Carefree PARAMOUNT User manual

052548-301r13 Printed in USA November, 2018
S ERVICE M ANUAL
PARAMOUNT
2-Stage Multi-Position Awning
RV
Read this manual before servicing this product. Failure to follow the instructions and
safety precautions in this manual can result in personal injury and/or cause the product to
not operate properly.
For LED replacement parts and service procedures refer to 070013-301 “LED Service Manual for
Box Awnings” available on-line at www.carefreeofcolorado.com

P ROPRIETARY S TATEMENT
The Paramount Awning is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The
information contained in or disclosed in this document is considered proprietary to Carefree of Colorado.
Every effort has been made to ensure that the information presented in the document is accurate and
complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result
from the use of this document.
The information contained in this manual pertains to the current configuration of the models listed on the
title page. Earlier model configurations may differ from the information given. Carefree of Colorado
reserves the right to cancel, change, alter or add any parts and assemblies, described in this manual,
without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado
products only. Any other reproduction or translation of this document in whole or part is strictly prohibited
without prior written approval from Carefree of Colorado.
S AFETY I NFORMATION
This is the safety alert symbol. It is used to alert individuals to potential
personal injury hazards. Obey all safety messages that follow this symbol to
avoid possible personal injury or death.
WARNING
Indicates a hazardous situation, which if not avoided, could result in death or
serious bodily injury.
CAUTION
Indicates a hazardous situation, which if not avoided, may result in minor or
moderate bodily injury.
NOTICE
Indicates a situation that may result in equipment-related damage.
General Safety:
WARNING This product can expose you to chemicals including Di-isodecyl phthalate
(DIDP), Vinyl Chloride and Formaldehyde, which are known to the state of California to cause
cancer or birth defects or other reproductive harm. For more information visit
www.P65warnings.ca.gov
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
WARNING Always wear appropriate safety equipment (i.e. goggles).
CAUTION Always use appropriate lifting devices and/or helpers when lifting or
holding heavy objects.
NOTICE When using fasteners, do not over tighten. Soft materials such as fiberglass and
aluminum can be "stripped out" and lose the ability to grip and hold.
Carefree of Colorado www.carefreeofcolorado.com a Scott Fetzer company
Electric components in this product have been tested by the following agencies:
Motor: UL Recogonized (USA)
CSA Approved (Canada)
Controls: UL Listed (USA & Canada)

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 1
TABLE OF CONTENTS
Product Overview..........................................................................................................................2
Paramount Patio Awning Specifications .............................................................................................2
Standard System Adjustments ....................................................................................................3
Setting the Motor Limits..........................................................................................................................3
OUT Limit Switch ................................................................................................................................3
IN Limit Switch ....................................................................................................................................3
Awning Calibration Procedure................................................................................................................4
Procedure............................................................................................................................................4
Adjusting the Lead Rail...........................................................................................................................6
Adjusting the Lead Rail Height............................................................................................................6
Adjusting the Horizontal Lead Rail Position........................................................................................6
Manual Override.....................................................................................................................................7
Programming the RF Receiver for a Remote .........................................................................................8
Standard Maintenance............................................................................................................................9
Fabric Care .........................................................................................................................................9
Mildew.................................................................................................................................................9
Pooling................................................................................................................................................9
Arm Care.............................................................................................................................................9
Arm Noise ...........................................................................................................................................9
Canopy Replacement..................................................................................................................10
Motor Replacement.....................................................................................................................11
Modifying the Top Cover.......................................................................................................................13
Short Spring Arm Replacement .................................................................................................14
Removing the Existing Arm...............................................................................................................14
Installing the New Arm......................................................................................................................15
Long Spring Arm Replacement..................................................................................................16
Removing the Existing Arm...............................................................................................................16
Installing the New Arm......................................................................................................................16
Removing the Awning.................................................................................................................17
Diagnostic Tests..........................................................................................................................18
Common Operation Items.....................................................................................................................18
Testing the System...............................................................................................................................19
Electronics...................................................................................................................................23
Wiring Diagram – Single Awning..........................................................................................................23
Wiring Diagram – 2-Awnings................................................................................................................24
Phone Cord Connection....................................................................................................................25
Wiring Diagram – 4 Awnings ................................................................................................................26
Connection Flex w/ "110VDR" Control Boxes ......................................................................................28
Optional Manual Bypass Switch...........................................................................................................28
Sensor Replacement............................................................................................................................29
Part Number Listing....................................................................................................................30
Serial Number/Part Number Location...................................................................................................30
Illustrated Parts List..............................................................................................................................30
Electronic Components.....................................................................................................................32

PARAMOUNT Service Manual Carefree of Colorado
2 052548-301r13
PRODUCT OVERVIEW
The Paramount Patio Awning offers the coach owner an awning system that provides as much or as little
shade as required. The canopy is housed in an aluminum case that easily blends in with the coach roof.
Each unit is equipped with lateral support arms that are the strongest available on the market. No vertical
arms interfere with coach sidewalls or equipment that may be mounted on the roof.
The unique and innovative 110V electronic control system provides Carefree’s Direct Response system with
interior pushbutton controls for standard extend/retract functions. At the master control panel the auto-retract
system can be engaged to automatically retract the awning in windy conditions. Sensitivity can be set to respond
to a variety of wind speed conditions. An RF remote is furnished with the Direct Response system.
Paramount Patio Awning Specifications
The following information is for reference only.
LENGTH 14’ – 21’ (in 1 foot increments)
Position: Slide-Out Window Patio
EXTENSION: 40" 72" 106"
LEAD RAIL DROP 6" (20°) 32" (33°) 51" (33°)
Values are approximate, actual dimensions may vary with specific installations.
Angles are measured from horizontal (parallel to ground)
MOTOR SPECIFICATIONS:Available in LH or RH configurations
Type: Tubular Motor
Power: 120V, 60HZ, 2.5A
Torque: 60 nm
Speed: 14 RPM
Cycle: 40 Sec ON / 1 Min OFF
CONTROLS: Direct Response Electronics with a single master control and single remote for all awnings.
COLOR: Hardware: White, Black
Fabric: Woven Acrylic Fabric
APPROXIMATE INSTALLED WEIGHT (LBS.)
Awning Length (ft.) Weight Awning Length (ft.) Weight Awning Length (ft.) Weight
14 195 17 227 20 258
15 212 18 234 21 266
16 220 19 246
Optional factory installed 12V LED lighting is available for the Paramount awning. LED lighting requires a
separate 12V control switch.
There are two configurations of the Paramount based on
the canopy construction as shown.
7.13”
12.75”
A (Awning Length)
Paramount001
Top View Profile
HS Configuration
Canopy construction with
horizontal seams
VS Configuration
Canopy construction with
vertical seams
Mirage056

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 3
STANDARD SYSTEM ADJUSTMENTS
SETTING THE MOTOR LIMITS
The “OUT” limit switch is used to stop the motor when the awning is fully extended. The “IN” limit is NOT
USED with the Direct Response system (see description below).
OUT Limit Switch
1. Extend the awning out completely.
2. Confirm that the arms are fully extended. The motor should stop and the fabric should be tight. If the
motor continues to run, the fabric will sag; or, if the motor quits before the arms are fully extended, it will
be necessary to adjust the “OUT” limit switch.
NOTE: It is best to make the adjustments in increments of a single turn. 3 full turns of the screw
equals approximately 2” of fabric extension.
3. If the fabric sags:
3.1. Retract the awning until the fabric is tight then retract an addition 10"-12".
3.2. Using a 4mm Allen wrench turn the “OUT” limit switch to reduce the time the motor runs.
3.3. Extend to confirm that the adjustment is correct.
3.4. Repeat the procedure until the awning extends correctly.
4. If the arms do not extend completely:
4.1. Retract the awning approximately 10"-12".
4.2. Using a 4mm Allen wrench turn the “OUT” limit switch to increase the time the motor runs.
4.3. Extend to confirm that the adjustment is correct.
4.4. Repeat the procedure until the awning extends correctly.
IN Limit Switch
NOTE: The “IN” limit switch is not adjusted with the Direct Response system. The system electronics
monitors the motor and shuts the motor off when the awning is fully retracted.
If the IN limit switch is accidentally adjusted, the motor may shut off before the awning is fully closed. If this occurs,
turn the "IN" adjustment screw to INCREASE the motor run time. It is not necessary that the screw matches the
closed position.
NOTE: It is normal for the lead rail to slightly relax after the awning closes completely.
NOTE: There are three (3) motor limit switch configurations.
Visually inspect the limit switches to determine which
configuration is installed in the awning. Use the illustrations
to determine the correct turning direction for adjustments.
The limit switches are located inside the case, near the end plate.
To access the switches, remove the rubber plugs on top of the
case next to the end plate.
Paramount014
Configuration 1
(Discontinued)
Configuration 2
(Inactive)
Configuration 3
(Current)
Configuration 1
(Discontinued)
Configuration 2
(Inactive)
“IN”
Limit Switch
4mm Allen Head
“OUT”
Limit Switch
4mm Allen Head
LH Motor RH Motor
Lead Rail
“IN”
Limit Switch
4mm Allen Head
“OUT”
Limit Switch
4mm Allen Head
Increase
Run Time
Decrease
Run Time
Increase
Run Time
Decrease
Run Time
Increase
Run Time
Decrease
Run Time
Increase
Run Time
Decrease
Run Time
Configuration 3
(Current)
Decrease
Run Time
Increase
Run Time
Decrease
Run Time
Increase
Run Time

PARAMOUNT Service Manual Carefree of Colorado
4 052548-301r13
AWNING CALIBRATION PROCEDURE
If the awnings do not align at the intermediate positions (slide-out and window), it is necessary to run a
calibration routine to adjust the run and stop times for the awning.
1. The controls are programmed with default awning calibration values; this allows full awning operation
out-of-the-box.
2. The default calibration values are based on the average run times for the Paramount awning; these
values are close but not perfect.
3. The Slide-Out Cover and Window awning intermediate positions are set as a percentage of the awning
run time, 29% for Slide-Out Cover and 70% for Window.
4. Performing an awning calibration collects the actual extend and retract run times to allow the most
accurate awning operation.
5. For multiple awning installations, adjacent awnings must be aligned in the full extension position before
initiating awning calibrations, otherwise, a calibration will lock-in the difference in run times and will
cause misalignment at the intermediate positions.
6. For multiple awning installations, it is recommended that all awnings be calibrated at the same time
while operating on the same power source, i.e. do not calibrate one awning while operating on the
inverter and another while operating on the generator.
7. If a calibration is started and fails (stops) for any reason, the system resets the travel time and
maximum run time to the default values.
Procedure
Prior to starting the procedure, ensure that the motor limits are set correctly (refer to page 3).
The IN limit switch must be set to allow the motor to stall. Calibration will fail if the switch is set to stop
the motor.
The OUT limit switch is used to align adjacent awnings in the fully extended position before initiating
awning calibrations, otherwise, a calibration will lock-in the difference in run times and will cause
misalignment at the intermediate positions.
NOTICE Do not continuously operate the awning more than 2-3 cycles maximum. The motor is
equipped with a thermal protection circuit to protect the motor from overheating. Operating the awning
repeatedly over a short time period may cause the circuit to sense an overheat condition and shut off the
motor. If this occurs, wait approximately 15 minutes to allow the motor to cool then resume the
procedure.

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 5
NOTE: 4-awning keypad and remote shown. Description and procedures apply to all configurations.
1. Ensure that power is available to the awning control system.
2. Turn the system power on at the keypad.
3. To initiate calibration mode: At the keypad, Press and Hold the two lower value buttons of the
sensitivity settings for a full 5 seconds.
When the system is in calibration mode, the system status LED will flash and the four (4) sensitivity
setting LEDs will illuminate as steady ON.
The system will remain in calibration mode for 30 seconds. If an awning is in the calibration cycle
when the 30 second window expires, the awning will complete the calibration.
In calibration mode, all functions except for the "Patio" and "Stop" commands are disabled.
If the "Stop" button is pressed during a calibration, all awning calibrations are halted immediately
and the system returns to normal operation. The calibration mode must be reinitialized to continue.
Any awnings that were stopped partially through a calibration will be reset to the default values.
In calibration mode, any or all awnings can be calibrated and/or re-calibrated.
4. At the keypad or on the remote, press and release the "Patio" button to start the calibration for the
selected awning.
The awning will partially extend then retract to determine the full retract position. Next, the awning
will cycle to the full extend (patio position) then retract to the fully closed position. When the awning
has returned to the fully retracted position, the individual awning calibration is complete. Repeat for
each awning installed.
For multiple awning installations, it is not necessary to wait for one awning to complete the
calibration cycle before starting the next awning calibration.
In calibration mode, pressing the "Patio" button for an awning that has been calibrated will cause
the awning to recalibrate.
P OWER
#1 #2
Power
On/Off
Motion Sensor
High
Stop
#3 #4
S TOP
System Status
LED
#2 #3
Stop
#1 #4
Awning
Control
P ATIO
(Full Extend)
Press & Hold
for 5 seconds
Motion Sensitivity Setting
LEDs on Steady
in Calibration Mode
KeyPad Remote
S
TOP
Low
Paramount012

PARAMOUNT Service Manual Carefree of Colorado
6 052548-301r13
ADJUSTING THE LEAD RAIL
Adjusting the Lead Rail Height
The Paramount arms are installed and adjusted at the factory to operate at the tallest height possible. For multiple
awning installations, the lead rails of adjacent awnings may appear to not align because of installation variables.
The height of the high lead rail may be lowered with the procedure below. This is not a pitch adjustment.
Maximum height adjustment is approximately 6 3/8".
1. Fully extend the awnings.
2. On the middle rail, locate the long arm knuckle
closest to the adjacent awning.
3. Loosen the securing screws located on the outside
of the knuckle. DO NOT remove these screws.
4. Turn the adjustment screw counter clockwise to
lower the lead rail. Turn the screw in increments of
1/2 turn until the lead rail matches the adjacent
awning lead rail.
Tip: If the screw is hard to turn, have a second person lift up on the lead rail, then turn the screw and
let the lead rail down. Repeat until the lead rail is at the desired height.
5. Tighten the securing screws 30-33 ft-lbs.
Adjusting the Horizontal Lead Rail Position
The following procedure is to adjust the horizontal position of the lead rail when the rail is not centered in
the case when the awning is closed. This is only necessary if the end plate of the lead rail is rubbing or
hitting the end plate of the case.
This procedure is for early models of the Paramount. On newer versions, the lead rail connectors are
staked in position to prevent possible shifting and cannot be adjusted
1. (Detail A) With the awning closed as
much as possible measure the distance
between the inside of the case end
plate and the outside of the lead rail end
plate. The distance should be
approximately 1/4". Note the difference
between the actual measurement and
the standard 1/4" spacing. This is the
amount of adjustment required.
Example: If the lead rail overlaps the
end plate by 1/8", the difference is
1/8" + 1/4" = 3/8" difference.
2. Extend the awning out just past the slide-out position. The long arms should be slightly extended to
allow access to the lead rail connector.
3. Mark the location of the lead rail connectors for reference then loosen the setscrews that hold the
connectors in place.
4. Move the connectors the distance measured in step 1 and tighten the set screws.
NOTE: To adjust the lead rail in one direction, move the connectors in the opposite direction. For
example to shift the lead rail to the right, move the connectors to the left.
NOTICE BOTH connectors must be moved the same distance and direction.
5. Test by closing the awning. Repeat if necessary.
B
DETAIL B
Lead Rail
Paramount022
Lead Rail
Connector Set Screw (x2)
1/4” Approx.
Lead Rail
End Plate
DETAIL A
A
Long Arm (ref)
Adjustment Screw
Securing Screws
Middle Rail (ref)
Paramount013

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 7
MANUAL OVERRIDE
If 110V power is not available to the coach, the Paramount awning can still be safely retracted using the
manual override.
1. The bypass is located inside the case, near the end cap. Remove the large rubber plug on top of the
awning located toward the rear of the case on the motor side.
2. Chuck the 7mm hex key into a 3/8” battery powered drill.
3. Insert the hex key into the manual override on the awning.
4. Operate the drill in the direction shown in the diagram to close the
awning. Reverse the drill to open the awning.
5. When done, reinsert the rubber plug.
7mm Hex
RTA015a
LH Motor RH Motor
Lead Rail
Open
Close
Open
Close

PARAMOUNT Service Manual Carefree of Colorado
8 052548-301r13
PROGRAMMING THE RF RECEIVER FOR A REMOTE
When adding or replacing a remote control, it is necessary to program the transmitter and receiver.
1. Power to the control box must be on.
2. Locate the receiver box.
3. Press and release the “Press to Learn Transmitter” button on the bottom of
the receiver box. The receiver is in program mode when the red light comes
on.
4. Press and release any button on the remote, it is recommended to use the
stop button. The red light will go out after the receiver learns the remote
signal.
NOTICE Any button on the remote may be pressed. When the
receiver learns the transmitter signal the system will perform the operation
of the button pressed. Example: Pressing an "Extend" button during the
learning phase will cause the awning to extend when the receiver learns
the signal. Use caution to avoid unexpected movement by the awning.
5. Repeat for each additional remote.
OPERATIONAL NOTES:
a. Transmitter and receiver operate on a frequency of 433MHz.
b. The receiver exits the program mode after ten seconds.
c. If the light does not come on in step 2, check the continuity of the cord between the boxes and repair or
replace as required. Pin 1 of the 1st connector goes to pin 1 of the 2nd connector etc. If the light still does not
come on, the memory is full and must be cleared.
d. If the light does not go out in step 3, the receiver already knows the transmitter's signal or the battery in
the remote needs to be replaced.
e. To clear the memory: PRESS AND HOLD the transmitter learn button. While holding the button, the
indicator light should be OFF for the full 5 seconds then come on.
f. The system may be programmed for up to 5 remotes. Additional remotes may be ordered separately.
Program
Button
Indicator
Light
WS018
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 9
STANDARD MAINTENANCE
Maintaining a Carefree Awning is easy. Just follow these basic steps:
Always operate the awning according to the instructions.
Periodically check that the fasteners are tight. Tighten if necessary.
Keep the awning fabric and arms clean.
Fabric Care
NOTICE Do not use oil based cleaners or any caustic, granulated, or abrasive type cleaners
on your Carefree product.
1. One of the best ways to keep the fabric looking good and to delay the need for deep or vigorous
cleanings is to hose fabrics off on a monthly basis with clear water. This practice will help prevent dirt
from becoming deeply imbedded in the fabric. In most environments, a thorough cleaning will be
needed every two to three years.
2. When it’s time for a thorough cleaning, the fabric can be cleaned while still on the awning frame.
For Vinyl Fabric – Use a soft brush and warm water with soap.
For Acrylic Fabric – Use a stiff brush and warm water with soap.
3. When cleaning the fabric, it is important to observe the following:
Always use a natural soap, never detergent.
Water should be cold to lukewarm, never more than 100F.
Air-dry only. Never apply heat to the fabric.
Always allow the fabric to dry thoroughly before rolling up the awning.
Mildew
Mildew is a fungus growth that looks like dirt. Vinyl coated polyester fabrics are mildew resistant because
of a chemical biocide in the vinyl coating. Under ordinary conditions, mildew will not appear. However, in
areas where high temperature and humidity are common, mildew can be a problem and required the
material to be washed more frequently. Thoroughly rinse the fabric with clean water and allow to air dry
completely before rolling up the awning.
Pooling
When water collects on the top of the fabric, this is known as "pooling". This can occur during inclement
weather or if a running air conditioner discharges over the awning. The water is dumped when the awning
is retracted. It is recommended that if water accumulates on the top; retract the awning in steps (8"-12") to dump
the water. This will help prevent the fabric from stretching or distorting.
The effects of wind and rain on an awning are unpredictable. Severe damage to the awning and the
vehicle may result. IF WIND OR EXTENDED PERIODS OF RAIN ARE EXPECTED,ROLL UP THE AWNING AND
SECURE FOR TRAVEL.
Arm Care
The best method of keeping the arms operating smoothly is to clean them. Dirt and debris can cause the
channels not to pivot easily.
Periodically wash the channels with running water (i.e. a hose) to keep them
clean. If the joints do not flex easily, lightly spray the pivot pins with a dry
silicone lubricant, after the arms have been cleaned and dried thoroughly.
Arm Noise
After a period of use, the arm knuckle joints may slide together slightly
making a squeaking or squealing noise; this is normal and not a reason for
concern. To reduce the sound, apply a few drops of light oil (3 in 1 or
equivalent) on the knuckle joint seams. Allow some time for the oil to
penetrate into the joint.
Joint Seam
Light Oil
Paramount023

PARAMOUNT Service Manual Carefree of Colorado
10 052548-301r13
CANOPY REPLACEMENT
During the following instructions, use the manual override procedure on page 6 to open and close the awning.
1. Disconnect power to the awnings.
2. Open the awning to be serviced 18"-24" inches to expose the arm
elbows.
3. Using a minimum 1/2" rope, firmly tie the elbows of the outer spring
arms together, do not use bungee cords. When tying the rope, use a
non-slip knot such as a square knot or equivalent.
4. Use rope or heavy duty plastic ties (3/8" x 12") to tie the long arms and middle rail together in the closed
position.
CAUTION Failure to secure the arms as described will allow the spring arms to extend out
possibly causing personal injury and damage to the awning.
5. Remove the two fabric retainer screws on both ends of the lead rail and set aside.
6. Remove the top screws holding the top cover. Rotate the top cover back and out of
the way. If rotated back without obstructions, the top cover will disengage from the
pivot rail and can be set aside.
7. Use the manual override (page 7) to unroll the canopy until the fabric slot is exposed on top of the roller tube.
8. Remove the access plug from the top of the idler end plate.
8.1. For one-piece end plates, it is necessary to remove the idler end plate and set aside.
NOTE: It will be necessary to support the roller tube, do not allow the roller tube to pull off the motor.
9. From the idler side, slide the old canopy out of the roller tube and lead rail.
10. Inspect the slots in the roll bar and lead rail. Clean and deburr as required. Lightly spraying the inside
of the slot with a dry silicone lubricant will aid in sliding the new fabric in.
11. Slide the new canopy into the lead rail and
roller. Both edges must be done at the
same time. Orient the fabric so that the
large polycord goes into the lead rail, the
smaller polycord goes into the roll bar.
The hem should be on the down side.
12. The canopy should be approximately .25"
from the end of the motor crown.
13. If previously removed, attach the end plate
to the case with the roller tube idler seated
into the bearing.
14. On the idler side, stake the canopy with
one (1) #8 x 1" flat head screw. The
screw goes through the material, polyrod
and roller tube in the fabric slot.
15. Use the manual override to roll the canopy onto the roller tube, the material rolls over the top of the roll bar.
Ensure the fabric rolls evenly onto the roller tube.
16. Once the fabric is snugly rolled up, remove the rope used to secure the arms previously.
17. Restore power to the awning.
18. Extend and retract the awning. Adjust the canopy in the lead rail as required.
19. Install the fabric retainer screws in the lead rail.
20. It may be necessary to adjust the motor limits. Refer to page 3.
21. Install the top cover.
Tie the Elbows of the
Outer Short Arms
Tie the Middle Rail
and Long Arms in the
Closed Position Paramount039
Paramount016a
Retaining
Screw (x2)
End Plate
Paramount016
Retaining Screw
(idler side only)
Fabric Slot
Fabric Slot
Retaining Screw
(idler side only)
Fabric
Slot
A
ccess
Plug
Current Configuration One Piece Endplate
.25"
Motor
Roller Tube
Canopy
Retaining Screw
(idler side only)

Carefree of Colorado Service Manual P ARAMOUNT
052548-301r13 11
MOTOR REPLACEMENT
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
Important Note: The current replacement motor has a slightly different configuration for the limit switch locations.
The new motor is orange and has different graphics around the limit switches (see page 3 for comparison). If
replacing an older configuration motor, it will be necessary to modify the top cover limit switch access holes. This
modification should be done prior to removing and replacing the motor to avoid damaging the new motor. See “
Modifying the Top Cover” on page 13.
This procedure requires a minimum of two people.
For multiple awning installations where the awnings are mounted end to end it will be necessary to move the
unaffected awning if the motors are next to each other.
1. Disconnect power to the awning(s).
2. To move an adjacent unaffected awning:
2.1. Close the awning if open.
2.2. Loosen the retaining bolts in the back of the mounting plates.
2.3. Slide the awning away from the other awning; allow a minimum
of 6" to 8" between awnings.
2.4. Temporarily tighten at least one of the retaining screws.
Replacing the motor:
1. Disconnect power to the awning.
2. Disconnect the motor wires at the junction box or control box and pull the cable out.
3. Use the manual override (refer to page 7) to over extend the awning. The arms should be extended
completely, the canopy should be relaxed and the fabric slot of the roller tube should point up.
4. Remove the top screws holding the top cover. Rotate the top cover back and out of the way. If rotated
back without obstructions, the top cover will disengage from the pivot rail and can be set aside.
5. Remove the attaching screws for the end plate then carefully pull the end plate and motor partially out
from the awning case.
6. Remove the screws and nuts holding the motor to the end plate. Set the end plate aside. Note the
orientation of the motor then pull the motor, crown and drive out of the roller tube.
Note: For the HS configuration: When the crown is removed the canopy edge with the polyrod will be
exposed and extend past the roller tube.
7. For HS configuration: Remove the crown from the old motor. This will be used with the new motor.
The crowns are configuration specific.
Paramount017a
HS Configuration End Plate
Motor Screws (x4)
End Plate Screws (x4)
Roller Tube
Motor
Drive Crown Drive Key
Retaining Ring
Exposed Polyrod
VS Configuration
Roller Tube
Motor
Drive Crown Drive Key
Retaining Ring
Paramount017
Retaining Bolt (ref)
Mounting Bracket (ref)

PARAMOUNT Service Manual Carefree of Colorado
12 052548-301r13
8. Assemble the new motor:
NOTE: The new and old motor components are not interchangeable.
8.1. Slide the crown onto the motor.
NOTE: For VS configurations, use the new crown that is included with the motor. For HS
configurations, discard the included crown and use the existing crown that was removed previously.
8.2. Place the drive key into the slot of the motor shaft and slide the new drive onto the motor shaft
and over the drive key.
8.3. Secure the drive using the supplied retaining ring.
9. Attach the new motor assembly to the end plate using the new screws and nuts provided.
10. Slide the new motor assembly into the roller tube. Ensure that the motor drive gear and crown are
properly seated inside the roller tube.
NOTICE For the HS configuration: When the crown is seated in the roller tube, the canopy
edge with the polyrod must be in the fabric groove of the crown.
11. Route the motor cable through the access hole in the back of the case.
12. Ensure the roller tube idler plug is seated in the glide bearing.
13. Position motor end plate on the case and attach using the screws removed previously.
14. Route the new motor wire into the coach and attach (refer to wiring diagrams on page 20 for the
appropriate control system). Ensure that the wire colors match (i.e. red to red and black to black). All
wiring must conform to NEC (National Electrical Code) and local codes.
15. Use the manual override to begin rolling the canopy onto the roller tube, the material must roll over the top
of the roller tube. Ensure the fabric rolls evenlyonto the roller tube.
16. Restore power to the awning.
17. Extend and retract the awning.
18. It will be necessary to adjust the motor limits. Refer to page 3.
19. Install the top cover.
20. Reposition the adjacent awning if it has been moved. Ensure that all the retaining bolts are properly
tightened to 10 ft-lbs.
21. After replacing the motor, it is recommended that a calibration routine is run on the affected awning
because of possible variations in motor performance. Refer to page 4.

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 13
MODIFYING THE TOP COVER
When replacing an older configuration motor with
the current motor, it is necessary to modify the top
cover access holes for the limit switches.
1. Remove and save the two (3) small plugs from
the top of the cover.
2. Measure and mark the new hole locations.
3. Drill two (2) 3/8” holes through the cover in the
locations marked.
4. Clean and deburr the holes.
5. Insert the two plugs removed previously into the
previous holes.
6. Insert the new plugs into the new holes. The
plugs will overlap.
7. Open the top cover and continue with the motor
replacement. Clean any shavings that may have
fallen into the case.
3/4"
Ø 3/8" Hole (x2)
Seam Edge
Extrusion Edge
LH Motor
Seam Edge
Extrusion Edge
RH Motor
2 1/2"
3 13/16"
3/4"
Ø 3/8" Hole (x2)
2 1/2"
3 13/16"
Paramount038

PARAMOUNT Service Manual Carefree of Colorado
14 052548-301r13
SHORT SPRING ARM REPLACEMENT
CAUTION The spring arm is under tension to open. Use extreme care to firmly hold the
spring arms during assembly and disassembly to avoid any sudden or unexpected movement by
the arm. Serious personal injury and/or property damage could occur.
IMPORTANT NOTE: The outer short arms are provided as a set. For correct awning operation, both
the outer arms must be replaced at the same time.
NOTE: Two styles of case knuckles are used on the Paramount short
arms. Early units use the 1-piece knuckle. Later models use the
knuckle with positioning pins. Replacement arms use the knuckle with
positioning pins.
Removing the Existing Arm
1. Extend the awning out to the Slide-Out Cover position.
2. Disconnect power to the awning.
3. For arms with the sensor cable mounted,
carefully remove the sensor cable from the wire
channel on top of the arm. Use care to not
bend, break or compromise the cable.
4. (Refer to Detail A) Remove the 1/2-13 bolt and
washers from the frame mount. Save the screw
and washers.
5. For knuckles with pins: Remove the knuckle plate
and screws. If installed, remove the positioning
pins. It may be necessary to gently lift and pull the
arm to slide the pins out of the housing.
6. While firmly holding the arm, pull the arm
knuckle out of the housing.
7. Fold the arm together and securely tie the arm
closed. Use a 3/8" x 12" plastic tie or
equivalent.
8. Rotate the arm so that it is parallel with the middle
rail to provide access to the setscrew in the arm
knuckle.
9. (Refer to Detail B) Loosen the setscrew then
remove rotation pin from the arm knuckle. Save
the pin.
10. Remove the arm from the awning.
11. On a work surface, rotate the knuckle to provide access to the setscrew located in the knuckle.
12. (Refer to Detail C) Loosen the setscrew and remove the rotation pin from the arm knuckle. Save the knuckle,
screw and pin.
1-Piece Knuckle Knuckle w/
Positioning Pins
paramount18b
B
A
DETAIL A
DETAIL B
Middle Rail
Rotation Pin
#8-32 Set Screw
Arm
Paramount018d
Positioning Pins
Knuckle Plate
1/2” Bolt
& Washers
Knuckle
Housing
Arm
Knuckle
Rotation Pin
#8-32 Set Screw
DETAIL C

Carefree of Colorado Service Manual PARAMOUNT
052548-301r13 15
Installing the New Arm
The new arm is banded in the closed position. Do not remove the binding until instructed to do so.
1. (Refer to Detail C) Attach the knuckle on the new arm using the rotation pin removed previously.
Ensure that the groove in the pin aligns with the setscrew before tightening.
2. (Refer to Detail B) Attach the arm to the middle rail joint using the rotation pin and setscrew removed
previously. Ensure that the groove in the pin aligns with the setscrew.
3. Firmly hold the arm together and remove the binding. Allow the arm to open slowly.
CAUTION When the arm is closed, it can open with significant force. Use care when
opening the arm.
4. (Refer to Detail A) Slide the arm knuckle into the frame mount.
5. For models with the 1-piece knuckle:
Slide the knuckle into the housing. Attach the knuckle to the mount using the 1/2-13 bolt, washer
and lock washer removed previously.
6. For models with positioning pins:
Liberally coat the positioning pins with quality silicone grease.
For awnings under 19' long, two (2) pins are used for the inner and outer
arms in the positions shown. For awnings 19' and longer, the inner
arms use the two pins, the outer arms use one (1) pin in the position
shown.
Slide the positioning pins into the housing with the knuckle. It may be
necessary to gently lift the arm up or down to slide the pins into the
housing with the knuckle.
Attach the knuckle plate to the housing using the screws removed
previously.
Attach the knuckle to the mount using the 1/2-13 bolt, washer and lock washer removed previously.
NOTE: All replacement arms have a wire channel groove in the top of the extrusion. The wire is routed in the
groove and retained using a cord retainer that is wrapped around the wire and pressed into the groove.
7. Route the sensor cable on the replacement arm:
Place a 3" piece of cord retainer onto the cable and press into the groove on top of the arm. Ensure
that the open side of the retainer is facing in toward the channel. Repeat at each end and in the
center of the channel.
At the arm joints, arch the cable slightly to avoid binding. Do not twist the cable.
Paramount018c
Pin Position
(2 per knuckle)
Pin Position
(1 per knuckle)
For All Inner Arms &
Outer Arms In Units under 19’
For Outer Arms In Units over 19’

PARAMOUNT Service Manual Carefree of Colorado
16 052548-301r13
NOTICE Never attempt to adjust or alter the middle rail and attached components. Never
attempt to move or adjust the arm knuckles in the case or on the middle rail; these have been pre-
set at the factory for optimum operation.
LONG SPRING ARM REPLACEMENT
CAUTION The spring arm is under tension to open. Use extreme care to firmly hold the
spring arms during assembly and disassembly to avoid any sudden or unexpected movement by
the arm. Serious personal injury and/or property damage could occur.
Removing the Existing Arm
NOTE: Use a scaffold, ladder or other means to
firmly support the lead rail while removing the arm
and installing the replacement.
1. Extend the awning out fully.
2. Disconnect power to the awning.
3. For arms with the sensor cable mounted,
carefully remove the sensor cable from the wire
channel on top of the arm. Use care to not bend,
break or compromise the cable.
4. (Refer to Detail A) Firmly hold the arm while
removing the set screw and rotation pin from the
middle rail knuckle.
5. Fold the arm together and securely tie the arm
closed. Use a 3/8" x 12" plastic tie or equivalent.
6. Rotate the arm so that it is parallel with the lead
rail to provide access to the set screw located in
the arm knuckle.
7. (Refer to Detail B) Remove the set screw and
rotation pin from the arm knuckle. Remove the
arm from the awning and set aside.
Installing the New Arm
The new arm is banded in the closed position. Do not remove the binding until instructed to do so.
1. (Refer to Detail B) Attach the new arm to the lead rail connector using the rotation pin and set screw
removed previously. Ensure that the groove in the pin aligns with the setscrew.
2. Firmly hold the arm together and remove the binding. Allow the arm to open slowly.
3. (Refer to Detail A) Attach the arm to the middle rail knuckle using the rotation pin and set screw
removed previously. Ensure that the groove in the pin aligns with the set screw.
NOTE: All replacement arms have a wire channel groove in the top of the extrusion. The wire is routed in the
groove and retained using a cord retainer that is wrapped around the wire and pressed into the groove.
4. Route the sensor cable on the replacement arm:
4.1. Place a cord retainer onto the cable and press into the groove on top of the arm. Ensure that the
open side of the retainer is facing in toward the channel. Repeat at each end and in the center of
the channel.
4.2. At the arm joints, arch the cable slightly to avoid binding. Do not twist the cable.
B
A
DETAIL A
DETAIL B
Middle Rail
#8-32 Set Screw
Arm
Rotation Pin
Arm
#8-32 Set Screw
Rotatation Pin
Lead Rail
Motion Sensor (ref)
Paramount019

Carefree of Colorado Service Manual P ARAMOUNT
052548-301r13 17
REMOVING THE AWNING
CAUTION The Paramount awning is extremely heavy. Moving and/or lifting
the awning requires a minimum of 3 people. The use of a lifting device is strongly
recommended.
1. Retract the awning completely.
2. Disconnect power to the awning.
3. Locate the junction box where the motor wires are routed. Disconnect the motor wires and remove
from the junction box. Make note of the wire colors. Bundle the wire to the awning.
NOTE: Some installations use a waterproof junction box located on the top of the coach, others
may have the junction box located inside the coach at or near the cable entry point.
4. Disconnect the sensor cable.
For installations with a junction box: Some installs may route the cable into a junction box with a cable
coupler. Disconnect the cable from the awning and remove from the junction box. Bundle the cable to
the awning.
For installations hardwired to the control box (option 1). Trace the cable to the control box. Disconnect
the cable from the control box and remove from the coach. Bundle the cable to the awning.
For installations hardwired to the control box (option 2). If it is not possible to disconnect the cable from
the control box and remove from the coach, locate the cable inside the coach and at a convenient point,
cut the cable. Pull the cable out and bundle to the awning. If using this method, it will be necessary to
order a cable coupler and two phone cable connectors when reinstalling the awning.
5. The awning is mounted using 4 mounting
brackets attached to the roof of the coach.
Each mounting bracket has a retaining bolt in
the back side to hold the awning into the
bracket. Loosen all 4 of the retaining bolts. It
is not necessary to remove the bolts from the
brackets.
6. Slide the awning back and up to remove the
awning from the brackets.
7. To reinstall the awning, reverse the procedure above.
Special Notes:
a) When attaching the motor wires ensure that the wire colors match the previous configuration. All
wiring must conform to NEC (National Electrical Code) and local codes.
b) If the sensor cable was cut to remove the awning, it is necessary to install a connector on each cut
end of the cable. The connector must be attached as shown in the wiring diagrams. A coupler is
then used to attach the two connectors.
8. After installing the awning, test the operation (refer to page 19). It may be necessary to adjust the lead
rail height (refer to page 6).
Paramount020
Profile
5/16-18 x 1 1/2
Retaining Bolt & Square Nut
(1 per bracket)
Mounting Bracket
(ref)

P ARAMOUNT Service Manual Carefree of Colorado
18 052548-301r13
DIAGNOSTIC TESTS
The following procedures are intended to aid the service technician to logically resolve operational issues with the
Direct Response installation.
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
Refer to the appropriate wiring diagram:
Wiring Diagram – Single Awning page 23
Wiring Diagram – 2 - Awnings page 23
Wiring Diagram – 4 - Awnings page 26
Procedures in this section: Page
COMMON OPERATIONAL ITEMS.......................................................................................................................18
TESTING THE SYSTEM.....................................................................................................................................19
D01 -THE AWNING(S)OPERATE DIFFERENT THAN THE SWITCH MARKINGS........................................................20
D02 -THE AWNINGS DO NOT OPERATE (ALL).................................................................................................20
D03 -ONE AWNING DOES NOT OPERATE .......................................................................................................21
D04 -AWNING(S)DO NOT RETRACT DURING WINDY CONDITIONS...................................................................22
D05 –AWNING(S)DO NOT MOVE WHEN REMOTE CONTROL BUTTONS ARE PUSHED.......................................22
C OMMON O PERATION I TEMS
The following items are operational items that may come up as questions during normal operation. These are
also given in the operator's manual.
1. Each awning has an independent motion sensor. During windy conditions, the awnings may not retract
concurrently.
2. The auto-retract system functions in two stages. The first stage is when the awning is extended past the slide-
out position. The awning will retract and stop at the slide-out cover position to provide continued protection for
the slide-out room.
When in the slide-out cover position, the awning is very robust. The auto-retract system is active but uses a
higher factory preset threshold value for extreme weather conditions. When the motion of the awning exceeds
the extreme weather threshold, the awning will close to the full retract position. The second stage sensitivity
(threshold) value is not controlled by the keypad settings.
3. If an optional EL ignition lockout is installed, the system will disable the extend function while the vehicle
ignition key is in the ON position. If the RTL ignition lockout with retract is installed, the awning will retract to
the closed position and disable the extend function. Operation will return to normal when the key is OFF.
4. If the AC power source is disrupted while the awning is moving, the awning will stop. When power is
restored, extend and retract functions will operate normally. Pressing an intermediate stop (slide-out
and window) the awning will first retract then go to the selected position.
5. The awning motor is equipped with a thermal protection circuit to protect the motor from overheating.
Operating the awning repeatedly over a short time period may cause the circuit to sense a overheat condition
and shut off the motor. If this occurs, wait approximately 15 minutes to allow the motor to cool then operate
the awning in normal fashion.