Carlisle BINKS DEVILBISS HAR-600 User manual

SB-6-147-R2 (1/2021) 1 / 4 www.carlisleft.com
Risk of personal injury.
Risk of property damage.
Except as otherwise specified by the manufacturer, this product
is specifically designed for compressed air service and use
with any other fluid (liquid or gas) is a misapplication. For
example, use with or injection of certain hazardous gases in
the system (such as oxygen or liquid pertroleum gas) could
be harmful to the unit or result in a combustible condition
that may cause fire or explosion. Manufacturer’s warranties
are void in the event of misapplication and manufacturer as-
sumes no responsibility for any resulting loss.
Risk of injury. Release all air pressure from system before
servicing system. Be sure to read and understand all Service
Bulletins on the separate components before using the system.
Use only specified DeVilbiss parts.
IMPORTANT:
Read and follow all instructions and SAFETY PRECAUTIONS before
using this equipment. Retain for future reference.
DESCRIPTION
This regulator has been designed to receive air at main line pressure
and to deliver it at a desired lower regulated pressure.
Specifications
Air inlet 3/8" NPT(F)
Air outlets 1/4" NPT(F) (3 Ea.)
Air Capacity 60 CFM
Maximum Temp. 150° F
Max. Inlet Pressure 250 psi
Regulator range 0-125 psi
INSTALLATION
1. Maximum inlet pressure and operating temperature ratings are
250 psig and 150° F (intermittent to 180° F).
2. Install as close as possible to where regulated air is needed.
3. Install the unit with the air flowing through the body in the direc-
tion indicated by the arrow.
4. Install the same pipe size unit as the pipe line in use. Avoid using
fittings, couplings, etc., that restrict the air flow, unless maximum
flow is not needed.
5. Regulator may be installed so that adjusting handle is in any
position. Attach gauge to one 1/4" female port.
6. Turning the adjusting screw clockwise increases the regulated
pressure and turning it counterclockwise reduces the regulated
pressure.
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and understand this manual.
Contact your local Carlisle Fluid Technologies representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT.
EN
SERVICE MANUAL
HAR-600 AIR REGULATOR AND GAUGE
HAR-507 AIR REGULATOR

EN
SB-6-147-R2 (1/2021)2 / 4www.carlisleft.com
Ind.
Ref Replacement Parts
No. Part No. Description Req.
1 HAR-507 Regulator 1
2 GA-288 Gauge 1
3 — 1/4" NPT Street Elbow 1
4 VA-542 Ball Valve 1
5 — 1.4" NPT Plug 1
PARTS LIST – Model HAR-600 Regulator and Gauge Assembly
INSTALLATION
Assemble gauge (2), elbow (3), ball valve (4) and plug (5) to
regulator as shown. Use quality pipe sealant or PTFE tape
(not supplied) when installing above components and when
installing regulator to air line piping.
Air Inlet
3/8" NPT
5
4
3
1/4" NPT
Outlet
1/4" NPT
Outlet
2
1
Ind.
Ref Replace. Parts
No. Part No. Description Req.
1 — #10-32x9/16 Fillister Hd. Screw 6
2 — Cover 1
3 — Spring Button 1
4 — Diaphragm Spring 1
5 — Body 1
6 — Pipe Plug 1/4" NPT(M) 1
7 KK-4977 Repair Kit (includes # 8 thru 13) 1
8 — Diaphragm Assy. 1
9 — O-Ring 1
10 — Valve 1
11 — O-Ring 1
12 — Spring 1
13 — O-Ring 1
14 — Bottom Plug 1
PARTS LIST – Model HAR-507 Regulator Assembly
A
1
2
3
4
5
8
697
10
11
12
13
14
REGULATOR MAINTENANCE
1. Occasionally remove bottom plug (7) and clean valve
seat (11) and body. Clean parts with denatured alcohol,
wipe off seat and blow out body with compressed air.
2. To disassemble regulator, remove screws, bonnet,
spring and spring button. Diaphragm assembly can
now be removed.
3. Check all O-rings for signs of damage. Replace if
necessary.
4. Reassembly of parts. Insert stem of valve through
hole in regulator body. Install spring and o-rings.
Screw bottom plug into body.
Note
Erratic operation or loss of regulation is usually due
to dirt in the valve area and cleaning is necessary.
If cleaning does not correct the problem, replace
the items included in Repair Kit KK-4977. If unit leaks
air at A, install Repair Kit KK-4977.

EN
SB-6-147-R2 (1/2021) 3 / 4 www.carlisleft.com
NOTES

EN
SB-6-147-R2 (1/2021)4 / 4www.carlisleft.com
WARRANTY POLICY
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,
will void all warranties. Failure to reasonably follow any maintenance guidance provided
may invalidate any warranty.
For specic warranty information please contact Carlisle Fluid Technologies.
Carlisle Fluid Technologies is a global leader in innovative nishing technologies.
Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.
BGK™, Binks®, DeVilbiss®, Hosco®, MS®, and Ransburg®
are all registered trademarks of Carlisle Fluid Technologies, Inc.
©2021 Carlisle Fluid Technologies, Inc.
All rights reserved.
For technical assistance or to locate an authorized distributor,
contact one of our international sales and customer support locations.
Region Industrial/Automotive Automotive Renishing
Americas Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]
Europe, Africa,
Middle East, India
Tel: [phone]
Fax: [phone]
China Tel: [phone]
Fax: [phone]
Japan Tel: [phone]
Fax: [phone]
Australia Tel: [phone]
Fax: [phone]
For the latest information about our products, visit www.carlisleft.com