Casio QT-6000 Installation guide

Training manual
QT-6000
Smart Touch Terminal
October 2004

2
QT-6000 Training Manual
Chapter 1 Hardware and Cable Specifications
Chapter 2 Loading the IPL Via CF Card and PC
& Setting up the In-line network
Chapter 3 Initialising the Terminal
Chapter 4 Memory Allocation
Chapter 5 Function Keys
Chapter 6 Setting up shared check tracking
Chapter 7 Setting up floating clerk interrupt
Chapter 8 Setting up printing & shared printing
Chapter 9 Setting up RF Communications
Chapter 10 New functions and features and Memory
Chapter 11 New Check Tracking & Interrupt functions
Chapter 12 Other new functions
Chapter 13 Customer File and Invoice number
Chapter 14 Downloading graphic logo’s bitmaps and sounds

3
CHAPTER 1
HARDWARE CONFIGURATION
General Configuration Front View
General Configuration Back View

4
QT-6000 Hardware Specification
QT-6000 Standard RAM is 32mb (16mb usable)
Flash Memory used for IPL data is 16mb
The In-Line system used is Ethernet
The Ethernet communications Board comes as standard when
purchasing the QT-6000 terminal
You can connect up to three external printers per terminal
You can connect up to two drawers

5
Layout of Com ports on the QT-6000
As you can see from the diagram above there are 6 Com ports
These are used for the following tasks
Com Port 1 = PC / Modem
Com Port 2 = Scanner
Com Port 3 = Remote display
Com Port 4 = My Printer 1
Com Port 5 = My Printer 2
Com Port 6 = My Printer 3
In addition to the Com ports you can also find
Ethernet In-Line connector
Volume control switch
Two drawer connectors
An External Microphone connector
An External Speaker connector

6
QT-6000 Optional extra’s
Card Swipe
Rear display
Dallas keys and lock

7
QT-6000 In-Line (Ethernet)
Configuration 1
Terminal to Terminal (You must use a Hub)
Configuration 2
Multiple Terminals 10 BASE-T
Configuration 3
Multiple Terminals 100 BASE-T

8
In-Line Maximum Configurations
You can have up to 12 terminals In-Line when using
floating check tracking or floating clerk interrupt.
You can have up to 32 terminals In-Line if you are not
using check tracking or clerk interrupt.
You can have a maximum of 8 Printers shared thought out
the Ethernet network.
All Terminals must always be connected to a hub
You must use the Netgear FS108 hub.
Note: will do not support the cross over cat-5 cable
between two terminals. When connecting more than one
terminal you must use a Hub.

9
In-Line specifications and cable lengths
Wiring configuration for Cat-5
All Terminal need to be connected to the hub as shown below
Cat-5 Wiring diagram
This is how the cables should be wired and also the specification
of the cable which should be used

10
Connecting printers
It is possible to have 3 printers per terminal if the terminals are
stand-alone and there is a maximum of 8 terminals for an In-line
situation
Supported Printers
Epson Thermal TM-88 / UP-350 / 360
Epson Dot Matrix TM-U210 / U-220 / UP-250
Printer wiring diagram
D Sub 9 Pin Female D Sub 25 Pin Male
3TXD RXD3
6DSR DTR20
8CTS RTS4
2RXD TXD2
4DTR DSR6
5SG SG7

11
Casio PC Interface
Online Specifications
PC configurations
It is now possible to use either a serial or TCP/IP connection
Serial Connection
TCP/IP Connection

12
QT-6000 to Modem wiring diagram
(2)
(3)
QT-6000 to PC wiring diagram

13
CHAPTER 2
LOADING THE IPL Via CF CARD / PC
& Setting up the Ethernet network (TCP/IP)
Required equipment: A PC or a CF card
A PRL-CB2 (RS232 / Laplink cable/Cat-5 cable and hub)
Auto Load via CF card
Copy the IPL data to the route directory of the San Disk CF card
via PC
1.
Insert the CF card in to the CF card reader of the PC
2.
Copy the IPL data to the CF card

14
Follow the procedure below to load the IPL data to the QT-6000
(1) Insert the CF card into the top of the terminal
(2) Switch the terminal off and hold down the INIT switch the
terminal will then will ask you to push the INIT Switch again
to start the load of the IPL
(3) Press the INIT Switch and the IPL will start to load
(4) After the IPL has loaded the QT-6000 will ask for a Mac/Init
code enter 10000 for UK and then press “ok”
After you have entered 10000 the QT-6000 will come up with
the TCP/IP network screen. This screen is shown below

15
Master Terminal Settings
1. Select terminal ID 1
2. This will automatically make this terminal the DHCP server
3. Select yes to confirm your options
The DHCP server issues the IP addresses to all the other
terminals in the In-line network provided that you select auto
Settings for all other terminals in the In-Line network
Terminal 2
Enter the terminal numbers in sequential order
Set IP Address to Auto and select yes

16
Terminal 3
Enter the terminal numbers in sequential order
Set IP Address to Auto and select yes
This will give the following IP Address’s to the QT-6000’s
Master 192.168.000.001
Terminal 2 192.168.000.050
Terminal 3 192.168.000.051
After this TCP/IP selection the Mac screen will now be displayed

17
Loading the IPL via PC
Install CV-10 to your PC
Plug your PRL-CB2 (RS-232 standard lap link cable) in to Com 1
Copy the QT-6000 IPL file to the CVW folder
Go in to the CVW folder and double click on C_comw Icon
Double click on C_Comw Icon

18
You should see this screen
Tasks On the PC
(1) Set the Com direction to IPL
(2) Set Communication line to online
(3) Select profile name QT-6000.INI
(4) Select the dos file name to Qt-6000.IPL
(5) Press the add key the screen should look the same as the
above

19
On the cash register
(1) Initialise the Terminal with 44449999 Sub-Total
(2) Select IPL Com Port 1
(3) Select speed 115200
(4) Select Start

20
You should now see the following on the screen of the terminal
IPL : COM1 PORT
115200 bps
Waiting for IPL
Now select “OK” from the PC
The IPL will now be loaded to your terminal
After the IPL has loaded you will see the Mac screen
The next chapter of this manual will guide you though the Mac
procedure for the QT-6000