ccei Mini Brio M12 User manual

Technical Manual
Mini Brio M12
(&12K, 12B) & 12HW
Underwater LED lighting
Réf : PK10R300 / PK10R301 / PK10R302 /
PK10R308 / PK10R309 / PK10R310
Table of Contents
1. Technical characteristics .................................................................................................................. 1
2. Packaging Contents ........................................................................................................................ 2
3. Installation ................................................................................................................................... 2
3.1. Installation in the wall conduit ................................................................................................ 2
3.2. Electrical connection ............................................................................................................ 2
4. Cable Cross-Section ....................................................................................................................... 3
5. Projector Protection ........................................................................................................................ 3
A. Declaration of conformity .............................................................................................................. 3
Read these instructions carefully before installing, commissioning and using this product
Floodlights must never be turned on outside of water
Always use safety transformer only
1. Technical characteristics
Dimensions Ø 47 mm / length 84mm
Installation In 1.5" or 2" vacuum point
In 2" threaded or 63mm smooth wall passage with optional PF10R25A adapter
Power supply Voltage: 12 V~ AC / Frequency: 50Hz/60Hz
Consumed power 14W (M12 version)
8W (HW version)
LED type
3 monochrome power LEDs
PK10R300 (M12) &
PK10R308 (M12 HW) Cool White (~6000°K)
PK10R301 (M12K) &
PK10R309 (M12K HW) Warm White (~3000°K)
PK10R302 (M12B) &
PK10R310 (M12B HW) Blue
Risk group 1 (low risk) according to IEC62471:2006
IP Rating IP-68
Max light stream 866 lm max. (M12, M12K & M12B)
400 lm max. (M12 HW)
MPNT0258 v2.0ML (02/05/2018)

Technical Manual Mini Brio M12 (&12K, 12B) & 12HW v2.0ML
2. Packaging Contents
1 BRIO light Mini Brio M with
• 2x0.75mm² cable: 3m (pre-assembled)
• Technical manual (this document)
3. Installation
To ensure good fixing the engraved arrow under the patch (at the glue side) should point inside the pool
3.1. Installation in the wall conduit
A. Bend of the back of the non-watertight wall conduit (refer
to the installation of the wall conduit)
B. Raise the cable above the water line (here in a connection
box)
Threaded wall conduit 1.5''
1. Pass the cable through the wall con-
duit
2. Push and screw it thoroughly
Threaded wall conduit 2''
1. Screw the cable into the adaptor and
pass the cable through the wall con-
duit
2. Push and screw it thoroughly
Non-threaded wall conduit 2''
1. Place the o-ring provided with the
adaptor
2. Pass the light cable through the wall
conduit
3. Push the light to the stop
3.2. Electrical connection
Installation of this product involves a hazard of electric shocks. We strongly recommend you
contract a professional installer. Incorrect installation places you in danger and may irre-
versibly damage the product and the equipment connected to it. In compliance with the NF C
15-100 standard, pool lights installed in Volume 0 must always be powered with SELV (Safety
Extra Low Voltage). Always cut off the power upstream before handling the electrical instal-
lation.
Risk of electric shock. Only connect to a circuit which is protected by a ground-fault circuit
interrupter. If you are not sure if these types of devices are fitted, contact a qualified electrician.
2

Technical Manual Mini Brio M12 (&12K, 12B) & 12HW v2.0ML
The electrical connection must be performed dry, in a sealed
connection box whose cable glands must be tightened in order
to avoid any water infiltration.
4. Cable Cross-Section
CROSS-SECTION (mm²)
1,5 2,5 4 6
The voltage drop in the supply cable of the
Mini Brio M12 (&12K, 12B) & 12HW ca-
ble should be limited in order to comply
with the applicable standards and ensure
optimal illumination.
Follow the table opposite (one projector
per cable);
Max. length
(m) 16 (M12) 26.7 (M12) 42.7 (M12) 64 (M12)
5. Projector Protection
IndependentprotectionisnecessaryforeachMiniBrioM12(&12K,12B)&12HW.Protectionmustbeensuredinthesecondary
of the transformer using fuses or breakers at 2A or 3A.
A. Declaration of conformity
Bleu Electrique SAS (FR47403521693) declares that product Mini Brio M12 (&12K, 12B) & 12HW is com-
pliant with the safety and electromagnetic compatibility requirements of European directives E.M.C (2014/30/
UE), Low voltage (2014/35/UE), RoHS (2011/65/UE), WEEE (2002/96/CE) and REACH (1907/2006).
Emmanuel Baret
Marseilles, on 02/05/2018
Distributor's stamp
Date of sale: . . . . . . . . . . . . . . . . . . . . . . . Batch N°: . . . . . . . . . . . . . . . . . . . . . . . . . . .
3