Cavius 3104-001 User manual

PLEASE READ THIS USER GUIDE CAREFULLY
THERMAL HEAT ALARM
THE WORLD’S SMALLEST

Contents
Technical information ______________________________________________________ 2
The best areas to install a heat alarm_________________________________________ 4
Areas where NOT to install heat alarms_______________________________________ 5
Placement ________________________________________________________________ 6
How to set up and connect alarms __________________________________________ 7
Installation of heat alarm __________________________________________________ 10
Test function _____________________________________________________________ 14
Normal mode _____________________________________________________________ 16
Alarm mode ______________________________________________________________ 16
Hush function ____________________________________________________________ 17
Add extra device _________________________________________________________ 18
Low battery indicator _____________________________________________________ 19
Functional Information ____________________________________________________ 20
Warranty _________________________________________________________________ 22
PLEASE READ THE USER GUIDE CAREFULLY BEFORE
INSTALLATION AND RETAIN FOR FUTURE USE.
CAVIUS Thermal Heat Alarm
Part Code: 3104-003
Model: 3104-001
Recess Kit Part Code: 11011
For large text option and maintenance guide visit
cavius.co.nz/resources or cavius.com.au/resources
1

The alarm is powered by one 3v CR123A lithium battery.
Interconnected by RF: 926.365 MHz
Complies to standards: EN60065/EN54-5/RCM
TECHNICAL INFORMATION
The maximum number of CAVIUS Wireless Family alarms and devices that
can be interconnected within a house group are 1000.
Please note: These must be alarms or devices from the CAVIUS Wireless
Family range.
The distance between interconnected alarms depends on the house layout
and they should always be tested after installation. It is not advised to be
more than 10m distance between two alarms.
Diameter: 65mm
Height: 44mm
2 3
Alarm condition aural signal pattern according to ISO 8201.

1. The best areas to install an alarm:
 • Installalarmsoneachoorofthehouse,inhallwaysandstairways.
 • Alarmsineachroomsuchasbedroomsandlivingrooms.
2. Areas where NOT to install heat alarms:
 • Bedrooms
 • Lounge
 • Diningroom
 • Hallway
 • Familyroom
NOTE: Thermal heat alarms are designed to be installed in areas where
amingresoccuroversmoulderingres.
45

3. Placement:
The thermal heat alarm is area
specic.Thealarmshouldbe
placed on the ceiling and near
wherethepotentialrerisksmay
occur.
Never install directly above the
oven / hob / stove.
6 7
For kitchen installation:
CEILING
MAXIMUM 100cm
4. How to set up and connect alarms:
Allalarmsthatneedtobeconnectedinthehouseshouldbeputinto‘LinkMode’
byslidingtheswitchonthebackofthealarmtothe‘LinkMode’position.
2
LINKMODE
1
NORMALMODE

89
Press the button on the top of one alarm only. This alarm will become the
‘Master’andwillstartsendingoutaspecichousecodetotheotheralarms
(takenoteofwhichalarmisthe‘Master’,youmayneedthisforaddingextra
devicesinfuture).TheredLEDwillash.
Astheotheralarmsreceivethespecichousecode,theywillalsoashthe
LEDlight.
WhenallalarmsashtheredLED,theyareconnectedandcanbeswitched
outof‘LinkMode’andinstalled.

10 11
MARK UP
SCREW HOLES
WITH A PEN
5. Installation of heat alarm:
Info: The label on the product must
not be removed due to
important information.
Option 1 – Standard base
1. Use the mounting
 baseringtomarkthe
screw holes on the ceiling.
USE THE
ENCLOSED
SCREWSAND
PLUGS FOR
INSTALLATION
CLICK THE HEAT
ALARM FIRMLY INTO
THEBASETOACTIVATE

12 13
INSERT RECESS KIT
MOUNTINGBASEINTO
THEHOLEANDSECURE
WITH SCREWS
PLACE COVER RING
AROUNDTHERECESS
KITMOUNTINGBASE
CLICK THE HEAT ALARM
FIRMLY INTO
THEBASETOACTIVATE
Option 2 – Recess Kit
1.PlacetheCoverRingontheareawhereyouwishtoinstalltheheatalarm,
trace around the inside of the ring.
2. Using your hole saw
(68mm-71mm),cuta
hole into the surface.
CAUTION: Ensure
there is no wiring or any
electrical equipment
behind the surface you
are drilling your hole into.
HOLE SAW
DRILL REQUIRED.
68mm - 71mm

1514
When the test signal is sent out, the alarms will respond in two ways:
1. A single beep every 8 seconds indicates that the alarms are connected
and functioning.
2. Three short beeps every 8 seconds indicates a heat sensor fault.
The alarm should be cleaned by running the vacuum (on a low setting)
around the heat alarm chamber and tested again.
Once the alarms have indicated they are interconnected; the beeps can be
stopped on each alarm with a short press of the test button.
TIP:Itissafetocoverthesoundoutputholewithyourngerduringthe
testing to minimise the sound level emitted.
Ifanyproblemsoccurduringtesting,visitwww.cavius.co.nzor
www.cavius.com.au for further trouble shooting.
6. Test function:
Afterinstallation,andatleastonceperquarter,testallofyouralarmstoensure
they are operating correctly and are within range of each other.
ItisrecommendedtocheckvisuallyeveryweekiftheLEDashescorrectly
(every 48sec.)
Press the test button on any alarm for at least 6.5 seconds (count 2 sets of
3 sound sweeps). This will send out a test signal from the alarm; all other
connected alarms should receive the signal within a short time. The alarms will
emitashortbeepandtheLEDwillashevery8secondsfor2minutes.

16 17
9. Hush function:
Pleasechangeto:Iftheheatalarmsaretosetintoafalsealarmbycooking,
replace,etc.allofthemcanbepausedfor10minutesbypressingthehush
buttonontheoriginatingalarmonly(indicatedbytheashingLED).
Youcanhusheachalarmindividually,howeverthesourcealarmwillcontinue
to sound until hushed.
The reason for this is that it is necessary to locate the source of the alarm
beforeusingthehushfunction.Thisistomakesurethatitisnotalife
threatening situation.
7. Normal mode:
InnormalmodetheLEDwillashevery48secondstoshowthealarmis
functioning.
8. Alarm mode:
Whenarapidandconstantchangeoftemperatureisdetected,theheatalarm
willgointo‘AlarmMode’.ItwillsoundthealarmsignalandtheLEDwillash.
Pleasenotethatonlythesourcealarm’sLEDwillash,soitcanbeidentied.
The heat alarm will also transmit the alarm signal to the other connected
alarms,whichwillalsosoundthealarmsignalafterashortdelay.

1918
10. Add extra device:
All CAVIUS interconnected alarms within the
range can be added to the system as they run on the same frequency and use
the same data protocol. This means that the wireless system can consist of a
combinationofsmokealarms,heatalarms,andsecurityproducts.
Justplacethe‘Master’andnewdeviceinto‘LinkMode’,repeatSection4.
Always test connection to all devices by repeating the test function (Section 7)
after adding devices.
Low battery indicator: Your product has a 5 year battery life.
Whenthebatteryisstartingitsendoflife,ashortbeepwillsoundoutevery
48 seconds for 30 days.
Thealarmeectedbythelowbatterywillonlybeep,nootherconnected
alarms will sound.
Itissafetochangebatteriesinthealarmswithoutgoingthroughthelink
process again – they will not forget the codes during the battery change
process.
Alwaystesttheheatalarmafterclickingintothemountingbase,allow5
seconds before testing.

20 21
Developed & Manufactured by:
Aps
Julsøvej16-DK8600Silkeborg
cavius.com - [email protected]
Manufactured in P.R.C.
Distributor information:
for New Zealand - CAVIUS Nano Ltd.
58aPoplarLane,Papamoa3187,NZ. www.cavius.co.nz
for Australia - CAVIUS Australia PTY Limited
POBox6126,Yatala,QLD4207,Australia.www.cavius.com.au
FUNCTIONAL INFORMATION
Type of alarm: CAVIUS heat alarm is a thermal heat alarm.
Alarm signal: Fire alarm activation is indicated by a series of repeated tones.
Theminimumsoundlevelis85dBat3metres.
Battery: Powered by one replaceable
3vCR123A,1600mAhlithiumbattery.

22 23
Warranty:
CAVIUSprovidesa10-yearwarrantyagainstdefectinfaultymaterialandworkmanship
fromthedateofpurchase,onalldevices.
The warranty applies to reasonable and normal conditions of use only. It does not
includedamageasaresultofmisuse,incorrectinstallation,accidentaldamage,
neglect,unauthoriseddeconstructionordismantlingandanyairborneorother
contamination however this may have occurred.
IfthisproducthasanacknowledgeddefectitmustbereturnedtothenationalCAVIUS
Distributoratthepurchaserscostwiththeproofofpurchase.
Iftheproducthasbecomedefectivewithinthe10-yearwarranty,CAVIUSAPS,
Denmarkwillrepairorreplacetheunitwithoutchargeandsendbacktothepurchaser,
viathenationalDistributorattheDistributorscost.
Theguaranteeexcludeslabourcosts,freightcosts,servicecostsandanyincidental
andconsequentialdamages.Donotattempttorepairorservicethisproductasthis
will invalidate the warranty.
Under some unusual circumstances the presence of high levels of radio spectrum
pollution may result in the batteries within the CAVIUS device not lasting as indicated in
the product sheet. Radio spectrum pollution comprises transmissions inside the band
allocated for alarm devices such as the CAVIUS devices. Such transmissions may
activate the receiver inside the devices for a longer time than is normal in standby.

ThisisnotaspecicproblemforCAVIUSdevicesbutforallsimilarradiolinked
technology powered by batteries. The limited warranty will not cover the battery life
period indicated in the product sheet in these situations.
This warranty is in lieu of any other warranty either expressed or implied.
You can register your CAVIUS devices on our website.
127482 rev2
www.cavius.co.nz |www.cavius.com.au

PLEASE READ THIS USER GUIDE CAREFULLY
THERMAL HEAT ALARM
THE WORLD’S SMALLEST