Casio CDP-S350 User manual

CDP-S350/EP-S320
MIDI Implementation
CASIO COMPUTER CO., LTD.
Contents
I Overview 3
1 Product Configuration as a MIDI Device 3
1.1 SystemSection.......................................... 3
1.2 Performance Controller Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 SoundGeneratorSection .................................... 3
2 Timbre Type Specific Operation 5
3 Controlling Send/Receive of MIDI Messages in Each Instrument Part 5
4 Conditions that Disable Message Send and Receive 5
II Channel Message 6
5 Note Off 6
6 Note On 6
7 Control Change 6
7.1 BankSelect(00H,20H) ..................................... 6
7.2 Modulation(01H) ........................................ 7
7.3 PortamentoTime(05H) ..................................... 7
7.4 DataEntry(06H,26H)...................................... 7
7.5 Volume(07H) .......................................... 8
7.6 Pan(0AH) ............................................ 8
7.7 Expression(0BH) ........................................ 8
7.8 Damper Pedal (Sustain) (40H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7.9 PortamentoOn/Off(41H) .................................... 9
7.10 Sostenuto(42H) ......................................... 9
7.11 SoftPedal(43H)......................................... 10
7.12 FilterResonance(47H)...................................... 10
7.13 ReleaseTime(48H) ....................................... 10
7.14 AttackTime(49H)........................................ 10
7.15 FilterCutoff(4AH) ....................................... 11
7.16 VibratoRate(4CH)....................................... 11
7.17 VibratoDepth(4DH) ...................................... 11
7.18 VibratoDelay(4EH) ...................................... 12
1

7.19 PortamentoControl(54H).................................... 12
7.20 ReverbSendLevel(5BH).................................... 12
7.21 ChorusSendLevel(5DH).................................... 12
7.22 DelaySendLevel(5EH)..................................... 13
7.23 RPN (Registered Parameter Number) LSB/MSB (64H,65H) . . . . . . . . . . . . . . . . 13
7.24 AllSoundOff(78H)....................................... 14
7.25 ResetAllControllers(79H)................................... 14
7.26 AllNotesOff(7BH)....................................... 14
7.27 Omni Mode Off (All Notes Off) (7CH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.28 Omni Mode On (All Notes Off) (7DH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.29 Mono Mode On (Poly Mode Off) (All Notes Off) (7EH) . . . . . . . . . . . . . . . . . . . 15
7.30 Poly Mode On (Mono Mode Off) (All Notes Off) (7FH) . . . . . . . . . . . . . . . . . . . 15
8 Program Change 15
9 Channel Pressure (Aftertouch) 16
10 Pitch Bend Change 16
III System Message 17
11 Active Sensing 17
12 System Exclusive Message 17
12.1 Universal Real Time System Exclusive Message . . . . . . . . . . . . . . . . . . . . . . . . 17
12.2 Universal Non Real Time System Exclusive Message . . . . . . . . . . . . . . . . . . . . . 19
IV Setting Values and Send/ Receive Values 20
13 Setting Value Tables 20
13.1 Off/OnSettingValueTable................................... 20
13.2 Sustain Pedal Setting Value Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
13.3 –64 - 0 - +63 Setting Value Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
13.4 PanSettingValueTable..................................... 20
13.5 Fine Tuning Setting Value Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
13.6 Reverb Type Setting Value Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
13.7 Chorus Type Setting Value Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
V MIDI Implementation Notation 22
14 Value Notation 22
14.1 HexadecimalNotation...................................... 22
14.2 BinaryNotation ......................................... 22
2

Part I
Overview
1 Product Configuration as a MIDI Device
As a MIDI device, this Instrument consists of the System Section, Sound Generator Section, and Per-
formance Controller Section described below. Each of these sections can send and receive specific MIDI
Messages in accordance with its function.
1.1 System Section
The System Section manages the Instrument status and user data.
1.2 Performance Controller Section
The Performance Controller Section performs keyboard play and controller operations, and generates
performance messages. Basically, generated performance messages are sent to external destinations
while also being transmitted to the Sound Generator Section. The channel number of the sent channel
message is in accordance with the Instrument’s MIDI setting. For details about the MIDI setting, see
the Instrument’s User’s Guide.
1.3 Sound Generator Section
The Sound Generator Section mainly performs receive of performance information and sound source
setting information. It consists of a common part that does not depend on the channel and a musical
instrument part that is independent of each channel.
1.3.1 Sound Generator Common Block
The common block consists of system effects, master control, etc. These can be controlled by effect
function, or general universal system exclusive messages.
1.3.2 Instrument Part Block
The instrument part section is devided into A, B, C group for every 16 parts, and it consists of a total of
48 parts. The settings of each part can be changed using channel messages. Of these, only the C group
can be controlled by external channel messages.
The functions assigned to each part are shown below.
3

Port Part number MIDI Receive Ch MIDI Transmit ch Assigned Function Details
A 01 - 1-16 Upper1/Arpeggiator -
A 02 - 1-16 Upper2 -
A 03 - 1-16 Lower1 -
A 04 - - - -
A 05 - 1-16 Auto Harmonize -
A 06 - 6 - -
A 07 - 7 - -
A 08 - 8 Metronome -
A 09 - 9 Accomp Percussion
A 10 - 10 Accomp Drum/Metronome
A 11 - 11 Accomp Bass
A 12 - 12 Accomp Chord1
A 13 - 13 Accomp Chord2
A 14 - 14 Accomp Chord3
A 15 - 15 Accomp Chord4
A 16 - 16 Accomp Chord5
Port Part number MIDI Receive Ch MIDI Transmit Ch Assigned Function Details
B 17 - - Auto
Play/Recorder
System Track Up-
per1/Arpeggiator
B 18 - - Auto
Play/Recorder
System Track
Upper2
B 19 - - Auto
Play/Recorder
System Track
Lower1
B 20 - - - -
B 21 - - Auto
Play/Recorder
System Track Auto
Harmonize
B 22 - - - -
B 23 - - - -
B 24 - - Pre count -
B 25 - - - -
B 26 - - - -
B 27 - - - -
B 28 - - - -
B 29 - - - -
B 30 - - - -
B 31 - - - -
B 32 - - - -
4

Port Part number MIDI Receive Ch MIDI Transmit Ch Assigned Function Details
C 33 1 - MIDI/Auto
Play/Recorder
Recorder Solo
Track1
C 34 2 - MIDI/Auto
Play/Recorder
Recorder Solo
Track2
C 35 3 - MIDI/Auto Play -
C 36 4 - MIDI/Auto Play -
C 37 5 - MIDI/Auto Play -
C 38 6 - MIDI/Auto Play -
C 39 7 - MIDI/Auto Play -
C 40 8 - MIDI/Auto Play -
C 41 9 - MIDI/Auto Play -
C 42 10 - MIDI/Auto Play -
C 43 11 - MIDI/Auto Play -
C44 12 -MIDI/Auto Play -
C 45 13 - MIDI/Auto Play -
C 46 14 - MIDI/Auto Play -
C 47 15 - MIDI/Auto Play -
C 48 16 - MIDI/Auto Play -
2 Timbre Type Specific Operation
The sound source operation performed for a sound generator instrument receive message may depend
on the value of the Timbre Type (see “About the Timbre Type” in “8 Program Change”) of each part’s
operation mode. For details, see the explanation for each message.
3 Controlling Send/Receive of MIDI Messages in Each Instru-
ment Part
Send and receive of MIDI messages for each instrument part can be controlled by global Instrument
MIDI settings and Instrument-specific system exclusive messages. See the Instrument’s User’s Guide for
details.
4 Conditions that Disable Message Send and Receive
The main conditions when MIDI message send and receive are disabled by the Instrument are thosedescribed
below.
•While the instrument is accessing flash memory.
•While “Wait” or “Bye” are displayed on the LCD screen.
5

Part II
Channel Message
5 Note Off
Format
Message Format: 8nH kkH vvH
9nH kkH 00H(receive only)
n: MIDI Channel Number
kk: Key Number
vv: velocity
Transmit Sent when something is played on the keyboard or when play is performed using the Arpeg-
giator, etc. The key number changes in accordance with on the Transpose function and Octave Shift
function.
Receive Receipt stops a note being sounded by a note on message.
6 Note On
Message Format: 9nH kkH vvH
n: MIDI Channel Number
kk: Key Number
vv: Velocity
Transmit Sent when something is played on the keyboard or when play is performed using the Arpeg-
giator, etc. The key number changes in accordance with on the Transpose function and Octave Shift
function.
Receive Receipt sounds a note of the corresponding instrument part.
7 Control Change
Message Format: BnH ccH vvH
n: MIDI Channel Number
cc: Control Number
vv: Value
For details about messages, see each section of this manual that covers them.
7.1 Bank Select (00H,20H)
6

Message Format: BnH 00H mmH (MSB)
BnH 20H llH (LSB)
n: MIDI Channel Number
mm: MSB Value(Note1)
ll: LSB Value(Transmit:00H, Receive:Ignored)
Note1: For details about the relationship between the MSB value and the tone, see the Tone List that comes with the
Instrument.
Transmit Sent when a tone setup number is selected.
Receive Receipt causes a change in the tone bank number stored in Instrument memory, but the
tone is not actually changed until a Program Change message is received. For details, see “8 Program
Change”.
7.2 Modulation (01H)
Message Format: BnH 01H vvH
n: MIDI Channel Number
vv: Value
Receive Receipt adds, to the tone being sounded, modulation of a depth specified by the value. In
the case of a tone that already has modulation applied, receipt of this message increases the modulation
depth. The modulation effect differs according to the tone being used.
7.3 Portamento Time(05H)
Message Format: BnH 05H vvH
n: MIDI Channel Number
vv: Value
Receive Receipt changes the portamento application time.
7.4 Data Entry (06H,26H)
Message Format: BnH 06H mmH (MSB)
BnH 26H llH (LSB)
n: MIDI Channel Number
mm: MSB Value
ll: LSB Value
Transmit Sent when there is a change to the parameter assigned to RPN.
Receive Receipt changes the parameter assigned to RPN.
7

7.5 Volume (07H)
Message Format: BnH 07H vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when MIDI setting of Accomp MIDI Out set to ON and when part volume is used.
Receive Receipt changes the part volume.
7.6 Pan (0AH)
Message Format: BnH 0AH vvH
n: MIDI Channel Number
vv: Value(Note1)
Note1: For information about the relationship between setting values and send/receive values, see “13.4 Pan Setting Value
Table” in “IV Setting Values and Send/Receive Values”.
Transmit Sent When MIDI setting of Accomp MIDI Out set to ON and when automatic accompani-
ment is used.
Receive Receipt changes the pan of the corresponding part.
7.7 Expression (0BH)
Message Format: BnH 0BH vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompani-
ment is used.
Receive Receipt changes the Expression value.
7.8 Damper Pedal (Sustain) (40H)
Message Format: BnH 40H vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when a pedal that has a sustain (damper) function is operated.
Receive Receipt performs an operation equivalent to a sustain pedal operation.
8

Timbre Type Specific Operation This operation differs in accordance with the Timbre Type (see
“About the Timbre Type” in “8 Program Change”) setting.
•Timbre Type: Melody,Hex Layer
Sustain off/on control is performed in accordance with the value of the received message. For
information about the relationship between setting values and send/receive values, see the 13.1
Off/On Setting Value Table inIV Setting Values and Send/Receive Values .
•Timbre Type: Piano
Continuous control of the following is performed in accordance with the value of the received
message.
–Piano note decay rate
For information about the relationship between setting values and send/receive values, see13.2
Sustain Pedal Setting Value Table inIV Setting Values and Send/Receive Values. 
•Timbre Type: LM (Linear Morphing) Piano
Continuous control of the following is performed in accordance with the value of the received
message.
–Piano note decay rate
–Resonance characteristics and decay rate of Damper Resonance effect resonance note
see13.2 Sustain Pedal Setting Value Table inIV Setting Values and Send/Receive Values. 
•Timbre Type: Drum
The received message does not affect sound source operation.
7.9 Portamento On/Off(41H)
Message Format: BnH 41H vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.1 Off/On Setting
Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Receive Receipt changes the portamento on/off setting.
7.10 Sostenuto (42H)
Message Format: BnH 42H vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.1 Off/On Setting
Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when a pedal that has a sostenuto function is operated.
9

Receive Receipt performs an operation equivalent to a sostenuto pedal operation.
7.11 Soft Pedal (43H)
Message Format: BnH 43H vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.1 Off/On Setting
Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when a pedal that has a soft function is operated.
Receive Receipt performs an operation equivalent to a soft pedal operation.
7.12 Filter Resonance(47H)
Message Format: BnH 47H vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompani-
ment is used.
Receive Receipt changes the filter resonance intensity.
7.13 Release Time (48H)
Message Format: BnH 48H vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.3 –64 - 0 - +63
Setting Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompani-
ment is used.
Receive Receipt makes a relative change in the time it takes for a note to decay to zero after a key is
released.
7.14 Attack Time (49H)
Message Format: BnH 49H vvH
n: MIDI Channel Number
vv: Value (Note1)
10

Note1: For information about the relationship between setting values and send/receive values, see the “13.3 –64 - 0 - +63
Setting Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompani-
ment is used.
Receive Receipt makes a relative change in the time it takes for a note to rise to its maximum level.
7.15 Filter Cutoff (4AH)
Message Format: BnH 4AH vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.3 –64 - 0 - +63
Setting Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompani-
ment is used. (PX-S3000)
Receive Receipt changes the filter cut-off frequency.
7.16 Vibrato Rate (4CH)
Message Format: BnH 4CH vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.3 –64 - 0 - +63
Setting Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Receive Receipt changes the note vibrato rate.
7.17 Vibrato Depth (4DH)
Message Format: BnH 4DH vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.3 –64 - 0 - +63
Setting Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Receive Receipt changes the depth of pitch modulation.
11

7.18 Vibrato Delay (4EH)
Message Format: BnH 4EH vvH
n: MIDI Channel Number
vv: Value (Note1)
Note1: For information about the relationship between setting values and send/receive values, see the “13.3 –64 - 0 - +63
Setting Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Receive Receipt changes the time it takes until note vibrato starts.
7.19 Portamento Control(54H)
Message Format: BnH 54H vvH
n: MIDI Channel Number
vv: Source Key Number
Receive Receipt of this message first stores the Source Note Number for the next note. When the next
Note On is received, the portamento effect is applied to the note using this Source Note Number as the
pitch start point and the Note On event key number as the end point. If there already is a note being
sounded by Source Note Number at this time, the new note on is not performed and the portamento
effect is applied to the pitch of the note being sounded. That is to say that legato play is performed.
7.20 Reverb Send Level (5BH)
Message Format: BnH 5BH vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when GM tone is selected.
Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompaniment is
used.
Receive Receipt changes the reverb send level of the corresponding part.
7.21 Chorus Send Level (5DH)
Message Format: BnH 5DH vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when chorus type is selected.
Sent when GM tone is selected.
Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompaniment is
used.
Receive Receipt changes the chorus send level of the corresponding part.
12

7.22 Delay Send Level (5EH)
Message Format: BnH 5EH vvH
n: MIDI Channel Number
vv: Value
Transmit Sent when GM tone is selected.
Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompaniment is
used.
Receive Receipt changes the delay send of the corresponding part.
7.23 RPN (Registered Parameter Number) LSB/MSB (64H,65H)
Message Format: BnH 64H llH (LSB)
BnH 65H mmH (MSB)
n: MIDI Channel Number
ll: LSB Value
mm: MSB Value
7.23.1 Pitch Bend Sensitivity
Message Format: BnH 64H 00H
BnH 65H 00H
BnH 06H mmH
BnH 26H llH
n: MIDI Channel Number
mm: MSB Value(00H - 18H)
ll: LSB Value(Transmit:00H, Receive:Ignored)
Transmit Sent when Pitch Bend Range is changed.
Receive Receipt changes Pitch Bend Range of the corresponding part.
7.23.2 Channel Fine Tuning
Message Format: BnH 64H 01H
BnH 65H 00H
BnH 06H mmH
BnH 26H llH
n: MIDI Channel Number
mm: MSB Value
ll: LSB Value
Receive Receipt changes the fine tuning of the corresponding part.
13

7.23.3 Channel Coarse Tuning
Message Format: BnH 64H 02H
BnH 65H 00H
BnH 06H mmH
BnH 26H llH
n: MIDI Channel Number
mm: MSB Value(28H - 58H)
ll: LSB Value(Transmit:00H, Receive:Ignored)
Receive Receipt changes the coarse tune of the corresponding part. Does not affect sound source
operation when the Timbre Type (see “About the Timbre Type” in “8 Program Change”) is Drum.
7.23.4 RPN Null
Message Format: BnH 64H 7FH
BnH 65H 7FH
n: MIDI Channel Number
Transmit Sent when an operation to send RPN messages is performed.
Receive Receipt de-selects RPN.
7.24 All Sound Off (78H)
Message Format: BnH 78H 00H
n: MIDI Channel Number
Transmit Sent when MIDI send related settings are changed.
Receive Receipt stops all voices that are sounding.
7.25 Reset All Controllers (79H)
Message Format: BnH 79H 00H
n: MIDI Channel Number
Transmit Sent when MIDI send related settings are changed.
Receive Receipt initializes each performance controller.
7.26 All Notes Off (7BH)
Message Format: BnH 7BH 00H
n: MIDI Channel Number
Receive Receipt releases (key release) all voices that are sounding.
14

7.27 Omni Mode Off (All Notes Off) (7CH)
Message Format: BnH 7CH 00H
n: MIDI Channel Number
Receive Receipt performs the same operation as when All Notes Off is received.
7.28 Omni Mode On (All Notes Off) (7DH)
Message Format: BnH 7DH 00H
n: MIDI Channel Number
Receive Receipt performs the same operation as when All Notes Off is received.
7.29 Mono Mode On (Poly Mode Off) (All Notes Off) (7EH)
Message Format: BnH 7EH 00H
n: MIDI Channel Number
Receive Receipt performs the same operation as when All Notes Off is received.
7.30 Poly Mode On (Mono Mode Off) (All Notes Off) (7FH)
Message Format: BnH 7FH 00H
n: MIDI Channel Number
Receive Receipt performs the same operation as when All Notes Off is received.
8 Program Change
Message Format: CnH ppH
n: MIDI Channel Number
pp: Program Number (Note1)
Note1: For details about the relationship between the program number and the tone, see the Tone List that comes with the
Instrument.
Transmit Sent when a tone.
Receive Receipt changes the ton of the corresponding part. The selected tone is determined by the
program value of this message and the Bank Select message value received prior to this message.
15

About the Timbre Type Tones that are selected by each Instrument part have an attribute that
depends on the sound source operation type. This attribute is called the “timbre type,” which is one of
the types described below.
•Melody
This timbre type optimizes for normal melody tones. The damper pedal performs on/off operations.
•Piano
This Timbre Type is for piano tones. The decay rate of the voice being sounded is seamlessly
altered in accordance with the depressed amount of damper pedal. The method for producing
sound in response to the note messages also is different from that of the melody Timbre Type, and
operation is optimized for piano.
•LMPiano
This Timbre Type is for Linear Morphing piano tones. The decay rate of the voice being sounded
and Damper Resonance effect characteristics are seamlessly altered in accordance with the de-
pressed amount of damper pedal. The method for producing sound in response to the note messages
also is different from that of the melody Timbre Type, and operation is optimized for piano.
•Drum
This setting optimizes for drum sounds. The damper pedal does not function. The Damper Pedal
(Sustain), Channel Coarse Tune, and Master Coarse Tune messages are ignored if they are received.
9 Channel Pressure (Aftertouch)
Message Format: DnH vvH
n: MIDI Channel Number
vv: Value
Receive Receipt adds, to the tone being sounded, modulation of a depth specified by the value. In
the case of a tone that already has modulation applied, receipt of this message increases the modulation
depth. The modulation effect differs according to the tone being used.
10 Pitch Bend Change
Message Format: EnH llH mmH
n: MIDI Channel Number
ll: Value LSB
mm: Value MSB
Transmit Sent when the pitch bend wheel is operated.
Sent when MIDI setting of Accomp MIDI Out set to ON and when automatic accompaniment is
used.
Receive Receipt changes the pitch of the currently sounding note. The range of the pitch change
depends on the Pitch Bend Range value setting.
16

Part III
System Message
11 Active Sensing
Message Format: FEH
Transmit Sent periodically.
Receive Once this message is received, the Active Sensing mode is entered. If no MIDI message is
received for a specified amount of time, voices being sounded by this Instrument’s sound source are
released, the controller is reset, and the Active Sensing mode is exited.
12 System Exclusive Message
Message Format: F0H iiH 7FH....F7H
ii: ID Number
The Instrument sends and receives standard universal system exclusive messages.
ID Number The ID numbers handed by this Instrument are shown below.
ID Number ID Name
7EH Non Real Time System Exclusive Message
7FH Real Time System Exclusive Message
12.1 Universal Real Time System Exclusive Message
Message Format: F0H 7FH 7FH....F7H
12.1.1 Master Volume
Message Format: F0H 7FH 7FH 04H 01H llH mmH F7H
ll: LSB Value(Receive:Ignored)
mm: MSB Value
Receive Receipt changes the Song Volume.
12.1.2 Master Fine Tuning
Message Format: F0H 7FH 7FH 04H 03H llH mmH F7H
ll: LSB Value(Note1)
mm: MSB Value(Note1)
Note1: For information about the relationship between setting values and send/receive values, see “13.5 Fine Tuning Setting
Value Table” in “IV Setting Values and Send/Receive Values” of this document.
17

Transmit This message is sent when the tuning setting is changed.
Receive Receipt changes the Master Fine Tuning parameter.
s
12.1.3 Master Coarse Tuning
Message Format: F0H 7FH 7FH 04H 04H llH mmH F7H
ll: LSB Value(Transmit:00H,Receive:Ignored)
mm: MSB Value(28H - 58H)
Receive Receipt changes the Patch Master Coarse Tuning parameter.
12.1.4 Reverb Type
Message Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 01H 00H vvH F7H
vv: Value(Note1)
Note1: For information about the relationship between setting values and send/receive values, see “13.6 Reverb Type Setting
Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when Hall Simulator/Reverb Type is changed.
Receive Receipt changes the reverb type.
12.1.5 Reverb Time
Message Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 01H 01H vvH F7H
vv: Value
Receive Receipt changes the Reverb duration.
12.1.6 Chorus Type
Message Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 02H 00H vvH F7H
vv: Value(Note1)
Note1: For information about the relationship between setting values and send/receive values, see “13.7 Chorus Type Setting
Value Table” in “IV Setting Values and Send/Receive Values” of this document.
Transmit Sent when Chorus Type is changed.
Receive Receipt changes the Chorus Type.
12.1.7 Modulation Rate
Message Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 02H 01H vvH F7H
vv: Value
18

Receive Receipt changes the Chorus Rate.
12.1.8 Modulation Depth
Message Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 02H 02H vvH F7H
vv: Value
Receive Receipt changes the chorus level setting.
12.1.9 Send To Reverb
Message Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 02H 04H vvH F7H
vv: Value
Receive Receipt changes the Chorus Sent To Reverb setting.
12.2 Universal Non Real Time System Exclusive Message
Message Format: F0H 7EH 7FH....F7H
12.2.1 GM System On
Message Format: F0H 7EH 7FH 09H 01H F7H
Receive Receipt puts the sound source into a GM sound source mode.
12.2.2 GM System Off
Message Format: F0H 7EH 7FH 09H 02H F7H
Receive Receipt changes the sound source setting to the Instrument presetting.
12.2.3 GM2 System On
Message Format: F0H 7EH 7FH 09H 03H F7H
Receive Though the Instrument does not support GM2, receipt of the GM2 System On message has
the same result as receipt of the GM System On message.
19

Part IV
Setting Values and Send/ Receive Values
13 Setting Value Tables
13.1 Off/On Setting Value Table
Transmit Value Receive Value Parameter
00H 00H - 3FH Off
7FH 40H - 7FH On
13.2 Sustain Pedal Setting Value Table
Transmit Value Receive Value Parameter
- 00H Off
: : (continuous)
- 7FH Full
13.3 –64 - 0 - +63 Setting Value Table
Transmit Value Receive Value Parameter
00H 00H -64
: : :
40H 40H 0
: : :
7FH 7FH +63
13.4 Pan Setting Value Table
Transmit Value Receive Value Parameter
00H 00H Left
: : :
40H 40H Center
: : :
7FH 7FH Right
20