Cazoner J1 User manual

2
1Product Introduction
CONTACT
Website: http://www.cazoner.com/
Tel: [phone]
Email: [email protected]
Address: A156 4F Niulanqian Building Longhua new District
Shenzhen, China.
Zip code: 518101
THANK YOU FOR READING :)
Sensor
Double alarm
Arc Design
Indicator State Description
Power indicator light on: Working normally
Green light flashes: Self-test and preload start up
Red light flashes: Danger Alarming
Yellow light flashes: fault
Products Schematic Installation Instructions
Installation Location
The detector and the gas stove should be located in the
same indoor space;
The best distance between the detector and the gas
leak source is 1-3 meters.
Point for Attention
Do not install it in the place that too close to the gas
stove!
Do not install it in the place with too much smoke!
3Key Function Operation Guide
Self-test Key:Detecting the sound and light alarm to
see if it is abnormal.
If the ring indicator light or buzzer is abnormal,please
repair it in time.
CAZONER Natural Gas Detector Manual
CAZONER natural gas detector is a household detection
equipment for detecting the leakage of natural gas and
liquefied petroleum gas.When the gas leaks reach to the
concentration of dangerous value in the house, the signal
of the detector's audible and visual alarm will be issued
immediately that promoting you to take effective action
quickly to eliminate the danger so that can avoid the
accidents like fire and explosion effectively.
Made with original cores
The gas-sensing electrodes material is
100% pure platinum precious metal.
Up to 70 dB audible alarm
360° ring warning light
The polycarbonate has been carefully selected
Strictly enforce fire safety standard requirements
Matte process.
The detector is arc design that will be more design
sense and safer without sharp edge. Its line is
soft to add the visual space and could decorate
your indoor space naturally and gracefully.
If the gas is natural gas,install the detector at the distance
of 0.3m from the ceiling and 1-3m from the gas source.
If the gas is LPG,install the detector at the distance of 0.3m
from the floor and 1-3m from the gas source.
No alarm state-->Press the self-test button-->The ring
indicator light flashing green,red,yellow while the buzzer
sounds three times.
The most important is that this design will keep the
detector high sensitive and stable in 7x24 hours.
Do not install it in the place of exhaust fan,doors,
windows,bathrooms and other large airflow or humidity larger!

J1
Natural Gas /LPG
100g
Semiconductor
59mm * 59mm * 40mm
Natural diffusion
AC90~260V
0-100% LEL
180s ± 10s
7%LEL
Visible and Audible alarm
Temperature: -20 to 40
Humidity: ≤ 95% RH (no frost)
70dB
5 years
Model
Applicable Gas
Weight
Overall Dimensions
Sampling Method
Working Voltage
Range
Self-test Time
Alarm presetting
level
Alarm
Working
Environment
Alarm Volume
Lifespan
Sensor Type
56
Failure
Phenomenon
The connection
of the power cord
is not well
Power indicator
has failed
Press the self-test
button without
sound and
light alarm
Circuit failure
No response
to detection
of gas
Pre-boot program
has not over yet
Circuit failure
After the
pre-start
procedure,
the detector has
been in the
alarm state
There are large
amount of volatile
organic compounds
surround
Place the
detector
in a clean
air environment
andrestart the
self-test
program
Long storage
Circuit failure
Please check
thepower cord
connection and
connect it again
Please contact
the seller for
assistance
Please contact
the seller for
assistance
Wait for the
program to
complete the
pre-boot
Please contact
the seller for
assistance
Please contact
the seller for
assistance
Continue to
aging it with
electricity
The green power
indicator does
not light
7
Main Specifications Common faults and solutions
Failure Analysis Solutions
After-sales service and Warranty Policy
4Equipment Maintenance
1. First time to use: Please aging it with electricity for more than
24 hours when first to be used after a long-distance transport
or long storage so that it can keep the best performance.
2.Self-checking period: Please self-test it for every 4-6
months.When you use an known concentration of gas to test
the detector to confirm whether it will work, please be sure the
operation environment is absolutely safe!
3. Cleaning: Please use soft brush,velvet cleaning tools to
clean its face end's dust or oil to ensure its detection hole
breathable so that can keep good display.Please do not use
detergents, bleach or other cleaning liquid to clean it.
4. Indoor use only: Please avoid rain or moisture when use it.
Please avoid it fall down. Do not beat,open or change it,or it
might causes the product failure.
6. Lifespan: The maximum life of the detector is 5 years under
normal situation.Please replace a new one when over the use
of the period.
5. Avoid volatile substances surround: Please do not use
volatile substances like alcohol or hair gel near to the detector.
If this kind of material causes the false report of the detector,
please ventilates promptly so that it can return to the normal
examination condition.
SUPPORT ONE-YEAR FREE REPLACEMENT,BUT CAN NOT ENJOY
THE WARRANTY UNDER THE SITUATION OF NON-NORMAL USE
(FOR EXAMPLE: LIGHTNING, VOLTAGE INSTABILITY, WATER AND
OTHER HUMAN FACTORS)