Casall EB600 91003 User manual

Casall EB600
Bike
91003

Exploration drawing

Drawing for assemble
1

PARTS LIST
NO. Description Specifications Q'TY
A,A-1 COMPUTER & SCREW 1PCS
B HANDLEBAR 1PCS
B-1 HAND PULSE SET 1SET
B-2 FOAM GRIP 270Lxφ23x5mm 2PCS
B-3 FOAM GRIP 360xφ23x5.0m 2PCS
B-5 CAP FOR HANDBLEBAR 2PCS
B-6 SCREWS FOR HANDLEBAR M3x20L 2PCS
B-7 PULSE CABLE 700+700mm 1PCS
C HANDLEBAR POST 1PCS
C-1 COMPUTER CABLE (UPPER) 1PCS
C-2 BOTTLE CAGE 1PCS
C-3 SCREW FOR BOTTLE CAGE M5xP0.8x14L 2PCS
D MAIN FRAME 1PCS
D-2 SCREW FOR HAND POST M8*P1.25*16L 4PCS
D-3 CURVED WASHER φ8xφ19x2t 4PCS
D-4 ADJUSTING KNOB FOR MAIN FRAME 1PCS
D-5 BELT 1PCS
D-6 BIG PULLEY 1PCS
D-7 SHAFT 1PCS
D-8 SCREW M8Xp1.25x12Lx5t 3PCS
D-12 BEARING 6203 (RS) 2PCS
D-13 PLASTIC BUSHING 1PCS
D-14 SENSOR BOX 1PCS
D-15 SCREW FOR SENSOR BOX M4x10L 1PCS
D-16 SCREW FOR CHAIN COVER 3/16”(#10)x3/4” 10PCS
D-17 SCREW FOR CHAIN COVER M4x50L 4PCS
D-18 CHAIN COVER (L) 1PCS
D-19 CHAIN COVER ( R) 1PCS
D-20 DISC (R ) 1PCS
D-21 ROUND DISC 2PCS
D-22 NUT FOR DISC M10Xp1.25x10T 2PCS
D-23 CAP FOR ROUND DISC 2PCS
D-24 SCREW FOR DISC M4x14L 8PCS
D-25 FLAT WASHER φ15xφ16x1t 8PCS
D-26 DISC (L) 1PCS
D-27 MAGNET SYSTEM 1SET

D-28 SPRING WASHER φ6 2PCS
D-29 SCREW FOR MAGNET SYSTEM M6xP1.0*16L 2PCS
E~E-11 FLYWHEEL SET 1SET
F-F FRONT STABILIZER 1PCS
F-B REAR STABILIZER 1PCS
G SEAT POST 1PCS
G-1~G-5 SEAT SLIDER 1SET
G-6 SEAT 1PCS
H PEDAL 1SET
I~I-8 IDLER WHEEL.SET 1SET
J METAL COVER 1PCS
J-1 NUT M8 4PCS
J-2 CARRIAGE BOLT M8xP1.25x55L 4PCS
J-3 FLAT WASHER φ8*φ19*2T 4PCS
J-4 BOLT FOR HANDLEBAR M7xP1.0x30L 1PCS
J-5 FLAT WASHER φ7xφ12x1t 2PCS
J-6 SPRING WASHER φ7x2t 2PCS
J-7 BUSHING φ7xφ12x40mmL 1PCS
J-8 T-KNOB 1PCS
J-9 FRONT COVER FOR HANDLEBAR 1PCS
J-10 REAR COVER FOR HANDLEBAR 1PCS
J-11 SCREW FOR COVER M3x14L 2PCS
K ADAPTOR 1PCS

Step 1
Step 2
Step1
Foot Tube Assembly
Attach the Front Stabilizer (pt.F-F)
to the Main Frame (pt.F-F) using
two Domed Nuts (pt.J-1), two Flat
Washers (pt.J-3) and two Carriage
Bolts (pt.J-2) Attach the Rear
Stabilizer (pt.M) to the Main Frame
(pt.F-B) using two M8 Domed
Nuts (pt.J-1), two Flat Washers
(pt.J-3) And two Carriage Bolts
(pt.J-2).
Pedal Assembly
Fix the two pedals (H-R+L) onto the
Disc (D-20 + D-26) by screw
driver.
Remarks: Screw the left pedal’s
spindle anti-clockwise and the right
pedal’s spindle clockwise. Use a
wrench (or screwdriver) to screw the
two spindles completely.
R
L

Step 3 --Seat Tube Assembly
1. Assemble the seat (pt.G-6) to the selector rail, position the rail onto the seat post (pt.G) and
tighten using the butterfly knob .
2. Insert the seat post (pt.G) in the main frame (pt.D), choose the desired position and tighten
the knob. Ensure that the knob is always tightened.
If you cannot insert the seat tube into the reception tube of the mainframe after you have
pulled out the cap, please unscrew the spring knob a little more till the spindle would not hold
the seat tube back.
M16

Step 4-Handlebar post Assembly
1Take the Hand Post (pt.C) and connect the Lower Computer Cable (pt.D-1) and the Upper
Computer Cable (pt. C-1)
2. Slide the Hand Post (pt.C) into the then fix with four sets of M8 Key Head Bolt (pt.D-2) and
Curved Washers (pt.D-3).
4*

Step 5- Handlebar post Assembly
1. Mount the computer (pt .A) to the hold of the handlebar pole with the enclosed screws
(pt .A-2) and connect the computer cables (pt .C-1).
2. Plug the delivered hand-pulse wire for measuring the pulse rate in the socket at the
computer.
3. Assembly the bottle cage (pt.C-2) by screw (pt. C-3).
Step5

Step 6- Handlebar post Assembly
1. Attach the Handlebar (pt.B) to the Front Post (pt.C) using the clamp (pt.J), fix with one
Flat Washers (pt.J-6), one Spring Washers (pt.J-5), one Handlebar Fixing Bolt (pt.J-4)
and then fix the Rear Cover (pt.J-10) . Screw the Handlebar T-Knob (pt.J-8) by one set
of Flat Washer (pt.J-5), Spring Washer (pt.J-6) and one Metal Bush (pt.J-7),
2. Plug the upper cable wire (pt.C-1), and Pulse Sensor Wire (pt.B-7) into the computer cable
box at the back of computer (pt.A), and slide the computer down to the Computer Bracket
situated at the top of the front post (pt.C). Then fix with four Fixing screws M5x12mm
(pt.A-1). Finally, fit the Front Salve (pt.J-9) using two of M5 x 12mm Screws (pt.C-3)
Step6

Monitor manual instruction
【DISPLAY FUNCTION】
TIME : Count up - No preset target, TIME will count up from 00:00 to maximum 99:59 with each increment
is 1 second.
Count down - If training with preset Time, Time will count down from preset to 00:00.Each preset
Increment
or decrement is 1 minute between 1:00 to 99:00.
SPEED : Display current training speed from 0.0 to maximum 99.9 km or ml.
RPM : Display current training rotation per minute.
DISTANCE : Count up - No preset target, Distance will count up from 0.00 to maximum 99.90 with each
Increment 0.1 KM. Count down - If training with preset target, Distance will count down from
preset to 0.00. Each preset increment or decrement is 0.1 KM (or ML) between 0.00 to 99.90.
CALORIES : Count up - No preset target, Calories will count up from 0 to maximum 990 with each 1 cal
increment. Count down - If training with preset target, Calories will count down from preset time
to 0. Each preset increment or decrement is 10 cal from 0 to 990 cal.
PULSE : The monitor can detect pulse signal from handgrip.
HEART SYMBOL: When monitor receive heart rate signal, the symbol will blinking.
WATT : Display current training watt figures.
【FUNCTION BUTTONS:】
MODE: To confirm all settings and to enter into exercise mode.
UP : To select training mode and adjust function value up.
DOWN : To select training mode and adjust function value down.
START/STOP : To start or stop training.
RECOVERY : After exercising for a period of time, keep holding on handgrips and press “RECOVERY” button.
All function display will stop except “TIME” starts counting down from 00:60 to 00:00. Screen will
display your heart rate recovery status with the F1,F2….to F6. F1 is the best, F6. F6 is the worst.
User may keep exercising to improve the heart rate recovery status.
(Press the RECOVERY button again to return the main display.)
(If monitor did not receive heart rate signal, RECOVERY function can not work.)
RESET : Return to main menu in stop mode and clean all preset function value to zero.
TOTAL RESET : To power on the computer.
【OPERATING INSTRUCTION:】
POWER ON
Connect adaptor to the computer to power on, LCD will display all segment with a long- beep as testing for
2 seconds and wheel diameter 78” for seconds (drawing 1).
Drawing 1

【PROGRAMMING MODE】
USER personal data setting (U1 – U4):
1-1 U1 is blinking, user may turn UP and DOWN to select user 1, user 2 to user 4
1-2 Preset personal data (incl. AGE, WEIGHT, HEIGHT, SEX). And press the MODE for
confirmation.
1-3 The computer will enter into MANUAL mode immediately, and selected user may preset
his own exercise data (incl. TIME, DISTANCE, CALORIES and PULSE). The computer will
memorize and will recall those data every time when the user is selected.
1-4 User may start exercise by press START button.
1-5 Press RESET button reverse to training mode selection main menu.
Program selections are MANUAL, PROGRAM, H.R.C., USER, WATT. Press UP and DOWN to
select the program you want and press START for QUICK START in Manual mode.
MANUAL MODE
After selecting MANUAL mode, press UP and DOWN button to increase and decrease level (from 1
to 16) and press MODE button to confirm. Level is adjustable during training. (drawing 2)
Drawing 2
PROGRAM MODE
After enter PROGRAM mode, press UP and DOWN to select program profile from P1 to P12, press
MODE button to confirm and enter the selected profile. User may press UP and DOWN to adjust level.
Level is adjustable during training. (drawing 3)
Drawing 3
H.R.C. MODE
After enter H.R.C. mode, press UP and DOWN to select different target from 55%, 75%, 90% and
TARGET. Press MODE to confirm.

USER MODE
After enter USER mode, the first column of the profile is blinking, user may press UP, DOWN and
then press MODE to create his own profile. (from column 1 to column 20) User may hold on pressing
MODE button for 2 seconds to quit profile setting. (drawing 4). Each user may have his own user
profile.
Drawing 4
WATT MODE
The preset watt value 120 is flashing on screen in WATT setting mode. User may use UP, DOWN
button to set target value from 10 to 350. Press MODE button for confirm.
NOTE:
1. Adaptor spec: 9V, 500MA
2. If computer acted abnormal, user may plug out the adaptor and wait for 5 seconds before plug in
the adaptor again.
3. When computer just power on, it can not be touched or covered by any object or hand within 6
seconds.