CCTVMATE.COM LCD330 User manual

LCD330 Instruction Book 
PTZ Control Testing
RS485 Data Test
Function
Monitor Output
Testing
Built-in Multimeter
Video Signal Meter
Network Cable
Tester
Up To 10 Hour
Battery Life
Essential CCTV Camera Test Monitor
The feature packed LCD330 CCTV test monitor kit comes with voltage probes for use with
the built-in multimeter, an RS485 data test cable, a 12V DC power cable so that cameras can
be powered by the test monitor during conguration, a short BNC cable for connecting test
monitor to cameras or monitors, sturdy nylon carry case with optional shoulder strap, neck
strap, PSU for charging the LCD330 and a network cable tester.
LCD330

LCD330 Instruction Book
2
Safety Information
Precautions Before Using The LCD330
1. Read and understand the User Manual before using
this product.
2. Ensure the CCTV test monitor is used within each
specied range to avoid damaging the unit.
3. The LCD330 should only be used under the following
conditions:
A. Temperature: -30° ~ 70°
B. Relative humidity: 30% ~ 90%
C. Recharging voltage: 9V DC 2.0A
Precautions When Using The LCD330
1. Do not use the test monitor in damp, humid or leaking
gas environments.
2. Do not touch the LCD330 with moist or wet hands.
3. Measurements may be incorrect when the CCTV test
monitor is used in places subjected to strong magnetic
elds or electromagnetic waves.
4. Be careful not to expose the ports or joints to dirt
or liquid.
5. Do not disassemble the CCTV test monitor. If the unit
requires any repairs return the unit to the retail outlet you
purchased it from. Attempting to repair the unit yourself
will void the warranty.
6. Do not connect this unit to other Input/Output devices
when using the multimeter function.
Precautions When Charging The Battery
1. Only ever use the original battery supplied with the test
monitor, when charging the battery you should only use
the original power adapter provided.
2. Do not short-circuit or disassemble the battery.
3. Do not use the multimeter function when charging
the battery.
Contents
Safety Information 2
Getting Started 3
Connections & Controls 3
Kit Contents 5
Functions & Features 5
Battery & Power 6
Main Menu 6
System Information 7
Video Testing 8
PTZ Testing & Control 9
Video Signal Analysis 10
UTP (Network) Cable Testing 11
Video Generator 12
RS485 Data Testing 13
Digital Multimeter 14
12V DC Power Output 15
Specication & Warranty 16

LCD330 Instruction Book
3
Getting Started
Before taking the CCTVmate out on its rst job, please ensure that the unit is fully charged by using the charger supplied. For
more information on charging the device see the‘ Battery & Power ’ section on page 6.
Connections & Controls
Front
Charging Indicator
Solid light when charging,
ashing when fully charged.
Open Iris & Select
Open Iris in PTZ control
mode or ‘ Conrm ’ current
selection or input.
Close Iris & Exit
Close Iris in PTZ control
mode or ‘ Cancel ’ current
selection or input.
3” LCD Screen
960 x 240 Resolution.
Menu
Long press returns to main
menu. Quick press displays
and hides sub menu.
Direction Buttons
Move PTZ and select menu
options.
Address
Input the address of the
PTZ you wish to control.
Set Preset
Set preset in PTZ control
mode.
Call Preset
Call preset in PTZ control
mode.
Near
Adjusts PTZ to focus on
near by objects.
Far
Adjusts PTZ to focus on far
away objects.
Wide
Zoom out PTZ or close
video test signal.
Tele
Zoom in PTZ or start video
test signal.
0 - 9
Input menu or preset number.
Power Indicator
Solid light when the test
monitor is on.
Transmitting Indicator
Flashes when data is being
transmitted.
Receiving Indicator
Flashes when data is being
received.

LCD330 Instruction Book
4
Side 1
Power On / Off
Power switch.
Power Input
9V DC jack input.
UTP (RJ45) Socket
UTP socket for network
cable testing.
Side 2
Top Bottom
Video Output
BNC connection for video
output to monitor.
Video Input
BNC connection for video
input from the camera.
RS485 / RS422 Port
For testing, conguration
and control.
+ Probe Connection
Connection for ‘ Positive ’ probe
when using the multimeter.
- Probe Connection
Connection for ‘ Ground ’ probe
when using the multimeter.
RS232 Port
For conguration and
operation via RS232.
12V DC Output
For powering 12V DC cameras
when testing.
Fold-out Stand
Optional fold-away stand.

LCD330 Instruction Book
5
Kit Contents
The LCD330 is supplied with all the cables and tools needed
for testing the key aspects of a CCTV installation.
Neck Strap
For practicality and
security whilst up a ladder.
Voltage Probes
Allows the test monitor to
be used as a multimeter.
RS485 Data Test Cable
For connecting RS485 &
RS422 wires to the LCD330.
12V DC Power Cable
For powering cameras with
the LCD330 test monitor.
BNC Cable
Used connect the LCD330
to camera, DVR or monitor.
9V DC PSU
For charging the LCD330
test monitor.
Network Cable Tester
Used to detect faults in
UTP network cables.
Carry Case
Sturdy nylon carry case with
optional shoulder strap.
Functions & Features
The LCD330 is one of the most comprehensive CCTV test
monitors on the market. This feature packed device is a must
have for any CCTV installer oering all the functions you
would only expect to nd on higher priced models.
Video Testing
Displays the camera’s image so that adjustments can be
made during installation in order to get the prefect picture.
PTZ Control
Functions as a standard keyboard to control the PTZ’s pan tilt
and zoom functions as well as conguring the camera’s settings
and creating or calling presets.
Powering 12V Cameras
The LCD330 features a 12V DC output so that cameras can be
powered by the test monitor.
Video Signal Meter
Displays peak and average video signal strength.
Digital Multimeter
The LCD330 can be used as a digital multimeter to measure
AC and DC voltage and resistance.
UTP Network Cable Tester
Check straight and crossover cables for short circuits and
incorrect terminations.
Video Generator
Creates a colour bar output for checking images and colours
display correctly on composite monitors.
RS485 Data Testing
Displays data from PTZ control equipment so that settings
can be analysed by an engineer.

LCD330 Instruction Book
6
Battery & Power
Power Switch
The On/O switch is located on the right hand side of the
unit. See page 4.
Auto Off
After a period of inactivity the LCD330 will automatically turn
o. To restart the device turn the power switch ‘O ff ’ and then
back ‘On’ again. To see how to set the length of time before the
device automatically turns o see page 7 .
Battery Life
The LCD330 is tted with a high capacity battery providing
up to 10 hours of battery life o of a full charge.
Charging
Only charge the device with the 9V DC PSU supplied. The test
monitor takes 6 hours to charge fully . The charging indicator
will display a solid light when charging which will ash when
the device is fully charged. As a safety feature the LCD330 will
automatically stop drawing power when fully charged.
Checking Battery Level
To view the current battery level enter the ‘System Setup’ from
the main menu (option 1). ‘Battery’is the last item on the page
and battery level is displayed in percent. The battery level will
be displayed as 100 / 90 / 75 / 50 / 25 or 5%. It is recommended
that you charge the LCD330 when the battery level drops to
25% to prevent the battery dying during an installation.
Using The LCD330 When On Charge
You can still use all the features of the LCD330 whilst it is on
charge except the multimeter function.
Selecting Menu Item
To select a menu item simply press they corresponding
number on the keypad.
Note: The rmware version and serial number can not
be selected.
Version & Serial Number
The rmware version and serial number of the product are
displayed at the bottom of the screen.
Main Menu
When the LCD330 is turned on the main menu will be
displayed as shown below.

LCD330 Instruction Book
7
Protocol
Set the protocol of the LCD330 so that it matches that of the
PTZ camera you wish to control. Available protocols:
Pelco D / Pelco P / Samsung / MinKing / VIDO / Yaam / Molynx
/ CSR600 / Alec / Vicon / VideoTrec / AD 485 / DynaColor
/ MLP1 / MLP2 / KDT KB3 / KDT 405 / KDT 304 / LGM /
EVERFOCUS / FASTRAX / SANYO SSP / VCL / ADT / ERNA
/ SIEMENS / HEIJMANS / VISCA / VIDEOTEC / U MACRO /
HONEYWELL / TG.
Com
Set the communication port you wish to use. Available ports:
485 / 232 / 422
Rate (Baud Rate)
Set the baud rate used by the LCD330 so that it matches that
of the PTZ camera you wish to control. Available baud rates:
2400 / 4800 / 9600 / 19200 / 5100
Speed
Set the speed at which PTZs pan and tilt when being controlled.
001 (Min) ~ 016 (Max)
System Setup
In the System Setup menu you can view and congure
system information and PTZ control settings.
Idle Time
Set the period of time in minutes the device has to be inactive
before automatically turning o. To disable automatic power o
set the idle time to 000.
000 ~ 030
Battery
Displays the current battery level.
100 / 90 / 75 / 50 / 25 / 5
How To Congure System Settings
1. At the main menu press ‘1 ’ to enter ‘ SYSTEM SETUP ’.
1. Press the ‘ OPEN/SET ’ to start setup. The rst menu option
will begin to ash on and o.
2. Press the ‘ Up ’ and ‘ Down ’ key to highlight the desired
menu option.
3. Press the ‘ Right ’ arrow to switch to the parameter for
selected menu item.
4. Press ‘ Up ’ or ‘ Down ’ to change the selected parameter.
5. Press ‘ Left ’ to save selection and return to menu item.
6. Press ‘ Left ’ again to nish setup. The menu items will stop
ashing once setup is complete.
7. To return to the main menu press and hold the‘
Menu ’
button for 1 second. The device will beep twice and
display the main menu.

LCD330 Instruction Book
8
Video Testing
Video testing allows you to view the camera’s image during
installation making it easier to position and congure the
camera correctly. It can also be used to check the video signal
at the camera end of the installation when fault nding.
Although primarily used for camera testing, other video
sources such a distributors, quads and DVRs can be
connected to the test monitor for testing video output.
What Information Is Displayed?
As well as the camera’s image, the camera’s address (only
used for PTZ testing) and video format are also displayed. If
no video signal is received the screen will appear black and
the video will read ‘ NULL ’.
Connecting Cameras To The LCD330
To view a camera’s image on the test monitor use the short
BNC lead provided to connect the camera’s video output to
the LCD330’s video input.
12V DC cameras which draw
600mA or less can be powered
by the LCD330 with the 2.1mm power cable supplied. For
more information on powering cameras with the LCD330 see
page 15.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Connection Example
Using The Video Test Function
1. At the main menu press ‘2 ’ to enter ‘ VIDEO AND PTZ TEST ’.
2. To hide the camera’s address and video format press the
‘ MENU ’ button.
3. The screen brightness can be adjusted using the‘ BR+ ’
and ‘ BR- ’ buttons.
4. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
12V DC Power Cable Supplied
(Optional, Max 600mA)
DC 12V
Output
Video
In
BNC To
BNC Lead
Supplied
Camera Video
Output
12V DC 2.1mm
Socket

LCD330 Instruction Book
9
PTZ Testing & Control
The PTZ test function allows you to control and congure
PTZ cameras as you would with a standard keyboard.
What Information Is Displayed?
As well as the camera’s image, the address (ID) of the PTZ
currently being controlled and video format are also displayed.
If no video signal is received the screen will appear black and
the video will read ‘NULL’.
Connecting PTZ Cameras To The LCD330
Connect the PTZ’s video output to the LCD330’s video input
using the BNC to BNC lead provided.
The RS485 test cable supplied is used for connecting the
PTZ’s RS485 contacts to the test monitor. Connect the
‘
Red ’ spring clamp to the PTZ’s ‘ RS485 + ’ contact and the
‘ Black ’ clamp to the ‘ RS485 - ’. On the LCD330 the‘ RS485 + ’ is
connected to terminal ‘ A ’ and the ‘ RS485 - ’ is connected to
terminal ‘ B ’.
PTZs which use
RS422 are connected in the same way as
those which use RS485.
PTZs which communicate using
RS232 are connected to the
RS232 serial port on the left hand side of the test monitor.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Connection Example
RS485 Test
Cable Supplied
+
+
-
-
Video
In
Camera Video
Output
PSU
PTZ
First Things First
Before you can control or congure a PTZ you will need to set
the protocol, communication method and baud rate of the
LCD330 so that they match those of the target PTZ.
The protocol, communication method and baud rate can be
adjusted in the ‘
System Setup ’ menu as explained on page 7.
Using The PTZ Test Function
1. At the main menu press ‘2 ’ to enter ‘ VIDEO AND PTZ TEST ’.
2. To hide the camera’s address and video format press the
‘ MENU ’ button.
3. The screen brightness can be adjusted using the‘ BR+ ’
and ‘ BR- ’ buttons.
4. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
PTZ Address
2. To change the address to that of the PTZ you wish to
control press the ‘ ADDR ’ button.
3. ‘ NEW ADDRESS ’ will now be displayed on screen. Use the
numeric keypad to enter the address of the desired PTZ.
4. Press the ‘ OPEN/SET ’ button to conrm the new address
or ‘ CLOSE/CLEAR ’ to cancel.
The RS485 + must be connected
to terminal ‘ A ’ on the LCD330.
The RS485 - must be connected
to terminal ‘ B ’.
PTZ Testing & Control continues on next page 

LCD330 Instruction Book
10
PTZ Testing & Control Continued
PTZ Control
1. To Pan and Tilt the PTZ simply use the ‘ UP ’, ‘ DOWN ’, ‘ LEFT ’,
and ‘ RIGHT ’ arrow buttons.
2. To adjust the Iris use the ‘ OPEN/SET ’ button to open the
iris and the ‘ CLOSE/CLEAR ’ button to close the iris.
3. To manually adjust the Focus , press the ‘ FAR ’ button to
focus on objects in the distance and the ‘ NEAR ’ button to
focus on objects close to the PTZ.
4. To adjust the Zoom press the ‘ TELE ’ button to zoom in and
the ‘ WIDE ’ button to zoom out.
Settings Presets
1. Position, focus and zoom the PTZ on the desired location
as described on above.
2. Once the PTZ had been position press the‘ SET ’ button.
3. ‘ SAVE PRESET ’ will now be displayed on screen. Use the
numeric keypad to enter the preset number you wish to
assign to the current position the current position.
4. Press the ‘ OPEN/SET ’ button to conrm the new preset
or ‘ CLOSE/CLEAR ’ to cancel.
Calling Presets
1. To recall a save preset press the‘ CALL ’ button.
2. ‘ CALL PRESET ’ will now be displayed on screen. Use the
numeric keypad to enter the preset number you wish
to recall.
3. Press the ‘ OPEN/SET ’ button to conrm input or
‘ CLOSE/CLEAR ’ to cancel.
Conguring PTZ Settings
1. To congure the PTZ’s internal settings you will need to
call the preset which displays the PTZ’s OSD. e.g. Call 95.
2. Use the arrow buttons to navigate the menu system and
alter parameters.
3. Press the ‘ OPEN/SET ’ button to conrm selection and the
‘ CLOSE/CLEAR ’ button to cancel or exit current menu.
Exiting PTZ Test
1. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
Video Signal Analysis
Video signal analysis allows you to check the strength of the
video signal along the cable run in an attempt to nd any
possible faults.
What Information Is Displayed?
When using the video signal analysis function the max peak
to peak voltage of the video signal (MAX Vpp), the average
peak to peak voltage (AVERAGE Vpp) and the sync signal will
be displayed.
Drops in the video or sync signal could result in no image at
the DVR end of the cable run. By testing the video and signal
strength at both the camera and DVR ends of the installation
then comparing the results could highlight any possible
faults. Dierences in sync signals can be used calculate the
impedance of the co-ax cable.
You are likely to encounter problems if the video peak to peak
voltage drops below 0.7V or the sync signal drops below 0.3V.
If no signal is being received‘ NO VIDEO ’ will be displayed.
Connecting Cameras For Video Analysis
To achieve true readings the LCD330 must be connected
in-line with a 75Ω load or a DVR on the cable.
When checking the signal at the
camera end , connect the
camera to the ‘ VIDEO IN ’ socket using the short BNC lead
provided. Connect the LCD330’s ‘ VIDEO OUT ’ socket to the
start of the cable run with the DVR connected at the far end.
12V DC cameras which draw 600mA or less can be powered
by the LCD330 with the 2.1mm power cable supplied.
Video Signal Analysis continues on next page 

LCD330 Instruction Book
11
Using The Video Signal Analysis Function
1. At the main menu press ‘2 ’ to enter ‘ VIDEO AND PTZ TEST ’.
2. Press ‘ 1 ’ to display the video signal analysis.
3. If you wish to refresh the results press‘ 1 ’ again.
4. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
75Ω Load
Of DVR
BNC To BNC
Cable
Video
Out
Video
In
Camera Video
Output
PSU
Video Signal Analysis Continued
For checking the signal at the DVR end, connect the LCD330’s
‘Video Out’socket to the DVR with the short BNC lead
provided. Connect the end of the cable run to the LCD330’s
‘Video In’socket with the camera connected at the start.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Connection Example
UTP Cable Testing
The UTP cable test function can be used to check straight
and crossover network cables for shorts and open circuits.
What Information Is Displayed?
The ‘ UTP CABLE TEST ’ screen shows the termination of each
wire of the CAT5 at both ends of the network cable.
The rst column shows the 8 terminations in order from 1 to
8 in the end of the cable which is plugged into the LCD330.
The second column shows the corresponding terminations at
the opposite end of the network cable.
If a termination in the second column displays a‘
0 ’ there may
be an open circuit in that specic wire. If two terminations
show ‘0’ they may both be open circuits or they could be
short circuiting to each other
The tables below show the correct terminations for both
types of network cable.
UTP Cable Testing continues on next page 
Straight (Patch) Cable
1 ---------- 1
2 ---------- 2
3 ---------- 3
4 ---------- 4
5 ---------- 5
6 ---------- 6
7 ---------- 7
8 ---------- 8
Crossover Cable
1 ---------- 3
2 ---------- 6
3 ---------- 1
4 ---------- 4
5 ---------- 5
6 ---------- 2
7 ---------- 7
8 ---------- 8

LCD330 Instruction Book
12
UTP Cable Testing Continued
Connecting The Network Cable Tester
To preform a network cable test you will need the small
Network Cable Tester supplied with the LCD330.
Plug one end of the cable into the‘
UTP TEST ’ port on the right
hand side of the LCD330. Plug the other end of the network
cable into the Network Cable Tester.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Connection Example
Network Cable
Network Cable
Tester (Supplied)
LCD330
Using The UTP Test Function
1. At the main menu press ‘3 ’ to enter ‘ UTP CABLE TEST ’.
2. Press the ‘ OPEN/SET ’ button to begin cable test.
3. The test results will be displayed allowing you to diagnose
any faults.
4. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
Video Generator
The video generator creates a composite video output to test
that monitors are displaying images and colours correctly.
What Is Displayed?
The ‘ VIDEO GENERATOR ’ will create a colour bar made up
of 7 dierent colours. Alternatively 1 chosen colour can be
displayed full screen.
Connecting The LCD330 To A Monitor
Simply connect the LCD330’s ‘ VIDEO OUT ’ socket to the
monitors video input using the short BNC cable provided. If
the monitor does not have a BNC input you will need to use a
connector such as a BNC to Phono converter.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Video Generator continues on next page 

LCD330 Instruction Book
13
Composite Monitor
BNC To BNC
Cable
Video
Out
Video Generator Continued
Connection Example
Using The Video Generator Function
1. At the main menu press ‘4 ’ to enter ‘ VIDEO GENERATOR ’.
2. A colour bar will be displayed. To display a single colour
full screen press the‘ OPEN/SET ’ button. Repeatedly
pressing the ‘ OPEN/SET ’ button will cycle through the 7
available colours and nally back to the colour bar
3. To display the generated video on the connected monitor
press the ‘ TELE ’ button. When the video is displayed on
the monitor the LCD330’s screen will be blank.
4. To end the test on the connected monitor and return the
image to the test monitor press the ‘ WIDE ’ button.
5. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
Note: The Video Generator function is intended for testing
composite monitors. Trying to display the video on
anything else may result in the video signal not being
recognised at all.
RS485 Data Testing
The RS485 data function allows you to check if PTZ control
equipment is sending data and how it is congured.
What Is Displayed?
The ‘RS485 DATA TEST’displays hexadecimal data sent from the
PTZ control device so that it can be analysed by an engineer.
Connecting A PTZ Controller To The LCD330
Connect the ‘ RS485 + ’ of the PTZ controller to terminal‘ A ’
of the LCD330. The‘ RS485 - ’ of the PTZ controller is then
connected to terminal ‘ B ’.
The locations of the LCD330’s connections are highlighted on
page 4.
Connection Example
RS485 Data Testing continues on next page 
PTZ Control Equipment
‘RS485 +’To ‘A’
‘RS485 -’To ‘B’

LCD330 Instruction Book
14
RS485 Data Testing Continued
Using The RS485 Data Test Function
Note: Before the RS485 data test will function correctly the
baud rate of the LCD330 needs to match that of the PTZ
control equipment. For instructions on setting the baud
rate of the test monitor see page 7.
1. At the main menu press ‘5 ’ to enter ‘ RS485 DATA TEST ’.
2. On the PTZ controller send the command you wish to
analyse. For example move the joystick to the right.
3. The hexadecimal values of the command will be
displayed on the screen of the LCD330.
4. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
Digital Multimeter
The digital multimeter function can be used to measure DC
voltage, AC voltage and resistance.
What Is Displayed?
DC and AC voltage measurements are displayed in volts and
the resistance is measured in ohms. The digital multimeter has
an auto range feature where the most appropriate unit is used
depending on measurement. e.g. Millivolt (mV), Volt (V).
Setting Up The Multimeter
To use the multimeter function you will need to connect the
two voltage probes supplied to the bottom of the unit. The
‘ Red ’ probe is connected to the ‘ VΩ ’ port and the ‘ Black ’ probe
is connected to the ‘ COM ’ port.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Digital Multimeter continues on next page 

LCD330 Instruction Book
15
Using The Digital Multimeter
1. At the main menu press ‘6 ’ to enter ‘ Multimeter ’.
2. Select the required test option by pressing the
corresponding button. Press‘ 1 ’ for ‘ DC VOLTAGE ’, press
‘ 2 ’ for ‘ AC VOLTAGE ’ or press ‘ 3 ’ for ‘ RESISTANCE ’.
Voltage tests are accurate to 0.1mV and the resistance
test is accurate to 0.1Ω.
The
DC voltage test has a test range of 0-1000V .
The AC voltage test has a test range of 0-750V .
The Resistance test has a test range of 0-40MΩ .
3. To return to the main menu press and hold the‘ MENU ’
button for 1 second. The device will beep twice and
display the main menu.
Note: Do not use the multimeter function whilst the LCD330 is
on charge.
Do not test equipment outside the specied test ranges.
Doing so may damage the LCD330.
12V DC Power Output
The LCD330 has a useful 12V DC power output for powering
12V CCTV cameras and equipment. The LDC330 can provide
12V DC power up to a maximum current of 600mA.
Powering Cameras With The LCD330
Connect the narrow end of the supplied 12V DC power cable
to the ‘ DC 12V OUTPUT ’ of the LCD330. The standard 2.1mm
DC plug is then connected to the CCTV camera.
The locations of the LCD330’s connections are highlighted on
page 4. All of the accessories supplied with the test monitor
are displayed on page 5.
Note: Only use LCD330’s power output to power 12V DC
cameras and equipment.
Attempting to power devices which draw more than
600mA will automatically trigger the LCD330’s limiter
and power output will be stopped.
Do not connect the 12V DC output to the LCD330’s 9V
DC input as this may damage the unit.
Connection Example
12V DC Power
Cable (Supplied)
DC 12V
Output
Digital Multimeter Continued
Connection Example
Red To
VΩ
Black To
COM

LCD330 Instruction Book
16
Specication
Feature Function Specication
Video Video Input 1 Channel BNC
Video Output 1 Channel BNC
Format NTSC / PAL (Automatic)
Display 3 Inch LCD Screen / 960 x 240 Resolution
PTZ Protocol Pelco D / Pelco P / Samsung / MinKing / VIDO / Yaam / Molynx / CSR600 / Alec / Vicon / VideoTrec /
AD 485 / DynaColor / MLP1 / MLP2 / KDT KB3 / KDT 405 / KDT 304 / LGM / EVERFOCUS / FASTRAX /
SANYO SSP / VCL / ADT / ERNA / SIEMENS / HEIJMANS / VISCA / VIDEOTEC / U MACRO / HONEYWELL / TG
Communication RS485 / RS422 / RS232
Baud Rate 2400 / 4800 / 5100 / 9600 / 19200
RS485 Input Terminal Strip
RS422 Terminal Strip
RS232 9 Pin RS232 Serial Port
Multimeter DC Voltage Test Range: 0 ~ 1000V / Accuracy: 0.1mV
AC Voltage Test Range: 0 ~ 750V / Accuracy: 0.1mV
Resistance test Range: 0 ~ 40MΩ/ Accuracy: 0.1Ω
Power & Battery Input Power 9V DC
Battery 7.4V 1500mAh Rechargeable battery
Recharge Time 6 Hours
Battery Life 10 Hours
Output Power 12V DC
Max Current Output 600mA
Output Power Battery Life 3 ~ 5 Hours
Other OSD Language English
Working Temperature -30C ~ 70C
Working Humidity 30% ~ 90%
Dimensions 166 x 91 x 48mm
Weight 340g
Warranty
For service and support please contact the original supplier from which the LCD330 was purchased or visit www.cctvmate.com
All specications are approximate. We reserve the right to change any product
specications or features without notice. Whilst every eort is made to
ensure that these instructions are complete and accurate, We cannot be held
responsible in any way for any losses, no matter how they arise, from errors or
omissions in these instructions, or the performance or non-performance of the
equipment that these instructions refer to.
WEE/CG0783SS
This symbol on the products and/or accompanying documents
means that used electronic equipment must not be mixed
with general household waste. For treatment, recovery and
recycling please return this unit to your trade supplier or local
designated collection point as dened by your local council.
© Copyright 2014