Cavius 2107-001 User manual

PLEASE READ THIS USER GUIDE CAREFULLY
PHOTOELECTRIC SMOKE ALARM
THE WORLD’S SMALLEST

PLEASE READ THE USER GUIDE CAREFULLY BEFORE
INSTALLATION AND RETAIN FOR FUTURE USE.
CAVIUS Photoelectric Smoke Alarm
Part Code: 2107-002/10022/10026
Model: 2107-001
Recess Kit Part Code: 11014
For large text option and maintenance guide visit
cavius.co.nz/resources or cavius.com.au/resources

Contents
Technical information ______________________________________________________ 2
The best areas to install a smoke alarm ______________________________________ 4
Areas where NOT to install smoke alarms ____________________________________ 5
Placement ________________________________________________________________ 6
How to set up and connect alarms (without GATEWAY HUB or App) ____________ 8
How to set up and connect alarms using the GATEWAY HUB and App _________ 11
Installation of smoke alarm ________________________________________________ 12
Test function _____________________________________________________________ 16
Normal mode _____________________________________________________________ 18
Alarm mode ______________________________________________________________ 18
Hush function ____________________________________________________________ 19
Add extra device _________________________________________________________ 20
Low battery indicator _____________________________________________________ 21
Functional Information ____________________________________________________ 22
Warranty _________________________________________________________________ 24
1

TECHNICAL INFORMATION
The maximum number of CAVIUS Wireless Family alarms that can be
interconnected within a house group are 32.
Please note: These must be alarms from the CAVIUS Wireless Family range.
The distance between interconnected alarms depends on the house layout
and they should always be tested after installation. It is not advised to be
more than 10m distance between two alarms.
Diameter: 78mm
Height: 43mm
2

The alarm is powered by two 3v CR123A lithium batteries.
Interconnected by RF: 926.365 MHz
Complies to standards: AS3786:2014/RCM
3
Alarm condition aural signal pattern according to ISO 8201.

1. The best areas to install an alarm:
 • Installalarmsoneachoorofthehouse,inhallwaysandstairways.
 • Alarmsineachroomsuchasbedroomsandlivingrooms.
4

2. Areas where NOT to install smoke alarms:
 • Industyrooms
 • Atthetopofahighpointedceiling,incornersofaroom,andwithin
50cm of where a ceiling and wall join.
 • Inroomswherethetemperaturegoesoutside+4cto38corabove90%
relative humidity not condensing.
 • Inkitchens,garages,laundries,ortooclosetoreplaces;areaswhere
  eitherdampness,gasesorheatcouldoccur.Placethealarmwhereitis
reachable in order to test the battery and for maintenance.
5

3. Placement:
The smoke alarm is designed to be installed on a ceiling (preferred) or wall.
Ceiling installation:
The smoke alarm should be a minimum of 50cm from the wall.
6
Minimum 50cm
from peak.
Ceiling
Wall

For catheral or peak ceiling or wall installation:
Forcathedralorpeakceiling;aminimumof50cmfromthepeak
7
Minimum 50cm
from peak.
Ceiling Ceiling
Forwallinstallation;aminimumof30cmandmaximumof50cmfromthe
ceiling.
Minimum 30cm and
maximum 50cm from
ceiling
Wall

4. How to set up and connect alarms (without GATEWAY HUB or App):
All alarms that need to be connected in the house should be put into ‘Link Mode’
by sliding the switch on the back of the alarm to the ‘Link Mode’ position.
8
LINK MODE
NORMAL MODE

9
Press the button on the top of one alarm only. This alarm will become the
‘Master’andwillstartsendingoutaspecichousecodetotheotheralarms
(takenoteofwhichalarmisthe‘Master’,youmayneedthisforaddingextra
devicesinfuture).TheredLEDwillash.

10
Astheotheralarmsreceivethespecichousecode,theywillalsoashthe
LED light.
WhenallalarmsashtheredLED,theyareconnectedandcanbeswitched
out of ‘Link Mode’ and installed.

11
5. How to set up and connect
alarms using the GATEWAY HUB
and App:
Ensure the CAVIUS GATEWAY HUB
is plugged into your router and the
wall socket.
Download the CAVIUS App from the
Apple App Store or Google Play.
Launch the app from your smart-
phoneortablet,andjustfollow
the instructions for setting up your
alarms.
GATEWAY HUB
ROUTER

12
MARK UP
SCREW HOLES
WITH A PEN
6. Installation of smoke alarm:
Info: The label on the product must
not be removed due to
important information.
Option 1 – Standard base
1. Use the mounting
base ring to mark the
screw holes on the ceiling.

13
USE THE
ENCLOSED
SCREWS AND
PLUGS FOR
INSTALLATION
CLICK THE SMOKE
ALARM FIRMLY INTO
THE BASE TO ACTIVATE

14
Option 2 – Recess Kit
1. Place the Cover Ring on the area where you wish to install the smoke
alarm,tracearoundtheinsideofthering.
HOLE SAW
DRILL REQUIRED.
81mm - 85mm

15
INSERT RECESS KIT
MOUNTING BASE INTO
THE HOLE AND SECURE
WITH SCREWS
PLACE COVER RING
AROUND THE RECESS
KIT MOUNTING BASE
CLICK THE SMOKE
ALARM FIRMLY INTO
THE BASE TO ACTIVATE
2. Using your hole saw
(81mm-85mm),cuta
hole into the surface.
CAUTION: Ensure
there is no wiring or any
electrical equipment
behind the surface you
are drilling your hole into.

16
7. Test function:
Afterinstallation,andatleastonceperquarter,testallofyouralarmstoensure
they are operating correctly and are within range of each other.
ItisrecommendedtocheckvisuallyeveryweekiftheLEDashescorrectly
(every 48sec.)
Press the test button on any alarm for at least 6.5 seconds (count 2 sets of
3soundsweeps).Thiswillsendoutatestsignalfromthealarm;allother
connected alarms should receive the signal within a short time. The alarms will
emitashortbeepandtheLEDwillashevery8secondsfor2minutes.
You can also conduct the interconnection test through the CAVIUS App
(if you have the GATEWAY HUB and App set up).

17
When the test signal is sent out, the alarms will respond in two ways:
1. A single beep every 8 seconds indicates that the alarms are connected
and functioning.
2. Three short beeps every 8 seconds indicates a smoke sensor fault.
The alarm should be cleaned by running the vacuum (on a low setting)
around the smoke alarm chamber and tested again.
Oncethealarmshaveindicatedtheyareinterconnected;thebeepscanbe
stopped on each alarm with a short press of the test button.
TIP:Itissafetocoverthesoundoutputholewithyourngerduringthe
testing to minimise the sound level emitted.
Ifanyproblemsoccurduringtesting,visitwww.cavius.co.nzor
www.cavius.com.au for further trouble shooting.

18
8. Normal mode:
InnormalmodetheLEDwillashevery48secondstoshowthealarmis
functioning.
9. Alarm mode:
Whenaconcentrationofsmokeisdetected,thesmokealarmwillgointo
‘AlarmMode’.ItwillsoundthealarmsignalandtheLEDwillash.Pleasenote
thatonlythesourcealarm’sLEDwillash,soitcanbeidentied.
The smoke alarm will also transmit the alarm signal to the other connected
alarms,whichwillalsosoundthealarmsignalafterashortdelay.
A notication will be sent to your smartphone or tablet through the
CAVIUS App (if you have the GATEWAY HUB and App set up).