Casablanca 99050 User manual

Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca fans
Models 99050, 99051,99052, 99053, 99054, 99055
M8505-01 • 11/21/12
Decorative Low Prole
Integrated Kit
Decorative Low Prole
Integrated Kit
Installation Manual

M8505-01 • 11/21/12 M8505-01 • 11/21/12
1.888.830.1326 1.888.830.1326
2 3
If your fan’s switch housing cap resembles
this one, remove the switch housing
screws using a Phillips head screwdriver.
Then remove the plug button using a
standard screwdriver. Then follow the
TYPE-B ASSEMBLY INSTRUCTIONS on
pages 6-7.
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
assembly screws with a Phillips head
screwdriver.Remove the plug button.
Then follow the TYPE-C ASSEMBLY
INSTRUCTIONS on pages 8-9.
If your fan’s switch housing cap resembles
this one, remove the cap screws with a
Phillips head screwdriver. Then follow the
TYPE-A ASSEMBLY INSTRUCTIONS on
pages 4-5.
Switch
Housing
Cap
Cap
Screw
WHICH ASSEMBLY METHOD WILL I USE?
Switch
Housing
Cap
Switch
Housing
Screw
Switch
Housing
Screw
Switch
Housing
Screw
Plug
Button Plug
Button
Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s
switch housing. Begin on page 3 where you will choose the type of switch housing that
most closely resembles the one on your fan. From there, you will be directed to the set of
assembly instructions that are appropriate for installing the light kit to your fan.
Read entire installation instructions carefully before
beginning installation and save these instructions.
BEFORE YOU BEGIN
Switch
Housing
Choose one of the four images below that most closely resembles the switch
housing on your fan; then follow the instructions under the image.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of re, electrical shock, or personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the
mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by
turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the
service panel.
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are
unfamiliar with wiring, use a qualied electrician.
CAUTIONS
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the two cap screws from the
inside of the switch housing. Reinstall
the switch housing. Tighten the switch
housing screws.Then follow the TYPE-A
ASSEMBLY INSTRUCTIONS on pages 4-5.

M8505-01 • 11/21/12 M8505-01 • 11/21/12
1.888.830.1326 1.888.830.1326
4 5
TYPE-A ASSEMBLY INSTRUCTIONS
Partially install the two mounting screws
into the bottom of the lower switch housing.
Mounting
Screw
Wire
Connector
Switch
Housing
Lift the light kit up to meet the
lower switch housing. Wrap keyhole
slots around the screws and twist
counterclockwise. Tighten screws.
Keyhole
Slots
Mounting
Screw
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)
1
3
2
4
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Do not allow the light kit to hang
only by the wire connections!”
After the light kit is mounted to the fan, feed
the pull chains from the fan’s switch housing
and the light kit through the grommeted
holes in the base of the light kit. Extension
chains are provided, if necessary. Both pull
chains must line up with the grommeted
holes to operate properly.
Grommeted
Hole
Pull Chain
Indentation
Tab
Installing the bulb - Install a bulb into each
of the sockets. When necessary, replace
with bulbs of the same type and wattage.
Socket
Installing the Pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit. Turn
power on. Your installation is complete.
5
7
6
8
Installing the globe (sold separately)- Position the
indentations in the outer rim of the globe so that they
line up with the tabs on the inside surface of the light
xture rim. Carefully lift the globe up inside the light
xture as far as it will go. Rotate the globe in a clockwise
direction until it is held tightly in place by the four tabs.

M8505-01 • 11/21/12 M8505-01 • 11/21/12
1.888.830.1326 1.888.830.1326
6 7
After the light kit is mounted to the fan, feed
the pull chains from the fan’s switch housing
and the light kit through the grommeted
holes in the base of the light kit. Extension
chains are provided, if necessary. Both pull
chains must line up with the grommeted
holes to operate properly.
Grommeted
Hole
Pull Chain
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
TYPE-B ASSEMBLY INSTRUCTIONS TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)
Lift the light kit assembly up so that the
screw holes in the lower switch housing
line up with the holes in the upper switch
housing. Install the switch housing
screws and tighten securely.
Feed the wires through the center hole in
the switch housing, the washer, and the nut.
Then install the switch housing by twisting
clockwise onto the threaded rod. Install
the washer and nut onto threaded rod and
tighten securely.
1 2
4
Wire
Connector
Switch
Housing
Switch
Housing
Screw
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Indentation
Tab
Installing the bulb - Install a bulb into each
of the sockets. When necessary, replace
with bulbs of the same type and wattage.
Socket
Installing the Pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit. Turn
power on. Your installation is complete.
5
7
6
8
Do not allow the light kit to hang
only by the wire connections!”
3
Installing the globe (sold separately)- Position the
indentations in the outer rim of the globe so that they
line up with the tabs on the inside surface of the light
xture rim. Carefully lift the globe up inside the light
xture as far as it will go. Rotate the globe in a clockwise
direction until it is held tightly in place by the four tabs.

M8505-01 • 11/21/12 M8505-01 • 11/21/12
1.888.830.1326 1.888.830.1326
8 9
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)TYPE-C ASSEMBLY INSTRUCTIONS
Feed the wires through the center hole in
the switch housing. Then using the single
pin connectors, connect the black or blue
wire from the fan to the black wire from
the light kit. Connect the white wire from
the fan to the white wire from the light kit.
Lift the lower switch housing up so
that the screw holes line up with the
holes in the upper switch housing.
Install the switch housing screws and
tighten securely.
Lift the light kit up, tucking the wires into
the hole in the switch housing. Install the
center stem of the light kit into the lower
switch housing by turning the threaded
rod clockwise into the threaded hole.
Continue turning until tight.
Upper
Switch
Housing
1
3
2
4
Threaded
Rod
Lower
Switch
Housing
Switch
Housing
Screw
Wire
Connector
Switch
Housing
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Do not allow the light kit to hang
only by the wire connections!”
After the light kit is mounted to the
fan, feed the pull chains from the fan’s
switch housing and the light kit through
the grommeted holes in the base of the
light kit. Extension chains are provided,
if necessary. Both pull chains must
line up with the grommeted holes to
operate properly.
Grommeted
Hole
Pull Chain
Indentation
Tab
Installing the bulb - Install a bulb into each
of the sockets. When necessary, replace
with bulbs of the same type and wattage.
Socket
Installing the Pull chain pendant -
Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit. Turn
power on. Your installation is complete.
5
7
6
8
Installing the globe (sold separately)- Position the
indentations in the outer rim of the globe so that they
line up with the tabs on the inside surface of the light
xture rim. Carefully lift the globe up inside the light
xture as far as it will go. Rotate the globe in a clockwise
direction until it is held tightly in place by the four tabs.

M8505-01 • 11/21/12
1.888.830.1326
10
ONE YEAR WARRANTY
This product is warranted to the original purchaser by Casablanca Fan Company/
Hunter Fan Company against defects in material and workmanship for one (1)
year from date of purchase. During the warranty period, we will repair or, at our
option, replace a defective product at no charge. For information on how to obtain
service, contact the Casablanca/Hunter Service Department by calling our toll-
free number at 888-830-1326. Damage to the product caused by mishandling,
improper installation or modication is not covered by this warranty. This warranty
is given in lieu of all other warranties expressed or implied. Some states do not allow
limitations of time on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specic legal rights which may vary from
state to state.
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power
wires are correctly connected to the ceiling and the light kit.
If you have problems installing or operating your light kit, do not return this product
to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
Monday through Friday
8:00 am to 4:30 pm Central