Casablanca 42900-01W User manual

www.CasablancaFanCo.com 1.888.227.2178
PAGE
11
PAGE
15
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation
Ladder
PAGE
3
Tools Needed
Operation Maintenance
& Cleaning TroubleshootingLight Kit
PAGE
5
Hanging the Fan
?
?
?
PAGE
12
PAGE
14
Table of Contents
PAGE
4
Ceiling Plate
Congratulations on purchasing your new Casablanca®
ceiling fan! It will provide comfort and performance
in your home or ofce for many years. This installation
and operation manual contains complete instructions
for installing and operating your fan.
We are proud of our work and appreciate the
opportunity to supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.CasablancaFanCo.com/register
Save your receipt for proof of purchase.
PAGE
6
Wiring Canopy
PAGE
8
PAGE
7
Wall Control
PAGE
10
Blades
1
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company

www.CasablancaFanCo.com 1.888.227.2178
www.CasablancaFanCo.com 1.888.227.2178
www.CasablancaFanCo.com 1.888.227.2178
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip to
nearest wall or
obstruction 7 feet
from bottom
edge of blade
to the oor
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Casablanca Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Casablanca replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
Must be able to
secure the fan to
building structure or
fan-rated outlet box
2
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
2

www.CasablancaFanCo.com 1.888.227.2178
3
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
Tools Needed
Power Drill
(optional)
9/64” Drill
Bit (optional)
Ladder Wire Strippers
If mounting to a support structure, you will also need these tools.
Screwdriver
(included)

www.CasablancaFanCo.com 1.888.227.21781.888.227.2178 www.CasablancaFanCo.com
Ceiling Plate
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
OFF
Turn Power
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling plate
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70
lbs) or less.
Make sure all four bumpers are
still attached.
Bumper
4
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company

www.CasablancaFanCo.com 1.888.227.2178
5
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
DO NOT PICK THE FAN UP BY THE
WIRES. Use the hanging hole on the
body of the fan to hang the fan on the
hook of the ceiling mounting plate.
Unlock the canopy cover from the canopy
ring tabs to loosen the canopy ring and
lower it down to the fan body as shown.
Hanging the Fan

www.CasablancaFanCo.com 1.888.227.2178
6
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
Wiring
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
Using an orange wire connector
from the hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
P
L
A
T
E
green/yellow stripe (grounding)
green
green
F
R
O
M
F
A
N
Using an orange wire connector:
• Connect the black (ungrounded)
wire from the ceiling to the black
wire from the fan/receiver.
• Connect the white (grounded)
wire from the ceiling to the white
wire from the fan/receiver.
F
R
O
M
F
A
N
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded) white (grounded)
black white

www.CasablancaFanCo.com 1.888.227.2178
7
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
1. Using a 9/64 drill bit, drill a hole
in each screw cut-out on the wall
control template.
2. Using a hammer, tap a drywall
anchor found in the wall control
hardware bag into each hole
until the drywall anchor is ush
with the wall.
1. Using a drywall punch saw,
cut out the interior shape of
the template using one of
the four drilled corners as a
starting point.
2. Remove the template and the
cut-out section of drywall.
1. Insert the wall control into the
dry wall cut out.
2. Align the screw holes in the wall
control with the drywall anchors.
3. Install the cover plate using
a Phillips Head screwdriver
to secure the two cover plate
screws found in the wall control
hardware bag through the wall
control and into the drywall
anchors.
Wall Control
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
If you are using a outlet box for wall control installation, the wires coming from the wall
control must be grounded using the attached green wire. If not placed in an outlet box, cap
the green wire coming from the wall control with an included wire nut.
1. Tape the provided wall control
template with painter’s tape at
the desired installation area.
2. Drill holes inside the four
corners of the template.
Note: Make sure the wall
control template is level before
proceeding to the next step.
Template
Drywall
Before
After
Cover Plate
Template
Drill Holes
Painter’s
Tape Template
Drywall
Anchors
Screw
Cut-Out

www.CasablancaFanCo.com 1.888.227.2178
Canopy
Partially install two of the canopy screws,
found in the hardware bag, into screw
holes on opposite corners of the ceiling
plate as shown. Choose the two screw holes
that are aligned with the hanging slots in
the fan body.
Using both hands, lift the fan body from the
hook and align the hanging slots on both sides
of the fan body with the two partially installed
canopy screws. Slide the two slots on both
sides of the fan body between the head of the
screws and rotate the fan body clockwise so the
screws hold the fan body rmly in place.
Install the remaining two canopy screws,
found in the hardware bag, by holding
the fan body cover to the ceiling mounting
plate. Tighten all four screws securely.
Hanging Slot
Canopy Screw
8
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company

www.CasablancaFanCo.com 1.888.227.2178
9
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
Canopy (continued)
To install the canopy ring, lift the
canopy, then rotate clockwise until
the tabs are held in place by the
tab holders, locking the canopy
ring into place.
To check your work, make sure
there is an even gap all the way
around between the ceiling and
the canopy ring.
Before going to the next step, locate
the two sets of canopy ring tabs that
are on the top edge of the canopy
and the two sets of canopy tab
holders found at the top of the fan
body near the ceiling.
Canopy
Ring
Tabs
Canopy
Tab
Holders

www.CasablancaFanCo.com 1.888.227.2178
42900-01 • 03/18/15 • © 2015 Casablanca Fan Company
Install the blade using three blade screws
and washers, found in the hardware bag.
Repeat this process for all ve blades.
Blades
10
Slide a blade into a slot located on the blade ring.
Note: The blades will only t properly over the
screws holes one way. If the holes do not line up,
remove the blade and turn it over.