2.5"
[6.4cm]
2.5"
[6.4cm]

Carefree of Colorado Installation Manual FREESTYLE EVOLUTION AWNING
070036-001r3 5
COMPONENT CHECKLIST
ITEM DESCRIPTION QTY NOTE
1 Awning Assembly, Complete 1
2 Mounting Bracket Ordered Separately, Refer to “Freestyle RM Bracket Kits”
3 Switch Kit 1
3a Terminal, Female, .187 18-22 awg 3
3b Terminal, Female, .187 14-16 awg 2
3c Terminal, Female, .25 14-16 awg 1
3d Terminal, Male, .25 14-16 awg 1
4 Covered Bezel, 2 Switch 1 2
5 BT12 Control Module 1 3
NOTES: 1. Specific awning configuration is specified at time of order, including awning length, fabric, color etc. check
awning assembly against original purchase order.
2. The covered bezel (item 4) is optional and ordered separately. Refer to page 8 for information about
NFPA 1192 RV Standard, Section 6.4.9 (Switch Installation Requirements).
3. The BT Motion Sensor is factory installed in the lead rail on the motor side.
FREESTYLE RM BRACKET KITS
Bracket kits are ordered separately. Several types are available based on the application installation.
Bracket mounting instructions are separate instructions that supplement this manual.
BS0012 Sprinter
4.5m & 5m
Mill Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-012
BS0013 Sprinter
4m and less
Mill Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-013
BS0014 Dodge ProMaster; Fiat Ducato
(-4) 4 Brackets 3.5m
(-5) 5 Brackets 4m
Mill Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-014
RETRACT
ON
EXTEND
OFF
Awning Control
1
2
45
RETRACT
ON
EXTEND
AwningControl
OFF
3a 3d3c3b
3
ragm002
(x3)
(x3)
42"
BS0012a
28"
(x2)
(x2)
36"
BS0013a
28"
-4 (x4)
-5 (x5)
BS0014a

FREESTYLE EVOLUTION AWNING Installation Manual Carefree of Colorado
6 070036-001r3
BS0016 Flat Roof
(-3) 3 Brackets 4m
(-4) 4 Brackets 4.5m & 5m
Mill Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-016
BS0017 Sprinter – No Rail
(-28-2) 2 Brackets up to 4m
Mill Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-017
FULL LENGTH BRACKETS
BS0015 Ford Transit
(-118-XX) Full Length 3m
(-138-ML) Full Length 3.5m
(-157-XX) Full Length 4m
Mill (ML) or Black (JV) Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-015
BS0018 Sprinter – No Rail
(-118-XX) Full Length 3m
(-157-XX) Full Length 4m
(-177-XX) Full Length 4.5m
Mill (ML) or Black (JV) Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-018
BS0019 Sprinter used w/ OEM Rail or Flat Roof
(-118-XX) Full Length 3m
(-157-XX) Full Length 4m
(-197-XX) Full Length 5m
Mill (ML) or Black (JV) Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-019
BS0021 Low Profile RM Mounting Bracket Kit
(-157-ML) Full Length 4m
(-177-XX) Full Length 4.5m
Mill (ML) or Black (JV) Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-021
BS0023 Dodge ProMaster
(-157-XX) Full Length 4m
Mill (ML) or Black (JV) Finish
Bracket and Awning Hardware included
Instruction Supplement: 052570-023
BS0016a
28"
28"
BS0017a
Full Length
BS0015a
Full Length
BS0018a
Full Length
BS0019a
BS0021a
Full Length
BS0023a
Full Length

Carefree of Colorado Installation Manual FREESTYLE EVOLUTION AWNING
070036-001r3 7
INSTALLATION
BRACKET INSTALLATION
Install the mounting brackets according to the
supplement instructions for the bracket kit.
NOTE: Install the brackets according to the
bracket design. To correctly support the awning,
the brackets must be positioned below the arm
case knuckles. After the brackets are installed,
go to "Mounting the Awning".
MOUNTING THE AWNING
These steps apply to all bracket configurations.
1. If not previously done, in the rear track of the mounting plate(s),
start three (3) M6 x 20 screws and square nuts through the
holes. Do not tighten at this time.
NOTE: Locate 1 screw and nut at each end of the awning, the third
screw and nut should be located near the center of the awning.
2. Lift and set the awning into the hooks of the mounting brackets.
Pull the case forward to engage the brackets fully.
3. Horizontally center the awning on the brackets.
4. Tighten the rear screws. Torque to 10 ft-lbs [13.6 nm].
5. The motor and switch wires come out of the back of motor endcap.
Drill a 5/16" [8mm] hole into the vehicle in the area shown.
NOTE: Locate the hole to avoid interior framing, cabinets and
electrical components.
Ensure that the motor wires are accessible after routing.
Jumping the Motor (with BT12)
This method is used if the BT12 Wireless Awning Control System is to be used.
1. Temporarily connect the ends of the motor wires to a 12V-14V source (i.e. drill battery). If the awning
does not begin to move, reverse the leads.
2. Remove the battery after the awning is open.
ragm003
Ø 5/16" [8mm] Hole
thru Roof
Align Hole with Edge of Endcap
and Slightly Behind Awning
Tighten Screw to
10 ft-lbs.
[13.6nm]
(3 plcs)
Mounting Bracket
M6 Screw & Square Nut
(3 per awning)
Awning Frame
ragm004
Edge of
Case
Edge of
Case
Center Knuckle
4.5m 60.0" 152cm
5.0m 69.75" 177cm
Outside Connector
2.44m 5.0" 13cm
2.57m 5.0" 13cm
3.0m 3.25" 8cm
3.5m 13.25" 33.5cm
4.0m 13.25" 13.5cm
4.5m 4.0" 10cm
5.0m 14.0" 35cm

F R
E
8
B
N
m
o
Th
th
e
T
o
1.
2.
EESTYLE E
V
O
L
T12 S
Y
w
o
OTICE
o
unted as f
o
For travel
t
a) Install
e
b) Install
e
c) Install
e
any ite
m
d) Installe
d
tied int
o
For motori
z
a) Install
e
e BT12 mo
d
e
vehicle P
C
i) If Ope
n
ii) If tied t
o
iii) If tied t
o
o
Start:
Determine
NOTE: T
h
switches i
s
appropriat
e
Route the
m
L
UTION A WNI
N
Y
STEM I
N
W
ARN
o
rking on o
r
To comp
o
llows:
t
railers and
5
e
d in a dedi
c
e
d with the o
e
d in a cabi
n
m
s or cargo
d
with an int
e
o
the parking
z
ed coache
s
e
d with an in
t
d
ule provid
e
C
M or other
s
n
= Awning
A
o
GND = R
T
o
+12Vdc =
the locatio
n
h
e BT12 co
n
s
greater t
h
e
size wire
g
m
otor cable
N
G
N
STALL
A
ING Sho
c
r
around th
e
ly with 20
1
5
th
wheels:
ated switch
ptional cov
e
n
et with a lat
that may m
e
rrupt circuit
brake or ign
i
s
(Class A,
C
t
errupt circu
e
s an ignitio
n
s
witched so
u
A
ctive
T
L (Retract
T
Standard –
n
for the aw
n
n
trol modul
e
h
an 6", th
e
g
auges. Us
e
and LED h
a
Install
A
TION
c
k Hazard.
e
electrical
1
8 NFPA 1
cabinet wit
h
er
ed bezel a
v
ching door
w
o
ve or shift
d
that disable
s
i
tion that dis
c
C
lass B or
C
it connecte
d
n
lockout o
p
u
rce the foll
o
T
hen Lock)
–
Extend co
m
n
ing switche
s
e
leads are
6
e
installer
m
e
appropriat
e
a
rness to th
e
ation Manu
a
Always di
s
system.
192 RV S
t
h
a latching
d
v
ailable fro
m
w
here the s
w
d
uring trans
s
awning ext
e
c
onnects the
C
lass C):
d
to the “IG
N
p
tion. When
o
wing para
m
–
A
wning re
t
m
mand disa
b
s
, awning li
g
6
" in length.
m
ust furnis
h
e
sized butt
e
location of
a
l
s
connect b
a
t
andard, S
e
d
oor; or,
m
Carefree;
o
w
itch is prot
e
s
it; or,
e
nsion whe
n
BROWN exte
n
N
LOCK” (gr
e
the “IGN L
O
m
eters are s
e
t
racts, exte
n
b
led
g
hts switch
a
If the dist
a
h
splice wi
r
splices to s
e
f
the module
a
ttery or p
o
e
ction 6.4.
7
o
r,
ected and
C
n
the vehicle
n
d wire).
e
en wire).
O
CK” (gree
n
e
t:
n
d comman
d
a
nd BT12 c
o
a
nce betwe
e
r
es for the
e
cure conn
e
.
Carefree
o
07
0
o
wer sourc
e
7
, switche
s
C
ANNOT be a
is in motion
n
wire) is c
o
d
disabled
o
ntrol modul
e
e
n the mod
u
extra dista
e
ctions.
o
f Colorado
0
036-001r3
e
before
s
must be
ctivated by
(i.e. a relay
o
nnected to
e
.
u
le and the
nce. Use

Carefree of Colorado Installation Manual FREESTYLE EVOLUTION AWNING
070036-001r3 9
BT12 CONTROL MODULE INSTALLATION
(Refer to the wiring diagram on page 11.)
NOTICE Do not mount the unit near heat producing elements such as LP appliances or engine
exhaust components.
NOTICE For best reception, do not mount the unit near or on a metal surface.
1. Clean the mounting surface. The surface must be flat and
clean for the mounting tape to properly adhere.
2. Remove the release paper from the tape on the back of the
module and firmly press the module onto the mounting
surface.
NOTE: The module may be oriented for best fit with
access to the wire leads.
3. Attach the motor wires (refer to diagram for corresponding
wire colors) to the module leads for the motor using 14-
16awg butt splices.
4. Run a minimum 14 awg wire to chassis ground.
Suitable ground would be the vehicle chassis or
conductive structure connected to the chassis. Splice
the wire to the module GND lead with a 14-16awg butt splice.
5. Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The
circuit should be protected by a 15-amp fuse. Splice the wire to the module +12V lead with a 14-16awg
butt splice.
NOTE: If the wire run is 30 feet or longer for +12Vdc and/or GND, use 12awg wire to prevent voltage
drop. Use the appropriate butt splices for the wire size.
6. Splice the Black wire from the LED Harness to the module LED GND lead (Black) with a 18-22awg butt splice.
7. Route the module LED + lead (RED) to the awning lights switch location. Use 20awg wire and 18-22awg butt
splice to extend the lead as necessary.
8. Route the module IGN LOCK lead (Green) to the vehicle PCM or other switch source (used for ignition lockout).
9. Route the remaining wires (Violet, Gray, Yellow and Brown) to the location for the awning control switches. Use
20awg wires and 18-22awg butt splices to extend the leads as necessary.
Remove
Release Paper
Mounting
Tape
BT003

FREESTYLE EVOLUTION AWNING Installation Manual Carefree of Colorado
10 070036-001r3
AWNING SWITCH INSTALLATION
(Refer to the wiring diagram on page 11.)
1. At the switch location cut a 2.32" x 1.5" hole.
2. From the module, terminate the three (3) 20awg
wires (Brown, Yellow and Gray) with .187, 18-20
awg female terminals. Attach to the
EXTEND/RETRACT switch as shown in the wiring
diagram.
3. From the module, terminate the Violet wire with a
.187, 18-20 awg female terminal. Attach to the
ON/OFF switch.
4. Run a minimum 14 awg wire to +12VDC. Terminate
the wire with .187, 14-16 awg female terminal and
connect to the second terminal of the ON/OFF switch.
NOTE: If the wire run is 30 feet or longer, use
12awg wire to prevent voltage drop. Use the
appropriate wire terminals for the wire size.
5. Push the wires and switches into the hole then attach the switch frame using 4 #6 x 1/2" screws.
6. Snap the switch bezel over the switch frame.
AWNING LIGHTS SWITCH INSTALLATION
NOTE: Installers may choose to furnish the control switch or may wire directly to a multiplexing control
center.
1. Determine the location of the switch.
2. At the switch location, cut a 1.13" x 1.5" hole.
3. Wire the switch as shown. Wire terminals at the switch are .187, 18-24 awg female disconnects.
4. Press the wires and switch into the mounting hole. Secure the switch using two (2) #6 x 1/2" screws.
5. Snap the switch bezel over the switch frame.
2.9"
1.13"
1.88"
#6 x 1/2 " Screw (x2)
BT004d
Single Pole, Single Throw Switch
Multiplexing Control Connection
White/Violet (20awg)
To +12VDC
White/Violet (20awg)
To Multiplexing
Controller
ON
OFF
1.5"
1"
BT001
2.32"
1.5"
#6 x 1/2" Screw (x4)
RETRACT
ON
EXTEND
OFF
Awning Control
RETRACT
ON
EXTEND
Awning Control
OFF
Optional
Covered Bezel

Carefree of Colorado Installation Manual FREESTYLE EVOLUTION AWNING
070036-001r3 11
WIRING DIAGRAM
Extend/
Retract
On/Off
Rear View of
Switch Assy
.187, 18-20awg Female
Spade Terminals (x5)
To +12VDC
GND
Black
Red
LED Strip
Violet
Green
Black
(16awg)
Red (16awg)
Control Module
To vehicle PCM
or other switched source
White (16awg)
Blue (16awg)
White/Red (20awg)
White/Black (20awg)
(18awg)
Red
(18awg)
(18awg)
Single Pole, Single Throw Switch
Gray
Brown
(18awg)
(18awg)
3
2
1
4 5
BT002ragm
A
B
DETAIL B
Awning Lights Switch Options
DETAIL
A
Motor Connect
Dry Connectors
Direct Motor Control
Tubular Motor RHTubular Motor LH
Right Angle Gear Motor (typical for LH and RH Installations)
To +1 2 VDC
Yel low
(18awg)
White/Violet (20awg)
To +12VDC
White/Violet (20awg)
White/Violet (20awg)
To +12VDC
Multiplexing Control Connection
To Multiplexing
Controller
Violet
Green
(18awg)
(18awg)
Gray
Brown
(18awg)
(18awg)
Yellow
(18awg)
M1
M2
Violet
Green
(18awg)
(18awg)
Gray
Brown
(18awg)
(18awg)
Yellow
(18awg)
S1
S2
Com
To vehicle PCM
or other switched source
3To vehicle PCM
or other switched source
3
+12VDC
Awning Disable
Switch
+12VDC
Awning Disable
Switch
6 6
C
DETAIL C
Multiplex Control System
White
Blue
MOTOR
Brown
Blue
Brown
Blue
Brown
Blue
Brown
Blue
White
Blue
MOTOR
F
F
Black Red
F
F
F
F
Black
Red
F
F
Limit Switch
Limit Switch
Green
Orange Yellow
White White
Blue
MOTOR
F
F
Black Red
F
Limit Switch

FREESTYLE EVOLUTION AWNING Installation Manual Carefree of Colorado
12 070036-001r3
For GND, run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis
or conductive structure connected to the chassis.
For +12Vdc, Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or
equivalent. The circuit should be protected by a 15-amp fuse.
NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the
appropriate wire terminals for the wire size.
The BT12 module leads are 6" in length. If the distance between the module and the switch is
greater than 6", the installer must furnish splice wires for the extra distance. Use appropriate size
wire gauges. Use appropriate sized butt splices to secure connections.
The BT12 module provides an ignition lockout option. When the “IGN LOCK” (green wire) is
connected to the vehicle PCM or other switched source the following parameters are set:
a) If Open = Awning Active
b) If tied to GND = RTL (Retract Then Lock) – Awning retracts, extend command disabled
c) If tied to +12Vdc = Standard – Extend command disabled
The LED connection is optional to provide LED controls through the app for white LEDS only.
White LEDS can also be installed per the standard LED installation without BT12 Controls. RGB
lights must be installed per the standard RGB installation.
Carefree LED lights uses a 2 amp circuit draw. The BT12 limits the output current to 2 amps. If
using a different brand of high output LED’s that draws more than 2 amps, the lights will flicker
and not perform as expected.
The awning disable switch is a single throw; single pole switch used with OEM Multiplexing
Control Systems. Switch is furnished by installer.
1
2
3
4
5
6

C
a
07
S
E
N
O
us
e
N
u
n
N
O
s
w
dir
e
Th
U
s
1.
2.
3.
4.
U
s
1.
2.
3.
4.
N
O




Th
w
w
a
refree of Co
l
0036-001r3
E
TTING T
H
O
TE: Kits
a
e
d for repla
c
OTICE
n
ique to ea
c
O
TE: The ill
w
itches or in
c
e
ctions are
v
ere are two
m
s
ing the Awn
in
Turn powe
Extend th
e
completel
y
Retract th
e
When the
a
seconds.
s
ing the Swi
t
Turn the
switch to
O
Press and
switch.
While hol
switch, t
u
switch ON
.
Continue t
switch for
release.
O
TES:
The awnin
g
The BT12
Repeat the
Refer to th
smart pho
n
Multiple d
e
oOnly o
n
oOnly o
n
oMultipl
e
active
a
e “BT12 In
w
w.carefree
o
l
orado
H
E S YST
E
a
re paired a
c
ements mu
Ensure th
a
c
h control
m
ustration sh
o
c
orporate th
e
v
alid for all c
o
m
ethods to s
e
in
g Retract F
u
r to the awn
e
awning.
N
y
.
e
awning.
a
wning is fu
t
ches:
awning
O
FF.
hold the
e
ding the
e
u
rn the
.
o
hold the
e
3 seconds
g
will remai
n
control mod
u
pairing for e
a
e Carefree
C
n
e or tablet)
.
e
vices can b
e
n
e active B
T
n
e active B
T
e
mobile de
v
a
t a time.
stallation
M
o
fcolorado.
c
E
M INTO
P
t
the factor
y
st be paired
a
t the kits
a
m
odule.
o
ws the stan
e
power and
nfigurations.
e
t the syste
m
u
nction
:
ing ON.
N
ote that th
e
lly retracted
power
e
xtend
e
xtend
power
e
xtend
, then
n
in pairing
m
u
le will pair
t
a
ch addition
a
C
onnects M
o
.
e
paired to
t
Motion Sen
Remote ca
n
v
ices (smar
t
M
anual” and
c
om/connect
Install
P
AIRING
M
y
for simplifi
to the exist
a
re kept tog
dard Carefr
e
Extend/Ret
r
m
into pairing
e
awning d
o
, press and
m
ode for 5
m
t
o the physi
c
a
l device (th
e
o
bile App m
t
he awning
u
sor can be
p
n
be paired
t
t
phone or ta
“Caref
r
ee
s.
ation Manu
a
M
ODE
ed installati
o
ing control
m
ether and
n
e
e switches.
r
act controls
mode.
o
es not ha
v
hold the re
t
m
inutes.
c
ally closest
e
module re
m
anual for s
e
u
p to a maxi
m
p
aired to the
t
o the BT12
C
blet) can b
e
Connects
M
a
l
on. Separ
a
m
odule.
n
ot mixed
w
Some OE
M
in a multipl
e
v
e to be op
e
t
ract switch
f
unpaired d
e
m
embers the
e
tting up an
d
m
um of 8 p
e
BT12 Cont
r
Control Mo
d
e
paired to t
h
M
obile App
F REE
S
a
te compon
e
w
ith other
k
M
’s may cho
o
e
xing control
e
ned
f
or 3
e
vice first th
e
devices that
d
pairing a s
m
e
ripheral de
v
r
ol Module.
d
ule.
h
e BT12 M
o
Manual” a
r
S
TYLE E VOLU
T
e
nts that ar
e
k
its. The p
a
o
se to furni
s
system. T
h
e
n go to wo
r
have been
p
m
art device
v
ices.
o
dule but on
l
r
e available
T
ION A WNING
13
e
added or
a
irings are
s
h their own
h
e following
r
king mode.
p
aired).
(such as a
l
y 1 can be
on-line at

FREESTYLE EVOLUTION AWNING Installation Manual Carefree of Colorado
14 070036-001r3
PITCH ADJUSTMENT
The awning opens and closes with a steep pitch. On low profile vans, the leading edge of the awning may
hit the top of the sliding door if the door is open while extending or retracting the awning. To prevent this,
the lower limit of the pitch can be adjusted upwards.
1. Open the awning to access the screws located on the side of the arm case knuckles.
2. For Original Configurations:
2.1. Using an 8mm allen wrench, loosen the 2 screws on the side of
the case connector.
2.2. Have a second person lift the lead rail to the desired height.
2.3. When the pitch is set at the desired angle, tighten the screws.
Torque to 50 ft-lbs.
3. For Current Configurations:
3.1. Loosen the screw on the side of the case connector.
3.2. Turn the 10mm (5mm allen wrench) clockwise to raise the pitch
or counterclockwise to lower the pitch.
Tip: When raising the pitch have a second person lift up on the
lead rail.
3.3. When the pitch is set at the desired angle, tighten the screw.
Torque to 25-30 ft-lbs.
4. Repeat for each arm. Ensure that the lead rail is parallel with
the awning case.
NOTE: The lead rail is self-adjusting. No adjustment is required to the lead rail when the pitch is changed.
ADJUSTING THE EXTEND LIMIT
The extend limit switch disables the extend function when the awning is fully extended. This prevents the
awning from overextending and can be adjusted so that the canopy is tight when the awning is extended.
The switch is located on the arm knuckle closest to the motor
(i.e. right knuckle for RH motor, left knuckle for LH motor).
To adjust the extension:
1. Open the awning to access the switch.
2. Loosen the screw.
3. Move the switch toward the arm to decrease the extension.
4. Move the switch away from the arm to increase the extension.
MANUAL OVERRIDE
If power to the vehicle is not available, the awning can be safely retracted using the manual override
located on the idler end of the case.
NOTE: This procedure cannot be used to extend the awning.
1. Remove the outer endcap on the idler side and save.
2. Insert a 3/8" socket drive extension and handle into the
square drive hole inside the inner end cap.
3. Turn the handle to match the direction arrows until the
awning is retracted.
4. Replace the outer cap.
NOTICE After closing the awning with the manual override, the lead rail may move out from the
case 1/4" -1/2". This is normal and the awning is secure for travel until power is restored or repairs
are completed. Do not attempt to force the lead rail in with the override, serious damage can occur
to the awning.
ragm006
3/8" Socket
Drive Extension
Remove
Cover
ragm007
IncreaseDecrease
Extend Limit Switch
Loosen Screws to
A
djust
Tighten to 50 ft-lbs. When Finished
ragm005
Current Configuration
Original Configuration
Loosen Screw to Adjust
Tighten to 25-30 ft-lbs. When Finished
Adjustment Screw
Lower Raise