CBC AFZC-22X User manual

A
F Zoom Camera
AFZC-22X


EG-2
This symbol indicates that there is a possibility of death or damage to operator or others.
To prevent fire or electric shock, do not expose this product to rain or moisture.
CAUTIONS
This symbol indicates that there is a possibility of injury or damage to equipment.
WARNING
Thank you for your purchase of this product. Before operating the product, please read this
instruction manual carefully to ensure proper use of the product. Please store this instruction
manual in a safe place for future reference.
CONTENTS
SAFETY PRECAUTIONS .................................................................................................. EG-2
REAR PANEL ................................................................................................................. EG-4
REMOTE CONTROL ........................................................................................................ EG-4
OSD OPERATION ........................................................................................................... EG-5
SPECIFICATIONS ......................................................................................................... EG-12
SAFETY PRECAUTIONS
The installation should be made by qualified service personnel or system installers and should
conform to all local codes.

1. Power supply
(1) Use only with a 24V AC power supply marked class 2 or +12V DC regulated power supply
marked class 2.
(2) To prevent fire or electrical shock, UL listed class 2 wiring should be used for the 12VDC or
24VAC input terminal.
(3) Be sure to connect each lead to the appropriate terminal. Wrong connection may cause
malfunction and/or damage to the video camera.
2. Operating and storage locations
(1) Do not attempt to aim the camera at the sun or other extremely bright objects that cause
smear to appear irrespective of whether the camera is operating or not. This can damage
the CCD(Charge Coupled Device).
(2) Do not place the camera in the following locations.
a) Locations subjected to extremely high or low temperatures.
(operating temperature range : -10°C to +50°C {14°F to 122°F})
(storage temperature range : -20°C to +60°C {-4°F to 140°F})
b) Locations subjected to high levels of humidity and dust.
(operating humidity range:max 85% {no condensation})
(storage humidity range : max 85% {no condensation})
c) Locations where there are large amounts of water vapour and steam
d) Ensure the location selected is sufficiently strong enough to support the weight of the camera
and is free from vibration.
(3) When this camera is installed near equipment, like a wireless communication device, that
emits a strong electromagnetic field, some irregularity such as noise on the monitor screen
may happen.
(4) Be sure to use screws suitable for the type of material to which the camera is being mounted.
3. Handling of the unit
Do not allow the camera to be subjected to strong impacts or shocks. The camera could be
damaged by improper handling or storage.
- Never attempt to disassemble or modify the camera.
- If an abnormality should occur, immediately turn off the power and consult your dealer.
The CE Marking is a Directive Conformity mark of the European Union (EU).
EG-3

CANCEL
AF
AWB
INT
PHASE
UP
MENUENTER
S-VIDEO
DOWN
LL
VIDEO
AC 24V
DC 12V
- + REMOTE/RS232C
Menu button: Displays and erases Menu Screen.
Up button: Move the cursor up.
Down button: Move the cursor down.
Enter button: Select the mode.
Cancel button: Exit to Main Menu.
BNC connector:
Composite Video output
S-Video: Y/C output
Power: 12VDC or 24VAC
AF button: One-push AF
Int./L.L.:
Internal Sync mode/Line Lock
mode switchable.
Remote Control:
D-sub 9 pin controls RS-232C and
Lens Direct Control from standard lens
controller.
Phase Adjustment:
Line Lock phase adjustment.
AWB:
One-push White balance
EG-4
D-sub 9 pin:Pin No.1: not used.
No.2: RD (RS-232C)
No.3: SD (RS-232C)
No.4: not used
No.5: Ground (RS-232C)
No.6: Ground for Lens Control
No.7: Iris (+Close)
No.8: Focus (+Near)
No.9: Zoom (+Tele)
a) Lens Control: Pin No.6/7/8/9
Min. 2V / Max. 12V
Absolute Max. Regulated Voltage: 16V DC
6
7
98
1
2
543
REAR PANEL
REMOTE CONTROL
±
±±

b) RS-232C Interface: Pin No.2/3/5
Communication Method: Full Duplex
Communication Rate: 9600bps
Transmission Method: bit serial (binary data)
8 bit fixed
start bit=1, stop bit=1
No parity bit
OSD (On Screen Display) Operation
1) Menu button:
Push Menu button, and following screen will apear.
EG-5
Blinking title is your choice at
present. The blinking item
goes up and down by pushing
"UP"/"DOWN" buttons. After
selecting the title, push "Enter"
to set.
After you finish your settings,
push "Menu" button to exit.
Push "Cancel" button to go
back to Main Menu while
adjusting.
2) PRESET:
You can set 64 different Zoom/Focus positions.
How to preset:
a) First, obtain the desired picture by using "ZOOM" and/or "FOCUS".
b) Then, go back to "Main Menu", and select "PRESET".
c) Push "Enter" twice and select "Position" 1 through 64, and push "Enter".
d) Move the cursor down to "SET" and push "Enter".
e) Repeat a) to d) to set Max. 64 positions.
f) to operate the Preset position:
f-1) Select "PRESET", and push "Enter" twice.
f-2) Select Position (1 through 64) by "UP" or "DOWN" button, and push "Enter".
f-3) Move the cursor down to "RECALL" and push "Enter".
f-4) Repeat f-1) to f-3) to choose other positions.
Communication protocol: start/stop system,
original process
Error Recovery: No error detection,
Re-transmission
by PC
Flow Control: No

3) ZOOM:
a) Select "ZOOM" in Main Menu by pushing "Enter" button.
b) Select "Tele/Wide" by pushing "Enter" button.
c) Move the cursor down to "TELE", and push "Enter" twice to zoom in.
Push "Enter" again to stop zooming in.
d) When you would like to zoom out, push "Enter" once, and then push "UP" button.
Then, you switch to "WIDE". Push "Enter" to zoom out and push "Enter" again to stop
zooming out.
Electronic Zoom: a) Select "ZOOM" in Main Menu, and push "Enter".
b) Push "Enter" again. Then, "E. ZOOM" is blinking.
c) Push "Enter", and then select "off, 4X, or 8X" by pushing "UP" or
"DOWN" button. Then, push "Enter" to set.
Zoom Speed: a) Select "ZOOM" in Main Menu, and push "Enter".
b) Push "Enter", and move the cursor down to "SPEED".
c) Push "Enter", and select Speed between "0" (slowest) to "7" (fastest)
by pushing "UP" or "DOWN" button.
d) Push "Enter" to set.
EG-6
POSITION : 1 through 64
RECALL: move to preset postion.
SET: record the position.
RESET: back to factory setting.
RESET ALL:put all positions back to factory settings.
g) to Reset the particular Preset position back to factory setting.
g-1)Select "PRESET", and push "Enter" twice.
g-2)Select particular Preset Position (1 through 64) by "UP" or "DOWN" button, and
push "Enter".
g-3)Move the cursor down to "RESET" and push "Enter".
g-4)Repeat g-1) to g-3) to reset other positions.
h) to Reset all the positions (64 positions) back to factory settings.
h-1)Select "PRESET", and push "Enter" once.
h-2)Move the cursor down to "RESET ALL", and push "Enter".

EG-7

TELE/WIDE: setting by TELE/WIDE
DIRECT: setting by input the number
E.ZOOM: Digital Zoom ON (x 4, x 8) / OFF setup
SPEED: speed of TELE/WIDE setup
TELE/WIDE: TELE/WIDE setup
POSITION: input a hexadecimal number (on DIRECT)
4) FOCUS:
a) Select "FOCUS" in Main Menu by pushing "Enter" button.
b) Select "AF, FAR/NEAR, DIRECT, ONE-PUSH, INFINITY".
AF mode: a)Push "Enter", and select "SENSE(AF Sensitivity)" to High or Low by "UP"
(Auto Focus) or "DOWN" button, and push "Enter" to set.
FAR/NEAR: a)Select "FAR/NEAR" by pushing "Enter" button.
b)Push "Enter" again and move the cursor down to "FAR".
c)Push "Enter" again. Then, "FAR" is blinking, and select "FAR" or "NEAR"
by pushing "UP" or "DOWN" button.
d)Push "Enter" to start Focus movement, and push "Enter" again to stop.
Focus Speed: a)Select "FAR/NEAR" by pushing "Enter" button, and "SPEED" is blinking.
b)Push "Enter", and select Speed between "0" (slowest) to "7"(fastest) by
pushing "UP" or "DOWN" button.
c)Push "Enter" to set.
DIRECT: a)Select "DIRECT".
b)You can set the focus position by Hexadecimal number.
ONE-PUSH: One-Push AF button.
INFINITY: Set to "Infinity" focus."
SENSE: Select Sensitivity between HIGH/LOW. This can be controlled only during
AF mode.
AF: Auto Focus
FAR/NEAR: setting by FAR/NEAR
DIRECT: setting by input a numerical number
ONE-PUSH: one-push Auto Focus
INFINITY: forced infinity
SPEED: speed of FAR/NEAR
SENSE: sensitivity of Auto Focus
FAR/NEAR: FAR/NEAR setting
POSITION: input a hexadecimal number (on DIRECT)

5) WHITE BALANCE:
Select from:AUTO: 3200-6000K
INDOOR: 3200K
OUTDOOR: 5800K
AWB: one-push AWB
ATW: 2000-10000K
MANUAL: R/B setting
and push "Enter" to set.
MANUAL: a) Push "Enter" button.
b) Adjust "R" & "B" by "UP" or "DOWN" button.
6) AE:
Select from:FULL AUTO
MANUAL
SHUTTER:Shutter Priority
IRIS: Iris Priority
GAIN: Gain Priority
Slow Shutter Mode: This is frame integration mode, which is suitable for getting bright picture in
darkness. But this is not suitable for fast moving object.
a) Select "FULL AUTO" mode, and push "Enter".
b) Select "Slow : off" or "Slow : on" by "UP" or "DOWN" button.
c) Push "Enter" to set.
When you select the mode other than AE, please select desirable level for SHUTTER/ IRIS/GAIN
by pushing "UP" or "DOWN" button.


Choose which white
balance is used.
R/B gain setting
(on MANUAL)
Mode Iris Gain Shutter
FULL AUTO Auto Auto fixed (1/50 or 1/60)
MANUAL 18 steps 8 steps 20 steps
SHUTTER Auto Auto 20 steps
IRIS 18 steps Auto Auto
GAIN Auto 8 steps fixed (1/50 or 1/60)
BRIGHT 24 combinations of Iris/Gain. fixed
SHUTTER AUTO 18 steps 8 steps Auto
IRIS AUTO Auto 8 steps 20 steps
GAIN AUTO 18 steps Auto 20 steps
Please refer as follows how each mode operates:
EG-8
BRIGHT
SHUTTER AUTO
IRIS AUTO
GAIN AUTO

Bright combination of IRIS
and GAIN
Step IRIS Gain
1CLOSE 0dB
2F22
3F19
4F16
5F14
6F11
7F9.6
8F8
9F6.8
10 F5.6
11 F4.8
12 F4
13 F3.4
14 F2.8
15 F2.4
16 F2
17 F1.6
18 OPEN 0dB
19 3dB
20 6dB
21 9dB
22 12dB
23 15dB
24 OPEN 18dB
EG-9
Please refer to the following table regarding the 2 digit data for
IRIS/SHUTTER/GAIN/BRIGHT/EXP.COMP.
IRIS
Step Data IRIS
100 CLOSE
201 F22
302 F19
403 F16
504 F14
605 F11
706 F9.6
807 F8
908 F6.8
10 09 F5.6
11 0A F4.8
12 0B F4
13 0C F3.4
14 0D F2.8
15 0E F2.4
16 0F F2
17 10 F1.6
18 11 OPEN
Shutter
Step Data Shutter
100 1/4
201 1/8
302 1/15
403 1/30
504 1/60
605 1/90
706 1/100
807 1/125
908 1/180
10 09 1/250
11 0A 1/350
12 0B 1/500
13 0C 1/725
14 0D 1/1000
15 0E 1/1500
16 0F 1/2000
17 10 1/3000
18 11 1/4000
19 12 1/5000
20 13 1/10000
Gain
Step Data Gain
100 -3dB
201 0dB
302 3dB
403 6dB
504 9dB
605 12dB
706 15dB
807 18dB
Exp.Comp.
Step Gain
1-10.5dB
2-9dB
3-7.5dB
4-6dB
5-4.5dB
6-3dB
7-1.5dB
80dB
91.5dB
10 3dB
11 4.5dB
12 6dB
13 7.5dB
14 9dB
15 10.5dB

EG-10

→ＯＮ



7) EXP.COMP.:
To set up AGC level.
a) Select "EXPCOMP" and push "Enter".
b) Select "ON".
c) Adjust the level by "UP" or "DOWN"
button.
d) Push "Enter" to set.
8) BACK LIGHT:
To select "Back Light Compensation" On or OFF.
a) Select "BACK LIGHT" and push "Enter".
b) Select "ON" or "OFF" by "UP" or "DOWN"
button.
c) Push "Enter" to set.
9) ENHANCER:
To select the level of Edge Enhancement
(soft or sharp).
a) Select "ENHANCER" and push "Enter".
b) Adjust to Soft or Sharp by "UP" or
"DOWN" button.
c) Push "Enter" to set.
10) CHROMA:
To select "Chroma gain" level.
a) Select "CHROMA" and push "Enter".
b) Adjust "Chroma gain" by "UP" or
"DOWN" button.
c) Push "Enter" to set.
Gain setup (on Manual)

EG-11


11) FREEZE:
To freeze the picture.
a) Select "FREEZE" and push "Enter".
b) Choose "ON".
c) Choose "OFF" to go back to Live Mode.
12) DATE/TIME:
To set the date and time.
a) Select "DATE/TIME" and push "Enter".
b) Choose "ON".
c) Set the date/time by "Enter" button, and
"UP"/ "DOWN" buttons.
d) Push "Enter" to set.
e) Choose "OFF" to delete OSD.
13) TITLE:
To set the title.
a) Select "TITLE" and push "Enter".
b) Choose "ON".
c) Set the title by "Enter" button, and "UP"/
"DOWN" buttons.
d) Push "Enter" to set.
e) Choose "OFF" to delete OSD.
14) ID:
This camera ID can be set only through
RS232C, and it cannot be set by Menu Screen.
Still image setting

Model AFZC-22X / NTSC AFZC-22X / PAL
TV System NTSC PAL
Image Sensor 1/4” CCD ICX - 228AK 1/4” CCD ICX - 229AK
Effective number of pixels 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2:1 Interlace
Scanning Frequency 15.734 kHz(H) 59.94 Hz(V) 15.625 kHz(H) 50.0 Hz(V)
Sync.System Int / Line-lock switchable
Horizontal Resolution 460 TV lines
Video Output 1.0 V(p-p) / 75 ohm. Video 0.714 V(p-p), Sync.0.286 V(p-p)
Burst Signal 0.286 V(p-p)
Y/C output Y : 1.0 V(p-p) ( 0.2 V(p-p) ) C : 0.3 V(p-p) ( 0.05 V(p-p) )
S/N ratio More than 46dB (Gamma=1, AGC off, Aperture off)
Min.Illumination 2.5 lx (F1.6 50IRE) 3 lx (F1.6 50IRE)
Gamma 0.45
AGC Auto / Manual (Max.18 dB)
ALC Galvanometer lens, Auto / Fix
AES Auto / Manual
1 / 4-1 / 10,000 fix. 1 / 3-1 / 10,000 fix.
BLC On / Off
White Balance ATW / AWB / Fix / Manual
Zoom Optical : 22X (3.9mm - 85.4mm), Digital : On (4X,8X) / Off
Focus Auto / Manual
Preset Focus : 64 positions, Zoom : 64 positions
Remote Control RS232C DC direct control (2V - 12V )
OSD Camera ID (20 characters) Menu setting
Operating Temperature& Humidity -10 to + 50 degrees C, 85 % RH Max. (No Condensation)
Storage Temperature & Humidity -20 to + 60 degrees C, 85 % RH Max. (No Condensation)
Power Input 12V DC / 24V AC Auto switching
Power Consumption 12V DC / 310mA typ. 24V AC / 120mA typ.
External Dimensions 62(W) x 75(H) x 141.3(D)mm
Weight 460g
SPECIFICATIONS
Printed in JAPAN
±±