Casall EB100 User manual

1
Casall EB100
Bike
91030

2
Important: Please locate your serial number and record in the box below for service
support purposes.
Serial number here:

Serial number

3
EB100

4
Assembly Diagram

5
EXPLODED DIAGRAM

6
PARTS LIST
PARTS NO. DESCRIPTION Q'TY
A,A-2 Console & screw 1SET
B-1 Handlebar 1PCS
B-2 Foam Grip 2PCS
B-3 Hand pulse 2PCS
B-4 Cap for handlebar 2PCS
B-5 Pulse wire 1PCS
B-6 Screws M4x20L 2PCS
C-1 Left cover for hand post 1PCS
C-2 Screws M5xP0.8x20L 2PCS
C-3 Tension knob w/cable 1PCS
C-4 Semicircle washer φ8xφ19x2t 2PCS
C-5 Flat washers φ8*φ19*2T 2PCS
C-6 Allen bolt M8*P1.25*16L 4PCS
C-7 Hand post 1PCS
C-8 Right cover for hand post 1PCS
C-9 Sensor wire 1PCS
D-1 Seat slider 1PCS
D-2 Bolt for seat slider 1PCS
D-3 Cap for seat slider 2PCS
D-4 Flat washer φ14.3xφ25x2.0t 1PCS
D-5 Knob for seat slider 1PCS
D-6 Seat post 1PCS
E-1 Down tension cable 1PCS
E-2 Screw M4x10L 1PCS
E-3 Sensor box 1PCS
E-4 Sensor holder 1PCS
E-5 Main frame 1PCS
E-6 Bearing 2PCS
E-7 Wav washer φ17.5xφ25x0.3t 1PCS
E-8 Flat washer φ17.5xφ25x0.3t 1PCS
E-9 C-Type φ17 1PCS
E-10 Adjust knob for seat post 1PCS

7
E-11 Plastic bushing 1PCS
E-12 Left crank 1PCS
E-13 Right crank 1PCS
E-14 Nylon screws M8xP1.0x20L 2PCS
E-15 Screws M4x50L 6PCS
E-16 Left chain cover 1PCS
E-17 Screws M5x16 6PCS
E-18 Right chain cover 1PCS
E-19 Front cover (Left) 1PCS
E-20 Front cover (Right) 1PCS
E-21 Seat 1PCS
E-22 Pedal 1SET
E-23 Cover for hand post 1PCS
F-1 Hex. screws M8xP1.25x12Lx5t 3PCS
F-2 Shaft 1PCS
F-3 Pulley wheel 1PCS
F-4 Bushing 1PCS
F-5 Belt 1PCS
G-1~G4 Magnet system 1SET
H-1~H-12 Flywheel set 1SET
I-1 Left cap for front stabilizer 1PCS
I-2 Front stabilizer 1PCS
I-3 Allen bolt M8xP1.25x40L 2PCS
I-4 Transport wheel for front stabilize 2PCS
I-5 Nuts M8 2PCS
I-6 Flat washer φ8xφ16x1t 2PCS
I-7 Right cap for front stabilizer 1PCS
I-8 Screw 3/16" 4PCS
J-1 Screw 3/16" 4PCS
J-2 Left cap for rear stabilizer 1PCS
J-3 Pad for rear stabilizer 2PCS
J-4 Rear stabilizer 1PCS
J-5 Right cap for rear stabilizer 1PCS
L-1~L-12 Bolts & nuts pack 1SET
Q-1~Q-9 Idler wheel set 1SET

8
Step 1
1. Attach the Front Stabilizer (I-2) to the Main Frame (E-5) using two M8xP1.25x20L Allen bolt
(L-9) and Flat washers (L-8).
2. Attach the Rear Stabilizer (J-4) to the Main Frame (E-5) using two M8xP1.25x20L Allen bolt
(L-9) and Flat washers (L-8).
Step2
1. Assemble the straps onto the pedals as the sketches. Adjust the ideal length of the straps
according to your foot size.
2. Assemble the two Pedals (E-22L/R) onto the Crank (E-12L/R) with a screw driver.
Remarks: Screw the left pedal’s spindle counter-clockwise and the right pedal’s spindle
clockwise. Use a wrench (or screwdriver) to screw the two spindles completely.
3. Assemble the seat (E-21) to the Slider. The Slider can be adjusted in different angles. Tighten
the two Nuts under the Seat using a screwdriver. In addition, the Slider can be adjusted in
horizontal level by loosening the Knob.
4. Insert the seat post (D-6) into the main frame, then choose the desired position and tighten the
knob. Be sure the knob (E-10) is always securely fastened.
Remarks: When you have chosen a desired position, tighten the Seat Post Knob until you
hear a “click”.

9
Step 3
1. Please remove the M8*P1.25*16L Allen bolt (C-6) and semicircle washers (C-4) and flat
washers (C-5) from the main frame.
2. Pull the upper tension control (C-3) of the handlebar post (C-7) and ensure the tension knob is
at the lightest position (minimum position).
3. Connect the upper tension control (C-3) and down tension cable (E-1), then connect the upper
sensor wire (C-9) and down sensor wire (E-3).
4. Slide the Handlebar post (C-7) into the Main frame (E-5) then fix it with four sets of
M8*P1.25*16L Allen bolt (C-6) and semicircle washers (C-4) and flat washers (C-5).
Remarks: Do not screw one set of the M8*P1.25*16L Allen bolt and semicircle washers too
firm at one time. It is better to fix the four sets firmly at the same time because it helps you
to change angles and to fix more easily.

10
Step 4
1. Pass the hand-pulse wire (B-5) through the hole.
.
2. Attach the handlebar (B-1) to the handlebar post (C-7) using the metal clamp (L-2). Fix firmly
with one flat washer (L-4), one Spring washer (L-5) and one Fixing bolt (L-6).
3. Tighten all parts together with T-Knob (L-7), spring washer (L-5), flat washer (L-4). Please
ensure it is secured very well.

11
Step 5
1. The console (A) can use two AA batteries (not 11 included); alkaline batteries are
recommended.
Do not use old and new batteries together or alkaline, standard, and rechargeable batteries
together. IMPORTANT: If the console has been exposed to cold temperatures, allow
it to warm to room temperature before you insert batteries. Otherwise, you may damage
the console displays or other electronic components.
Remove the battery cover from the back of the console (A), and insert batteries into the battery
2. Please remove the screws (A-1) from the console (A).
3. Connect the upper sensor wire (C-9) and hand pulse wire (B-5) by the console (A) , then
attach the console (A) to the console bracket with the enclosed screws.
4. Pass the R/L cover (C-1 & C-8) through the handlebar (B-1).
3. Remove the pre-installed screws (C-2) on the handlebar post first, Attach the Right and Left
cover (C-1 & C-8) using screws (C-2) and screws (L-1)
Remove the pre-installed screws (C-2) on the handlebar post first.

12
INSTRUCTIONAL MANUAL ST3604-67

13
DISPLAY FUNCTION :
ITEM DESCRIPTION
SCAN
. The sequence of display: TMR→SPD→DST→CAL→PULSE
. In SCAN mode, press MODE key to choose other functions.
. Automatically scan through each mode in sequence every 6 seconds.
SPEED (SPD)
. W/O any signal been transmitted into the monitor for 4 seconds, SPEED
will display “0.0”
. Display current training speed.
TIME (TMR)
. W/O setting the target value, time will count up.
. With setting the target value, time will count down from your target time to
0, and as 0 is achieved time alarm.
. W/O any signal been transmitted into the monitor for 4 seconds, time will
STOP
. Range 0:00 ~ 99:59
DISTANCE (DST)
. W/O setting the target value, distance will count up.
. With setting the target value, distance will count down from your target
distance to 0, and as 0 is achieved distance alarm.
. Range 0.0~999.9 KM
CALORIES (CAL)
. W/O setting the target value, calorie will count up.
. With setting the target value, calories will count down from your target
calorie to 0, and as 0 is achieved calorie alarm.
. Range 0.0~999.9 Cals
.Calorie count on the display only serves as a general guideline. For detail
calorie consumption for each individual please consult a physician or a
nutritionist.
PULSE
. With pulse signal into for 6 seconds, the current pulse will display.
. W/O pulse signal into for 6 seconds, it displays “P”
. Pulse alarm when over preset target pulse.
. Range 0-40~240 BPM

14
BUTTON FUNCTION:
Power on & off：
Power on：
. LCD will display all segments with Bi sound as Drawing A.
Drawing A
Power off：
. Without any signal been transmitted into the monitor for 4 minutes, and the monitor enter to SLEEP.
OPERATION :
1. When monitor power on (or press MODE, RESET key and hold for 3 seconds), LCD will display all segments with Bi
sound for one second and enter to SCAN mode as Drawing B.
2. With any signal been transmitted into the monitor, the value of TMR, DST, and CAL will start to count up as Drawing
C.
3. Without any signal been transmitted into the monitor for 4 minutes, the monitor will enter to SLEEP mode.
ITEM DESCRIPTION
Reset
. In setting condition, press RESET key once to reset the current function figures.
. Press RESET key and hold for 2 seconds to reset all function figures, and have Bi sound for
prompt at the same time.
SET
. Each adding by pressing once, press and hold the button to increase the value faster
. TMR setting range: 0:00~99:00 (Each increment is 1:00)
. CAL setting range: 0.0~999.0 (Each increment is 1.0)
. DST setting range: 0.0~999.0 (Each increment is 1.0) KM
MODE
. Choose each function by pressing MODE key. In SCAN mode, press MODE key can lock the
current function.
. Press MODE key and hold for 2 seconds to reset all function figures.

15
DrawingB DrawingC
Trouble shooting:
. When the display of LCD is weak, it means the batteries need to be changed.
. If there is no signal when you pedal, please check if the cable is well connected.
NOTE :
1. Stop training for 4 minutes, the main screen will be off.
2. If the computer displays abnormally, please re-install the battery and try again.
3. Battery Spec: 1.5V UM-3 or AA (2PCS).