CBC PT112N User manual

P
PT T1 11 12 2N N/ /P PT T1 11 12 2N N- -X XT T
Vandal Resistant 12x PTZ Dome
UUser Manual
NY: 55 Mall Drive • Commack, NY 11725 [phone]
CA: 21241 S. Western Ave, Suite 160 • Torrance, CA 90503
[phone]
www.computarganz.com

A○
1E
AIntroduction
Features 3
Product & Accessories 5
Parts Name & Functions 7
A○
2E
AInstallation
DIP Switch Setup 8
Installation using Ceiling Mount Bracket 11
Installation using Wall Mount Bracket 12
Installation using Flush Mount Bracket 13
Cabling 14
A○
3E
AOperation
Check Points before Operation 17
Preset and Pattern Function Pre-Check 17
Starting OSD Menu 18
Reserved Preset 18
Preset 19
Swing 19
Pattern 20
Group 21
Other Functions 22
OSD Display of Main Screen 23
A○
4E
AHow to use OSD Menu
General Rules of Key Operation for Menu 24
Main Menu 24
Display Setup 25
Privacy Zone Mask Setup 26
Camera Setup 27
Motion Setup 30
Preset Setup 32
Swing Setup 33
Pattern Setup 34
Group Setup 35
System Initialize 37
A○
5E
ASpecifications
38
Dimensions
39
CONTENTS

Speed Dome Camera Instruction Manual 3
Features
Camera Specifications
zCCD Sensor : 1/4" Super-HAD CCD
zZoom Magnification : ×12 Optical Zoom, ×12 Digital Zoom (Max ×144 Zoom)
zDay & Night Function
zVariable Focus Mode: Auto-Focus / Manual Focus / Semi-Auto Focus.
zIndependent & Simultaneous Camera Characteristic Setup in Preset operation
Advanced Pan/Tilt Functions
zMax. 360°/sec high speed Pan/Tilt Motion
zUsing Vector Drive Technology, Pan/Tilt motions are accomplished with the shortest path. As a result,
time to target view is reduced dramatically and the video stream transfers are natural to watch.
zFor jog operation using a controller, an ultra slow speed of 0.05°/sec can be reached, making it very
easy to relocate camera to the desired target view. Additionally, it is easy to move the camera to a
desired position with zoom-proportional pan/tilt movement.
.
Preset, Pattern, Swing, Group, Privacy Mask and More…
zMax. 127 Presets are assignable and characteristics of each preset can be set up independently, such as
White Balance, Auto Exposure, Label and so on.
zMax. 8 set of Swing actions can be stored. This enables camera to move automatically between two
preset positions at a designated speed.
zMax. 4 Patterns can be recorded and played back. This enables camera to automatically follow any
trajectory preset by joystick as closely as possible.
zMax. 8 set of Group action can be stored. This enables camera to move automatically with a
combination of Preset or Pattern or Swing. A Group is composed of max. 20 entities of Preset/
Pattern/Swings.
zPrivacy Masks are assignable, so as not to intrude on other’s privacy. (8Privacy Zones)
PTZ (Pan/Tilt/Zoom) Control
zWith RS-485 communication, max. of 255 cameras can be controlled at the same time.
zPelco-D or Pelco-P protocol can be selected as a control protocol in the current firmware version.
INTRODUCTION 1
INTRODUCTION 1

Speed Dome Camera Instruction Manual 4
OSD (On Screen Display) Menu
zOSD menu is provided to display the status of camera and to configure the functions interactively.
zThe information such as Camera ID, Pan/Tilt Angle, Alarm Input and Preset can be displayed on screen.
Alarm I/O Functions
z4 alarm sensor Inputs are available.
zTo completely eliminate external electric noise and shock, alarm sensor Input is decoupled from photo
coupler.
zIf an external sensor is activated, camera can be set to move to the corresponding Preset position.
Reserved Presets for Special Purpose
zMost camera characteristics can be set up easily and directly with reserved preset, without entering the
OSD menu. For more information, refer to “Reserved Preset” in this manual.
IP66 (weather resistant) *(PT112N-XT model only).
zThis product has been certified to the IP66 standard for waterproof and spray proof environments. Also
for the same reason it can be protected from dust and rainstorms.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 5
Product & Accessories
Product & Accessories- UPT112N-XT model (outdoor)U.
zMain Body zMount Adapter zGasket(Rubber)
zTerminalBlock zScrews zSix angles wrench
Videocable
Options
zWallMountBracket zCeilingMountBracket zSun shield
INTRODUCTION 1

Speed Dome Camera Instruction Manual 6
Product & Accessories-UPT112N model (indoor)U.
zMain Body zSurface Mount Bracket zScrews & Terminal Block
Options
zIn-Ceiling Mount Bracket zCeilingMountBracket zWall Mount Bracket
INTRODUCTION 1

Speed Dome Camera Instruction Manual 7
Parts Name & Functions
zDome Cover UDo not remove protective vinyl from dome cover before finishing all
installation processes to protect dome cover from scratches or dust.U
zSurface Mount Bracket The surface mount bracket is used for installing either a ceiling mount
or wall mount bracket. Separate the cover first and then attach it
directly to ceiling. Camera must be assembled at the last stage.
zGasket (PT112N-XT
model only)
zLockup Screw
Protect it from dust and rainstorm. Move projecting part of the gasket
which should be placed on the low to main body position
Fixes main unit to surface mount bracket.
zCabling Terminal Block During installation, Power, Video, Communication, Alarm Input cables
are connected on to this cabling terminal block.
Pull out from Surface Mount Bracket and connect to Main Body hook.
zDIP Switch
zFall-proof spring
Adjusts camera ID and protocols.
After installing fall-proof spring on Bracket , hang on the safety ring to
protect the camera from falling
INTRODUCTION 1
Main Unit / Surface Mount Bracket
DIP Switch
Cabling Terminal Block
Back of Main Unit
MountAdapter
Lock-up Screw
Dome Cover
Safety Retention Spring
Main Body
Gasket (PT112N-
XT Model only)

Speed Dome Camera Instruction Manual 8
DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID and communication
protocol.
Camera ID Setup
123456
ON
ON
78
Pin 1 2 3 4 5 6 7 8 Pin 1 2 3 4 5 6 7 8
ID 1 2 4 8 16 32 64 128 ID 1 2 4 8 16 32 64 128
1 on off off off off off off off 11 on on off on off off off off
2 off on off off off off off off 12 off off on on off off off off
3 on on off off off off off off 13 on off on on off off off off
4 off off on off off off off off 14 off on on on off off off off
5 on off on off off off off off 15 on on on on off off off Off
6 off on on off off off off off 16 off off off off on off off off
7 on on on off off off off off 17 on off off off on off off off
8 off off off on off off off off 18 off on off off on off off off
9 on off off on off off off off 19 on on off Off on off off off
10 off on off on off off off off 20 off off on off on off off off
zThe ID number of camera is set using a binary number. Examples
shown below.
zThe range of ID is 1~255. UDo not use 0 as camera IDU. Factor y
default of Camera ID is 1.
zIf you want to control a certain camera, you must match the camera
ID with Cam ID setting of DVR or Controller.
2
INSTALLATION

Speed Dome Camera Instruction Manual 9
Communication Protocol Setup
1234
ON
ON
Reserved for Supplier
zSelect the appropriate Protocol with DIP switch combination.
Switch State
P0
(Pin 1)
P1
(Pin 2)
Protocol
OFF OFF PELCO-D, 2400 bps
ON OFF PELCO-D, 9600 bps
OFF ON PELCO-P, 4800 bps
ON ON PELCO-P, 9600 bps
zIf you want to control using DVR or P/T controller, their protocol must
be identical to camera. Otherwise, you Ucannot Ucontrol the camera.
zIf you changed camera protocol by changing DIP S/W, the change
will be effective after you reboot the camera.
zFactory default of protocol is “Pelco-D, 2400 bps”.
INSTALLATION 2
Pin 1 2 3 4 5 6 7 8 Pin 1 2 3 4 5 6 7 8
ID 1 2 4 8 16 32 64 128 ID 1 2 4 8 16 32 64 128
21 on off on off on off off off 31 on on on on on off off off
22 off on on off on off off off 32 off off off off off on off off
23 on on on off on off off off 33 on off off off off on off off
24 off off off on on off off off 34 off on off off off on off off
25 on off off on on off off off 35 on on off off off on off Off
26 off on off on on off off off 36 off off on off Off on off off
27 on on off on on off off off 37 on off on off Off on off off
28 off off on on on off off off 38 off on on off Off on off off
29 on off on on on off off off 39 on on on off Off on off off
30 off on on on on off off off 40 off off off on Off on off off

Speed Dome Camera Instruction Manual 10
1234
ON
O
N
Terminal Resistor Setup
1234
ON
ON
zPin 3 is only for supplier, UDO NOT CHANGE THESE ITS ORIGINAL
STATEU.If you change one of these, proper operation can not be
achieved.
~Pin 3 PAL / NTSC system selection of Camera. UDO NOT
CHANGE THIS PINU.
INSTALLATION
2
T
erminal resistor is used if your system meets one of following two
c
onditional cases.
zCase1: Control cable between camera and controller is
relatively long (1:1 connection)
If communication cable is very long, the electrical signal will bind in
the terminal point. This reflected signal causes signal distortion,
resulting in a degradation of camera function. In this case, the
terminal resistor of both sides (i.e. camera and controller) must be
set to the ‘ON’ state.
zCase2: Multiple cameras are controlled at the same time
Due to similar reasons stated in case 1, the terminal resisters of the
controller and the last camera must be set to ‘ON’ state. The
camera with the longest cable length is determined to be the ‘last’
camera. Do not turn on the terminal resistor of all cameras.

Speed Dome Camera Instruction Manual 11
Installation using Ceiling Mount Bracket
After putting the Gasket on the ceiling
Fasten ceiling mount bracket to ceiling with 3
screws.
②Wire cables to terminals and connect the
terminals to main unit. Do not use surface mount
bracket!
① Hang the camera on the safety ring and
assemble it using the fall-proof spring.
② Remove protective vinyl from dome cover.
INSTALLATIONINSTALLATION 2 INSTALLATION

Speed Dome Camera Instruction Manual 12
Installation using Wall Mount Bracket
①After putting the Gasket on the wall
Fasten wall mount bracket to ceiling with 4
screws.
②Wire cables to terminals and connect the
terminals to main unit. Do not use surface
mount bracket!
③ Fasten main unit to wall mount bracket with 4
screws.
④ Remove protective vinyl from dome cover.
2
INSTALLATION

Speed Dome Camera Instruction Manual 13
Installation using Flush Mount Bracket
.
2
③ Connect fall-proof spring to main body
hook. Assemble and fasten with screws.
Cut 3 holes in ceiling ② Align main body bracket with flush mount
bracket. Fasten with screws.
④ Put main body and bracket assembly into
main hole.
⑥ Cover assembly with bracket
cover and turn it clockwise.
⑤ Secure flush mount bracket to the ceiling
with screws through the 3 holes on the
bracket.
INSTALLATION

Speed Dome Camera Instruction Manual 14
Cabling
Power
IN COM+
IN1
IN2
IN3
IN4
PWR(+)
PWR(-)
F.G
RS-485(+)
RS-485(-)
Cabling Terminal Block
VIDEO(+)
VIDEO(-)
Controller/ DVR
Moinitor
BNC Sensor
IrDA
Sensor
Door
Switch
Power Connection
zPlease check the voltage and current capacity of rated power carefully. Rated power is indicated on the
back of main unit.
Rated Power Input Voltage Range Current Consumption
AC 24V (PT112N) AC 17V ~ 29V 0.4 A
AC 24V (PT112N-XT) AC 17V ~ 29V 1.5 A
zDC power loss increases over distance. DC power wiring to cameras should be kept as short as possible.
RS-485 Communication
zFor PTZ control, connect the RS-485 line to keyboard and DVR. To control multiple cameras on the same line
with simultaneous operation (see page 13 for resistor settings): the RS-485 communication lines to cameras
are connected in parallel as shown below.
2
INSTALLATION

Speed Dome Camera Instruction Manual 15
Video Connection
zConnect with BNC coaxial cable.
Alarm Input Connection
zSensor Input
Before connecting sensors, check the sensor driver voltage and output signal type. Since sensor output
signal types are divided into Open Collector and Voltage Output types in general, the cabling must be
installed properly depending on the signal type.
Signal Description
IN COM (GND) Connect SENSOR COMs to this port(GND) as shown in the circuit above.
IN1, IN2, IN3, IN4 Connect output of sensors for each port as shown in the circuit above.
INSTALLATION 2
Internal
SENSOR COM
(GND)
SENSOR IN1
SENSOR COM
(GND)
SENSOR IN2
SENSOR COM
(GND)
SENSOR IN3
SENSOR COM
(GND)
SENSOR IN4

Speed Dome Camera Instruction Manual 16
If you want to use Alarm Input, the type of sensor must be selected in OSD menu. The sensor types are
Normal Open and Normal Close. If the sensor type is not selected properly, alarm activation will occur
opposite of what is desired.
~Normal Open Output Voltage is high state when sensor is activated
~Normal Close Output Voltage is high state when sensor is not activated
INSTALLATION
2

Speed Dome Camera Instruction Manual 17
Check Points before Operation
zBefore power is applied, please check the cables carefully.
zThe camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by
reading DIP switch of the camera.
zIf your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
zIf you changed camera protocol by changing DIP switch, the change will be effective after you reboot the
camera.
zSince the operation method can be different for each controller available, refer to the manual for your controller
if camera can not be controlled properly. The operation of this manual is based on the standard Pelco®
Controller.
Preset and Pattern Function Pre-Check
zCheck controller or DVR preset and pattern functions in advance when using controller or DVR.
zRefer to the following table when using standard Pelco® protocol controller.
< Go Preset > Input [Preset Number] and press [Preset] button.
< Set Preset > Input [Preset Number] and press [Preset] button for more than 2 seconds.
< Run Pattern > Input [Pattern Number] and press [Pattern] button.
< Set Pattern > Input [Pattern Number] and press [Pattern] button for more than 2 seconds.
zIf controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more
information, refer to “Reserved Preset” in this manual.
OPERATION 3

Speed Dome Camera Instruction Manual 18
Starting OSD Menu
zFunction Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be
configured for each application
zEnter Menu <Go Preset> [95]
Reserved Preset
zDescription Some Preset numbers are reserved to special functions.
zFunction Go Preset [95] : Enters into OSD menu
Go Preset [131~134] : Runs Pattern Function 1 ~ 4
Go Preset [141~148] : Runs Swing Function 1 ~ 8
Go Preset [151~158] : Runs Group Function 1 ~ 8
Go Preset [170] : Sets Camera BLC Mode to OFF
Go Preset [171] : Sets Camera BLC Mode to ON
Go Preset [174] : Sets Camera Focus Mode to AUTO
Go Preset [175] : Sets Camera Focus Mode to Manual
Go Preset [176] : Sets Camera Focus Mode to SEMI-AUTO
Go Preset [177] : Sets Day & Night Mode to AUTO
Go Preset [178] : Sets Day & Night Mode to NIGHT
Go Preset [179]
Go Preset [182]
Go Preset [183]
: Sets Day & Night Mode to DAY
:Sets Camera IRIS mode to AUTO
:Sets Camera IRIS mode to Manual
Go Preset [190] : Sets OSD Display Mode to AUTO (Except Privacy Mask)
Go Preset [191] : Sets OSD Display Mode to OFF (Except Privacy Mask)
Go Preset [192] : Setting OSD Display Mode to ON (Except Privacy Mask)
Go Preset [193] : Sets all Privacy Mask Display to OFF
Go Preset [194] : Sets all Privacy Mask Display to ON
OPERATION 3

Speed Dome Camera Instruction Manual 19
Preset
zFunction Max. 127 positions can be stored as Preset position. The Preset number can be
assigned from 1 to 128, but 95 is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up
independently for each preset. Label should be blank and "Camera Adjust" should be
set to "GLOBAL" as default. All characteristics can be set up in OSD menu.
zSet Preset <Set Preset> [1~128]
zRun Preset <Go Preset> [1~128]
zDelete Preset To delete Preset, use OSD menu.
Swing
zFunction By using Swing function, the camera can move between 2 Preset positions repeatedly.
When swing function runs, camera moves from the preset assigned as the 1st point to
the preset assigned as the 2nd point in CW (Clockwise) direction. Then camera moves
from the preset assigned as the 2nd point to the preset assigned as the 1st point in
CCW (Counterclockwise) direction.
If the preset assigned as the 1st point is the same as the preset assigned as the 2nd
point, the camera will turn 360°in a CW (Clockwise) direction, then 360°in a CCW
(Counterclockwise) direction.
Speed can be set up from 1°/sec to 180°/sec.
zSet Swing To set Swing, use OSD menu.
zRun Swing Method 1) <Run Pattern> [Swing NO.+10]
Method 2) <Go Preset> [Swing NO.+140]
ex) Run Swing 3 : <Run Pattern> [13]
ex) Run Swing 3 : <Go Preset> [143]
zDelete Swing To delete Swing, use OSD menu.
OPERATION
3
1st Preset
2nd Preset
1CWDirection
2CCWDirection

Speed Dome Camera Instruction Manual 20
Pattern
zFunction Pattern Function allows the camera to memorize a path (often a curved path) created
by controller joystick for an assigned time. The camera will then retrace the path
exactly as memorized.
4 Patterns are available and Maximum 1200 communication commands can be stored
in a pattern.
zSet Pattern Patterns can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.]
{Pattern editing screen is displayed as bellow.
EDIT PATTERN 1
[NEAR:SAVE /FAR:DELETE]
0/0/x1/N
{Movement by Joystick and preset movement can be memorized in a pattern.
{The remaining memory size is displayed in progress bar.
{To save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu: See the section “How to use OSD Menu”.
zRun Pattern Method 1) <Run Pattern> [Pattern NO.]
Method 2) <Go Preset> [Pattern NO.+130]
ex) Run Pattern 2 : <Run Pattern> [2]
ex) Run Pattern 2: <Go Preset> [132]
zDelete Pattern Use OSD menu to delete a Pattern.
OPERATION 3