Cenocco CC-9093 User manual

Handheld Multi-Purpose
Pressure-Steam Cleaner
Model Number: CC-9093
Owner’s Manual
For correct usage, read these instructions carefully and keep in a safe place
for future reference

WARNING:
•The device should be disconnected from the mains after use and before
cleaning.
•Plug-in power supply and the machine immediately starts heating up. When its heats to specified
temperature, press the steam button, and steam will be sprayed out.
•With complete cleaning accessories supplied, the machine can be assembled and disassembled
easily. It can be used to clean doors, windows, floorboards and much more.
1. Power LED
2. Power Cord and Plug
3. Steam Button
4. Safety Cap
5. Short Spray Nozzle
6. Extended Connecting Spray
7. Measuring Cup
8. Long Spray Cup
9. Funnel
10. Spray Cup with Round Brush
11. Bent Spray Cup
12. Towel Sleeve for Fabric Steamer
Tool
13. Fabric Steamer Tool
14. Window/Door Cleaning Tool
TECHNICAL SPECIFICATION:
Power Supply Rating
AC 220-240 V, 50/60Hz
Total Tank Capacity
350ml
Max. Amt. of Water Needed in the
Tank
250ml
Rated Power
900-1050W
Steam Pressure
0.25-0.32 Mpa
Injected Steam Capacity
28 g/min
Temperature Controller
(Functioning Temperature)
270 °F (132 °F)
Fuser (Functioning Temperature)
332°F (162°C)
Overall Dimension
9.84 x 5.03 x 7.48in
(25cm x 12.8cm x19cm)
Net Weight
2.20 lbs. (1.0kg)

SAFETY PRECAUTIONS:
1. Product must not operate by children without adult supervision
2. To prevent electrical shock, do not immerse power cord or power plug in water or
other liquids
3. The main lead of this appliance is not replaceable by the user. If the supply cord is
damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified person to avoid hazard.
4. This product is for use in household and must not be used for industrial applications.
5. Do not turn on power supply until the tank is full of water
6. Used power supply should comply with the product requirements of the manufacturer
7. During operation, the tank mouth must be hermetically sealed and safety cap should
be tightened in position
8. A socket with ground wire must be used
9. IN USE, THE MACHINE BODY MUST NOT BE TIPPED MORE THAN 45 DEGREES. Tipping it
further will result in boiling water sprayed out together with the steam.
10. Do not direct the steam towards person and animals.
11. Before refilling water, unplug the power cord to disconnect power supply. It is
necessary to unplug the power cord after the machine used before it is cleaned and
while it is repaired.
12. Do not add any rust remover, odor countering agent, alcohol, or detergent into the
tank, as such fluids will damage the tank.
13. Do not use to clean swimming pools.
14. This is not a toy and is not to be used by children.
15. The liquid or steam must not be directed towards equipment containing electrical
components, such as the interior of ovens.
16. DANGER OF SCALDING, OVERFILING THE TANK WILL CAUSE THE STEAM GENERATION
TO BE AFFECTED AND OVERLY HIGH STEAM PRESSURE WILL BE CAUSED.
OPERATING INSTRUCTIONS:
Operation Steps:
1. Unpack the product, check the accessories and documents supplied with the product
and make sure that the product and accessories are not damaged.
2. Before use, please read the User Manual carefully. The steam cleaner is only for use is
households.
3. Place the steam cleaner on a level platform., push down the safety cover, unscrew the
safety cap counterclockwise, and then install the funnel. The safety cap cannot be
opened if there is pressure in broiler to ensure safety for users.
4. THE TOTAL TANK CAPACITY IS 350ML, BUT ONLY PUT A MAXIMUM OF 250ML OF
WATER INTO THE TANK, AS WATER TURNS TO STEAM INSIDE THE TANK, FILLING THE
EMPTY SPACE. IF THERE IS NO EMPTY SPACE INSIDE THE TANK, THE UNIT WILL NOT BE
ABLE TO GENERATE ANY STEAM.
5. Re-install the safety cap and tighten it in position
6. Check the power supply and socket, and confirm they comply with the requirements
given in the User Manual. Then turn on the power supply
7. After it is plugged in, the round light at the bottom will turn on, indicating that the unit
is heating up and pressure is increasing. When the light turns off, it means the Steam
Cleaner is ready for use. At this time, lightly press the steam button and check whether
steam is sprayed out of the nozzle. (Do not aim the spray nozzle at other persons or
objects).
8. I there is steam sprayed out, please install suitable accessories according to your needs
after you release the button.
9. Press down the steam button again to carry out the operations required by you.
After the machine is used:
1. After the cleaning is used, unplug the power cord, and disconnect the supply.
2. Press down the steam button to release the pressure until no steam is injected out.
3. Slowly unscrew the safety cap but do not remove it. Then place the machine in a cool
place it down for about five minutes. Finally, completely remove the safety cap.
4. Empty the residual water in the tank and clean the external surface with a piece of dry
cloth.
5. Then re-install the safety cap onto the machine body tighten it in position
NOTE: Re-install the safety cap onto the machine body and tighten it in
position.

INSTALLATION OF ACCESSORIES:
Installing the spray cup with brush:
1. Hold the pipe section of the spray cup with brush in
your hand.
2. Align the arrow on the spray cup with the single-line
mark on short spray nozzle on the machine body.
3. Insert the spray cup in position.
4. Rotate the spray cup in clockwise direction.
5. Align the arrow on the spray cup with the double-line
mark on short spray nozzle on the machine body, as
shown in (Figure 1)
6. Fix the spray cup on the machine body.
To remove the spray cup with brush:
1. Rotate the spray cup inversely (counterclockwise) as
shown in (Figure 2).
2. Align the arrow on the spray cup with the single-line
mark on the machine body.
3. The spray cup with brush can now be pulled out.
Installation of short spray cup:
The long spray cup is installed in the same method as the
installation of spray cup with brush.
Installation of short spray nozzle:
1. Aim the spray cup with round brush or bent spray cup
at the top of spray nozzle, as shown in (Figure 3).
2. Push the spray cup upwards until it is in position
3. As the short spray nozzle and spray cup are positioned
in six directions, the angle and direction can be
adjusted during the installation.
Installation of round brush cup and bent spray cup:
The spray cup with round brush, the bent spray cup and the
long spray cup can be installed in the same procedure as the
installation on short spray nozzle.
Use of Fabric Steamer Tool
1. Place towel sleeve (12) over the fabric steamer tool (13)
2. Attached to the extended connecting spray (6) for
refreshing and removing wrinkles on the clothing or
drapes
3. Hang clothing from a shower rod or clothes hook using a
sturdy clothes hanger.
4. Activate steam cleaner and move tool over fabric, taking
care not to concentrate steam in single area.
Installation of windows/door cleaning tool
1. To clean windows and doors easily, attach the
window/door cleaning tool (14) to the fabric steamer
tool (13)
2. First, remove towel sleeve (12) from fabric steamer tools
(13) then hook and click into window/door cleaning tool.
3. Attach the accessory to the extended connecting spray
and clean your windows and doors easily with the
rubber wiper. (Figure 4.)
4. To remove the window/door cleaning tool, simply pull
the tab to release the fabric steamer tool (Figure 5.).
To refill the water during operation:
1. Unplug the power cord and disconnect the power supply
2. Press down the steam button to release the pressure
until no steam is sprayed out.
3. Slowly unscrew the safety cap but do not remove it, and
residual steam will be discharged slowly until no steam
comes out.
4. Place the machine in a cool place to cool it down for
about five minutes. Finally, completely remove the
safety cap.
5. Use the funnel and measuring cup to refill a suitable
quantity of cold or hot water into the tank.
6. Re-install the safety cap onto the machine body and
tighten it in position
FIGURE 1
FIGURE 2
FIGURE 4
FIGURE 3
FIGURE 5