CBS AVS-010-INST - C User manual

AVS-010-INST - C AUG 2013

CBS VCALL SYSTEM
INCLUDED COMPONENTS
Single Screen Mount Dual Screen Mount
Column
Codec
Bracket
Camera
Mount
End Caps
Spare
Fixings
2 x Velcro Fasteners
6 x Buttons
Shelf
(Optional)
x1 x1 x4
AVS/010/K01 AVS/010/K02
x4 x4 x2
Screen
Mount x1
Extension
Brackets x2
Screen
Mount x2
Extension
Brackets x4
Allen Keys x2 Screen
Mounts x2

BALANCE
LEVEL
SOME IMPORTANT PRECAUTIONS

SOME IMPORTANT PRECAUTIONS
INTERNAL
EQUIPMENT
S P A C E
WARNING
ELECTRICAL SAFETY
• Total weight of installed equipment must not exceed 120kg/264lb, symmetrically distributed.
• Use with products heavier than the maximum weights indicated may result in instability causing possible injury.
• Correct installation is essential to safe and reliable operation of the VCALL product and falls outside the scope of responsibility
of Colebrook Bosson Saunders. Please follow assembly instructions carefully.
• Do not use this product for any purpose other than that for which it was designed.
• Ensure that oor or wall surface is strong enough to support the weight of the fully-loaded VCALL and that the oor surface is at and level.
• Do not install VCALL outdoors or in environments where it will be directly exposed to moisture or highwinds.
• Follow the manufacturer’s guidance for mounting of monitors, displays and other equipment.
• Please take care to avoid trapping ngers when installing or adjusting the product.
• Safe installation of electrical equipment is the responsibility of the installer.
• Colebrook Bosson Saunders recommends that only double-insulated electrical equipment and cables are installed in VCALL unit.
MAINTENANCE AND INSPECTION
• Ensure all screws and xings are fully tightened and occasionally re-tighten if necessary.
• Clean with a dampcloth. DO NOT use solvents.

INSTALL SCREEN MOUNT BEAM BRACKETS
1
INSTALL THE SINGLE SCREEN MOUNT
2INSTALL THE D U A L SCREEN MOUNT 3
i
i
iii Insert End Caps
vInsert End Caps
Fit M5 screws to
Dual screen mounting
frame as shown
Fit screen mounting
frame to beam brackets
Fit screen
mounting frame
to beam brackets
i i
i v
iii Align using centre-
line mark
i i
Fit 8 x M5 screws
and tighten
Fit 8 x M5 screws
and tighten
Unless panel needs to be
removed, leave zip tie in
place during installation

R E M O V E T H E B A C K P A N E L
4
INSTALL THE CAMERA MOUNT ARM
6INSTALL THE CAMERA MOUNT PLATFORM 7
INSTALL CODEC MOUNT
5

A T T A C H S C R E E N
MOUNT BRACKETS
9HANG SCREEN DIRECTLY ONTO MOUNTING FRAME 1 0
INSTALL COMPLETED CAMERA MOUNT ASSEMBLY BY PLACING ON THE SCREEN MOUNT
8
3
Per screen
x4 x4
2 people required
to mount screens

FINE HEIGHT ADJUSTMENT (DUAL ONLY) FOR SCREEN APPLICATION
1 1
SECURE SCREEN BRACKETS IN PLACE
1 2
Clockwise to adjust downwards from bracket
Anti-Clockwise to adjust upwards from bracket
If screens are not aligned
vertically, adjust as required
with 4mm Allen key

CABLE MANAGEMENT
1 3
Due to the range of different
technology solutions the Cable
Management is optional. The CBS
VCALL provides several solutions
that can be used to suit your needs.
Feed cables out through
the front of the unit
1 A
Cut velcro wraps to
required length
3 A
Release channel
2 A
Pass cable through
holes in base
4 A
Feed cables
through channel
Ensure channel locates
2 B
2 C
Use velcro wraps to
attach to crossbar
3 B
Use velcro to stick wraps
to side of columns
3 C
Pull cables clear
of the base
4 B
Clip cables into management
clip underneath base to secure
4 C
click

C L O S E T H E B A C K P A N E L
1 4
INSTALLATION COMPLETE