Central Machinery 93762 Installation manual

HORIZONTAL/VERTICAL
METAL CUTTING BANDSAW
Model 93762
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improve-
ments, actual product may differ slightly from the product described herein. Tools required for assembly
and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 11h

SKU 93762 For technical questions, please call 1-800-444-3353. Page 2
CONTENTS
IMPORTANT SAFETY
INFORMATION ........................... 3
GENERAL TOOL SAFETY
WARNINGS..................................... 3
BAND SAW SAFETY WARNINGS.... 5
VIBRATION SAFETY ................... 7
GROUNDING INSTRUCTIONS .... 7
GROUNDED TOOLS: TOOLS
WITH THREE PRONG PLUGS ...... 7
DOUBLE INSULATED TOOLS:
TOOLS WITH TWO PRONG
PLUGS ............................................ 8
SPECIFICATIONS......................... 9
UNPACKING ................................. 9
ASSEMBLY INSTRUCTIONS....... 9
TO ASSEMBLE THE STAND: ..... 9
TO ATTACH THE WHEELS TO
THE STAND:.............................. 9
TO ATTACH THE BANDSAW
TO THE STAND:...................... 10
TO ATTACH THE STOCK
STOP ASSEMBLY:.................. 10
TO ATTACH THE PULLEY
COVER: ................................... 11
TO ATTACH THE SPINDLE
PULLEY AND MOTOR
PULLEY:.................................. 11
TO INSTALL THE V-BELT: ........ 11
TO ADJUST THE CUTTING
SPEED:.................................... 11
TO CONVERT THE BANDSAW
FOR VERTICAL USE: ............. 12
OPERATING INSTRUCTIONS ... 14
TO USE THE VISE:.................... 14
TO USE THE QUICK VISE
ADJUSTMENT FOR AN
ANGLE CUT: ........................... 14
ADJUSTMENTS .............................. 15
TO ADJUST THE STOCK
STOP: ...................................... 15
ADJUSTING THE BLADE
GUIDE BEARINGS: ................ 15
ADJUSTING THE BLADE
TRACKING:............................. 15
ADJUSTING THE BLADE
TENSION:................................ 16
ADJUSTING THE FEED RATE: 17
ADJUSTING THE BLADE
GUIDE BRACKETS: ............... 17
BASIC BANDSAW OPERATION --
VERTICAL POSITION: ................. 18
BASIC BANDSAW OPERATION --
HORIZONTAL POSITION:............ 19
INSPECTION, MAINTENANCE,
AND CLEANING....................... 21
TROUBLESHOOTING..................... 24
PARTS LIST................................ 25
ASSEMBLY DIAGRAM............... 27

SKU 93762 For technical questions, please call 1-800-444-3353. Page 3
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information provid-
ed with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Tool Safety Warnings
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future reference.
KEEP GUARDS IN PLACE and in1.
working order.
REMOVE ADJUSTING KEYS AND2.
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning it on.
KEEP WORK AREA CLEAN. Clut-3.
tered areas and benches invite ac-
cidents.
DON’T USE IN DANGEROUS EN-4.
VIRONMENT. Don’t use power tools
in damp or wet locations, or expose
them to rain. Keep work area well
lighted.
KEEP CHILDREN AWAY. All visitors5.
should be kept safe distance from
work area.
MAKE WORKSHOP KID PROOF6.
with padlocks, master switches, or by
removing starter keys.

SKU 93762 For technical questions, please call 1-800-444-3353. Page 4
DON’T FORCE TOOL. It will do the7.
job better and safer at the rate for
which it was designed.
USE RIGHT TOOL. Don’t force tool8.
or attachment to do a job for which it
was not designed.
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS
(120 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25’ 50’ 100’ 150’
0 – 6 18 16 16 14
6.1 – 10 18 16 14 12
10.1 – 12 16 16 14 12
12.1 – 16 14 12 Do not use.
TABLE A
USE PROPER EXTENSION CORD.9.
Make sure your extension cord is
in good condition. When using an
extension cord, be sure to use one
heavy enough to carry the current
your product will draw. An undersized
cord will cause a drop in line voltage
resulting in loss of power and over-
heating. Table A shows the correct
size to use depending on cord length
and nameplate ampere rating. If in
doubt, use the next heavier gage.
The smaller the gage number, the
heavier the cord.
WEAR PROPER APPAREL. Do not10.
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewelry
which may get caught in moving
parts. Nonslip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
ALWAYS USE SAFETY GLASSES.11.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a12.
vise to hold work when practical. It’s
safer than using your hand and it
frees both hands to operate tool.
DON’T OVERREACH. Keep proper13.
footing and balance at all times.
MAINTAIN TOOLS WITH CARE.14.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and chang-
ing accessories.
DISCONNECT TOOLS before ser-15.
vicing; when changing accessories,
such as blades, bits, cutters, and the
like.
REDUCE THE RISK OF UNINTEN-16.
TIONAL STARTING. Make sure
switch is in off position before plug-
ging in.
USE RECOMMENDED ACCESSO-17.
RIES. Consult the owner’s manual for
recommended accessories. The use
of improper accessories may cause
risk of injury to persons.
NEVER STAND ON TOOL. Serious18.
injury could occur if the tool is tipped
or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS. Before19.
further use of the tool, a guard or
other part that is damaged should
be carefully checked to determine
that it will operate properly and per-
form its intended function – check for
alignment of moving parts, binding
of moving parts, breakage of parts,
mounting, and any other conditions
that may affect its operation. A guard

SKU 93762 For technical questions, please call 1-800-444-3353. Page 5
or other part that is damaged should
be properly repaired or replaced.
DIRECTION OF FEED. Feed work20.
into a blade or cutter against the
direction of rotation of the blade or
cutter only.
NEVER LEAVE TOOL RUNNING21.
UNATTENDED. TURN POWER OFF.
Don’t leave tool until it comes to a
complete stop.
Band Saw Safety Warnings
For Your Own Safety Read Instruction
Manual Before Operating Saw
Wear eye protection.1.
Do not remove jammed cutoff pieces2.
until blade has stopped.
Maintain proper adjustment of blade3.
tension, blade guides, and thrust
bearings.
Adjust upper guide to just clear work-4.
piece.
Hold workpiece rmly against table.5.
Keep hands away from cutting area6.
and Saw Blade.
Properly adjust the upper blade7.
guide, blade tension and thrust bear-
ing before each use to reduce the risk
of injury. See Operating Instructions
for explanation of needed adjust-
ments.
Never leave the Bandsaw unattended8.
when it is plugged into an electrical
outlet. Turn off the tool, and unplug
it from its electrical outlet before leav-
ing.
Make sure the Bandsaw is located on9.
a at, level, sturdy surface capable
of supporting the weight of the Saw
and workpieces. Always “chock” the
Wheels to prevent the Bandsaw from
accidentally moving.
Before using the Bandsaw, check to10.
make sure the Saw Blade is properly
mounted and is not cracked or bent.
Never attempt to cut more than one11.
workpiece at a time.
Never attempt to cut freehand. Make12.
sure the workpiece to be cut is
pressed rmly against the Table and/
or secured in the Vise.
When cutting a large workpiece,13.
make sure its entire length is properly
supported. If necessary, use a roller
stand (not included).
Do not lean on the Bandsaw when14.
the tool is in its upright position.
When moving the Bandsaw, always15.
have its Head lowered to its horizon-
tal position and the Locking Pin (115)
inserted in the Pivot (120).
Allow the Saw Blade to rotate to full16.
speed before feeding a workpiece
into the Blade. When turning off the
Bandsaw, allow the Saw Blade to
spin down and stop on its own. Do
not press against the Saw Blade to
stop it.
Wear heavy-duty work gloves when17.
changing the Saw Blade.
Turn off the Bandsaw and allow the18.
Saw Blade to completely stop if the
Saw Blade is to be backed out of an
uncompleted cut.

SKU 93762 For technical questions, please call 1-800-444-3353. Page 6
Keep all safety guards in place and in19.
proper working order.
Use indoors only.20.
If the teeth of the Saw Blade are so21.
far apart that they straddle the work-
piece, severe damage to the work-
piece and/or Saw Blade will result.
The use of accessories or attach-22.
ments not recommended by the
manufacturer may result in a risk of
injury to persons.
When servicing use only identical23.
replacement parts.
Only use safety equipment that has24.
been approved by an appropriate
standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breath-
ing protection must be NIOSH-ap-
proved for the specic hazards in the
work area.
Industrial applications must follow25.
OSHA guidelines.
Maintain labels and nameplates on26.
the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
Avoid unintentional starting. Prepare27.
to begin work before turning on the
tool.
People with pacemakers should28.
consult their physician(s) before use.
Electromagnetic elds in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit Inter-
rupter (GFCI) should also be imple-
mented – it prevents sustained elec-
trical shock.
Some dust created by power sand-29.
ing, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of Cali-
fornia] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and ce-
ment or other masonry products
• Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures var-
ies, depending on how often you do
this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to lter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
WARNING: Handling the cord on30.
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
The warnings, precautions, and in-31.
structions discussed in this instruction
manual cannot cover all possible con-

SKU 93762 For technical questions, please call 1-800-444-3353. Page 7
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Vibration Safety
This tool vibrates during use. Re-
peated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
Anyone using vibrating tools regu-1.
larly or for an extended period should
rst be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries, ner-
vous system disorders, diabetes, or
Raynaud’s Disease should not use
this tool. If you feel any medical or
physical symptoms related to vibra-
tion (such as tingling, numbness, and
white or blue ngers), seek medical
advice as soon as possible.
Do not smoke during use. Nico-2.
tine reduces the blood supply to the
hands and ngers, increasing the risk
of vibration-related injury.
Wear suitable gloves to reduce the3.
vibration effects on the user.
Use tools with the lowest vibration4.
when there is a choice between dif-
ferent processes.
Include vibration-free periods each5.
day of work.
Grip tool as lightly as possible (while6.
still keeping safe control of it). Let
the tool do the work.
To reduce vibration, maintain the tool7.
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
SAVE THESE
INSTRUCTIONS.
GROUNDING INSTRUCTIONS
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION
READ AND FOLLOW THESE
INSTRUCTIONS:
Grounded Tools: Tools with Three
Prong Plugs
In the event of a malfunction or1.
breakdown, grounding provides a
path of least resistance for electric
current to reduce the risk of electric
shock. This tool is equipped with an
electric cord having an equipment-
grounding conductor and a ground-
ing plug. The plug must be plugged
into a matching outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided – if it2.
will not t the outlet, have the proper
outlet installed by a qualied electri-
cian.

SKU 93762 For technical questions, please call 1-800-444-3353. Page 8
Improper connection of the equip-3.
ment-grounding conductor can re-
sult in a risk of electric shock. The
conductor with insulation having an
outer surface that is green with or
without yellow stripes is the equip-
ment-grounding conductor. If repair
or replacement of the electric cord or
plug is necessary, do not connect the
equipment-grounding conductor to a
live terminal.
Check with a qualied electrician or 4.
service personnel if the grounding
instructions are not completely under-
stood, or if in doubt as to whether the
tool is properly grounded.
Use only 3-wire extension cords that5.
have 3-prong grounding plugs and
3-pole receptacles that accept the
tool’s plug.
Repair or replace damaged or worn6.
cord immediately.
7. This tool is intended for use on a cir-
cuit that has an outlet that looks like
the one illustrated above in 125 V~
3-Prong Plug and Outlet. The tool
has a grounding plug that looks like
the plug illustrated above in 125 V~
3-Prong Plug and Outlet.
The outlet must be properly installed8.
and grounded in accordance with all
codes and ordinances.
Do not use an adapter to connect this9.
tool to a different outlet.
Double Insulated Tools: Tools
with Two Prong Plugs
To reduce the risk of electric shock,1.
double insulated equipment has a po-
larized plug (one blade is wider than
the other). This plug will t in a polar-
ized outlet only one way. If the plug
does not t fully in the outlet, reverse
the plug. If it still does not t, contact
a qualied electrician to install the
proper outlet. Do not change the plug
in any way.
Double insulated tools may be used2.
in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 9
SPECIFICATIONS
Motor 120 V~ / 60 Hz / 1 HP / n01700/min
Cutting Capacity 4-1/2” Round Stock /
4” x 6” Rectangular Stock
Speeds 80 FPM / 120 FPM / 200 FPM
Throat Depth 4-1/2”
Angle Cutting
Capacity
0° ~ 55° (Left) Miter Plate on
Horizontal Cutting Bed
Blade 64” L x 15/32” W x 0.025” Thick /
14 TPI
Horizontal Bed 11-1/2” L x 7-1/2” W x 23-1/2” Height
Vertical Bed 9-5/8” L x 9-1/2” W x 33-1/2” Height
V-Belt Type 0-506
UNPACKING
When unpacking, check to make sure
all the parts shown on the Parts Lists on
pages 31 and 32 are included. If any
parts are missing or broken, please call
Harbor Freight Tools at the number shown
on the cover of this manual as soon as
possible.
ASSEMBLY INSTRUCTIONS
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram on
page 33.
CAUTION! Always make sure the Power
Switch (164) for the Bandsaw is in
its “OFF” position and the tool is
unplugged from its electrical outlet
prior to assembling the tool, adding
any accessories, or making adjust-
ments to the tool.
To Assemble The Stand:
PULL
HANDLE
(173)
TOOL PLATE
(175)
STAND
(174)
STAND
(174)
FLAT WASHER
(177)
SCREW
(178)
NUT
(176)
PIN
(172)
FLAT WASHER
(180)
NUT
(181)
HEX BOLT (183)
FLAT
WASHER
(184)
SPRING WASHER (185)
PIN
(188)
WHEEL SHAFT
(187)
WHEEL (182)
WHEEL
BRACKET
(186)
FIGURE A
1. Insert the Pull Handle (173) into the
two mounting holes located in the up-
per section of one Stand (174). Then
secure the Pull Handle to the Stand,
using two Pins (172).
(See Figure A.)
Attach one end of the Tool Plate2.
(175) to the upper section of one
Stand (174), using two Screws (178),
two Flat Washers (177), and two Nuts
(176). (See Figure A.)
Attach the other end of the Tool3.
Plate (175) to the upper section of
the remaining Stand (174), using
two Screws (178), two Flat Washers
(177), and two Nuts (176).
(See Figure A.)
To Attach The Wheels To The Stand:
Align the two mounting holes in the
Wheel Bracket (186) with the two
mounting holes located in the lower
section of the Stand (174). Then se-
cure the Wheel Bracket to the Stand,
using two Hex Bolts (183), two Spring
Washers (185), two Flat Washers
(184), two Flat Washers (180), and
two Nuts (181). (See Figure A.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 10
To Attach The Bandsaw To The Stand:
STAND
(TOP VIEW)
MOUNTING HOLE
MOUNTING HOLE
MOUNTING HOLE
MOUNTING HOLE MOUNTING HOLE
MOUNTING HOLE
SCREW (59)
SPRING WASHER (58)
FLAT WASHER (57)
FIGURE B
1. With additional manpower, and an
adequate lifting device, carefully set
the Bandsaw on top of the Stand as-
sembly, making sure the upper sec-
tion of the Stand ts outside the base
of the Bandsaw. (See Figure B.)
Align the2. three threaded mounting
holes in each end at the base of
the Bandsaw with the three mount-
ing holes located at each end of the
Stand assembly. Then secure the
Bandsaw to the Stand assembly, us-
ing three Screws (59), three Spring
Washers (58), and three Flat Wash-
ers (57). (See Figure B.)
To Attach The Stock Stop Assembly:
When mounted to the Bandsaw, the1.
adjustable Stock Stop assembly is
used to make repetitive cuts of the
same length.
FIGURE C
STOCK
STOP (157)
SOCKET HEAD
SCREW (156)
SHAFT (158)
HEX BOLT (149)
END VIEW
WITH
HAND WHEEL (171)
IN FOREGROUND
2. To attach the Stock Stop assembly,
slide the Shaft (158) into the mount-
ing hole in the Machine Bed (142),
and secure the Shaft by tightening
the Hex Bolt (149). (See Figure C)
Slide the Stock Stop (157) onto the3.
Shaft (158), and secure by tightening
the Socket Head Screw (156).
(See Figure C.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 11
To Attach The Pulley Cover:
PULLEY
COVER (72)
WORM
SHAFT (9)
MOTOR
SHAFT (81)
BODY
FRAME (60)
HEX BOLT (76)
FLAT WASHER (77)
FIGURE D
Position the Pulley Cover (72) over
the Worm Shaft (9) and Motor Shaft
(81). Align the mounting hole in the
Pulley Cover with the mounting hole
in the Body Frame (60). Then secure
the Pulley Cover to the Bandsaw,
using one Hex Bolt (76) and one Flat
Washer (77). (See Figure D.)
To Attach The Spindle Pulley And Motor
Pulley:
MOTOR PULLEY (79)
SHAFT KEY (80)
(NOT SHOWN)
SPINDLE PULLEY (1)
V-BELT (10)
FIGURE E
1. Slide the Spindle Pulley (1) fully onto
the Worm Shaft (9). Then secure the
Spindle Pulley to the Worm Shaft,
using one Socket Head Screw (2).
(See Figure E.)
Insert the Shaft Key (80) in the slot2.
on the Motor Shaft (81). Align the
slot in the Motor Pulley (79) with
the Shaft Key. Slide the Motor Pul-
ley fully onto the Motor Shaft. Then
secure the Motor Pulley to the Motor
Shaft, using one Socket Head Screw
(2). (See Figure E.)
To Install The V-Belt:
FIGURE F
HEX BOLT (70)
MOTOR (81)
The V-Belt (10) can be installed by
loosening the Hex Bolt (70) and mov-
ing the Motor (81) forward. Place the
V-Belt around the top grooves in the
Spindle Pulley (1) and Motor Pulley
(79). Next, move the Motor back-
wards to tighten the tension on the
V-Belt. Then, re-tighten the Hex Bolt
to secure the Motor in place.
(See Figures E and F.)
To Adjust The Cutting Speed:
The Bandsaw is designed to cut at1.
three different speeds: 80, 120, and
200 FPM (Feet Per Minute) depend-
ing on the type of material being cut.

SKU 93762 For technical questions, please call 1-800-444-3353. Page 12
MATERIAL SPEED
(FPM)
PULLEY GROOVE
SPINDLE MOTOR
Tool Steel,
Stainless
Alloy Steels,
Bearing
Bronze
80 Large Small
Medium to High
Carbon Steels,
Hard Brass or
Bronze
120 Medium Medium
Low to Medium
Carbon Steels,
Soft Brass,
Aluminum,
Plastic
200 Small Large
Refer to the Chart above to deter-2.
mine the proper cutting speed for a
specic type of material being cut.
SPINDLE PULLEY MOTOR PULLEY
SMALL
SMALL
MEDIUM MEDIUM
LARGE
LARGE
FIGURE G
3. The cutting speed can be adjusted by
loosening the Hex Bolt (70) and mov-
ing the Motor (81) forward. Place the
V-Belt around the desired grooves in
the Spindle Pulley (1) and Motor Pul-
ley (79). Next, move the Motor back-
wards to tighten the tension on the
V-Belt. Then, re-tighten the Hex Bolt
to secure the Motor in place.
(See Figures E, F, and G.)
4. WARNING! Always securely
close the Lid on the Pulley Cover
(72) after installing a V-Belt (10) or
adjusting the cutting speed.
To Convert The Bandsaw For Vertical
Use:
NOTE: Notching, slitting, and contour
work is best done with the Bandsaw
in its vertical position.
FIGURE H
SUPPORT
PLATE (150) BODY
FRAME
(60)
LOCKING
PIN (153)
1. Raise the Saw Head to its full verti-
cal position, making sure it locks in
position by turning the Support Plate
(150) to the right until it rmly locks
into the Body Frame (60) and insert-
ing the Locking Pin (153).
(See Figure H.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 13
SCREW (190)
SMALL VERTICAL CUTTING PLATE (194)
FIGURE I
SCREW (190)VERTICAL CUTTING PLATE (189)
2. Remove the two Screws (190), and
remove the Small Vertical Cutting
Plate (194). (See Figure I.)
Guide the Saw Blade (82) through3.
the slot in the Vertical Cutting Plate
(189), and secure it in position with
the two Screws (190).
(See Figure I.)
HEX HEAD BOLT (61)
VERTICAL CUTTING
PLATE (189) SCREW (190)
FLAT WASHER (192)
NUT (193)
VERTICAL CUTTING
PLATE SUPPORT (191)
FIGURE J
4. Insert one Screw (190) downward
through the mounting hole in the
Vertical Cutting Plate (189). Attach
the top section of the Vertical Cutting
Plate Support (191) to the Vertical
Cutting Plate (189), using one Flat
Washer (192) and one Nut (193).
Remove the Hex Head Bolt (61).
Position the Vertical Cutting Plate
Support against the Body Frame (60).
Then rmly re-tighten the Hex Head
Bolt. (See Figures I and J.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 14
OPERATING INSTRUCTIONS
CAUTION! Turn the Power Switch
(164) to its “OFF” position and un-
plug the tool from its electrical outlet
prior to making adjustments to the
tool.
To Use The Vise:
Raise the Body Frame (60) to its1.
vertical position, and lock the Body
Frame in place with the Support Plate
(150) and Locking Pin (153).
(See Figure H.)
FIGURE K
MOVEABLE VISE PLATE (141)
HAND
WHEEL
(171)
MACHINE BED (142)
2. Open the Moveable Vise Plate (141)
to accept the piece of material to be
cut by rotating the Hand Wheel (171)
counterclockwise. (See Figure K.)
Place the workpiece on the Machine3.
Bed (142). If the workpiece is long,
support the end. (See Figure K.)
Clamp the workpiece rmly with the 4.
Moveable Vise Plate (141) by rotat-
ing the Hand Wheel (171) clockwise.
(See Figure K.)
To Use The Quick Vise Adjustment For
An Angle Cut:
Loosen the Hex Bolt (136), and move
the Mitering Vise Plate (138) to the
threaded hole position. Adjust the
Mitering Vise Plate to the desired
angle as indicated by the Angle Scale
(165). Loosen the Hex Bolt (139),
and adjust the Moveable Vise Plate
(141) to parallel the Mitering Vise
Plate. Then, re-tighten the Hex Bolt.
(See Figure L.)
THREADED
HOLE POSITION
MITERING
VISE
PLATE
(138)
HEX BOLT
(136)
ANGLE SCALE
(165)
MOVEABLE
VISE
PLATE
(141)
HEX BOLT
(139)
FIGURE L

SKU 93762 For technical questions, please call 1-800-444-3353. Page 15
Adjustments
To Adjust The Stock Stop:
SHAFT (158)
SOCKET HEAD
SCREW (156)
STOCK
STOP
(157)
WORKPIECE
(NOT INCLUDED)
FIGURE M
1. Loosen the Socket Head Screw (156)
that holds the Stock Stop (157) to the
Shaft (158). (See Figure M.)
Adjust the Stock Stop (157) to the2.
desired length position. Then, re-
tighten the Socket Head Screw (156).
(See Figure M.)
Adjusting The Blade Guide Bearings:
NOTE: Blade Guide Bearings (88, 92,
100, 104) adjustment is a critical fac-
tor in the performance of the Band-
saw.
It is always best to try a new Saw1.
Blade (82) to see if it will correct poor
cutting before attempting to adjust the
Blade Guide Bearings. For example,
if a Saw Blade becomes dull on one
side sooner than the other, it will
begin cutting crooked. A Saw Blade
replacement will correct this prob-
lem, whereas Blade Guide Bearings
adjustment will not.
SHAFT
(91, 103)
OUTER BLADE
GUIDE BEARING
(92, 104)
INNER BLADE
GUIDE BEARING
(88, 100)
NUT (86, 96)
(NOT SHOWN)
SHAFT
(91, 103)
SAW BLADE (82)
FIGURE N
2. If a new Saw Blade does not correct
the problem, check the Blade Adjust-
able Seats (83, 110) to obtain the
proper clearance. (See Figure N.)
There should be from .000” (just3.
touching) to .001” clearance between
the Saw Blade and Blade Guide
Bearings (88, 92, 100, 104). To ob-
tain this clearance adjust as follows:
Thea. Outer Blade Guide Bearings
(92, 104) are mounted to Shafts (91,
103) and can be adjusted.
(See Figure N.)
Loosen the Nuts (86, 96) while hold-b.
ing the Shafts (91, 103) with a Hex
Key (not included). (See Figure N.)
Position the Shafts (91, 103) by turn-c.
ing it to the desired position of clear-
ance. Then, re-tighten the Nuts (86,
96). (See Figure N.)
Adjust thed. Inner Blade Guide Bear-
ings (88, 100) in the same manner.
Adjusting The Blade Tracking:
Raise the Saw Head to its full verti-1.
cal position, making sure it locks in
position by turning the Support Plate
(150) to the right until it rmly locks
into the Body Frame (60) and insert-

SKU 93762 For technical questions, please call 1-800-444-3353. Page 16
ing the Locking Pin (153).
(See Figure H.)
Turn on the Bandsaw. The Saw2.
Blade (82) is tracking properly when
the back of the Blade is just touch-
ing the edge of the Blade Wheel (37)
ange. The back of the Blade should
not be rubbing against the ange.
(See Figure P.)
If adjustment is necessary, the Blade3.
Guide Bearings (88, 92, 100, 104)
should be clear of the Saw Blade
(82). (See Figure N.)
HEX BOLT (21)
LOWER SCREW (22)
BLADE TENSION
ADJUSTING KNOB
(34)
BLADE WHEEL
(37)
FIGURE O
4. Loosen the middle Hex Bolt (21) to a
point where it is loose but snug.
(See Figure O.)
With the Bandsaw running, turn the5.
lower Screw (22) until the Saw Blade
(82) is tracking properly, making sure
Blade tension is maintained by turn-
ing the Blade Tension Adjusting Knob
(34). (See Figure O.)
Re-tighten the middle Hex Bolt (21)6.
when adjustment is complete.
(See Figure O.)
Adjusting The Blade Tension:
BLADE TENSION
ADJUSTING KNOB (34)
BLADE
WHEEL (37)
BLADE
WHEEL (54)
SAW
BLADE
(82)
BLADE
BACK
COVER
(114)
FIGURE P
1. Turn the Blade Tension Adjusting
Knob (34) clockwise to increase ten-
sion on the Saw Blade (82). Turn the
Blade Tension Adjusting Knob coun-
terclockwise to decrease tension on
the Saw Blade. Correct tension is
acquired when the Saw Blade is just
tight enough so that no slippage oc-
curs between the Saw Blade and the
Blade Wheels (37, 54).
(See Figure P.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 17
When the Bandsaw is not in use over2.
long periods of time, release the ten-
sion on the Saw Blade (82).
Adjusting The Feed Rate:
FIGURE Q
HANDLE
(127)
The feed rate of the Body Frame (60)
can be adjusted by turning the Han-
dle (127) clockwise to decrease the
feed rate or counterclockwise to in-
crease the feed rate. Do not turn the
Handle more than one turn at a time.
Excessive feed pressure can break
the Saw Blade (82). Insufcient feed
pressure dulls the Saw Blade rapidly.
(See Figure Q.)
Adjusting The Blade Guide Brackets:
BLADE GUIDE BRACKETS
(90, 102)
GUIDE
ADJUSTING
KNOB (45)
FIGURE R
1. The Right Blade Guide Bracket (90)
and Left Blade Guide Bracket (102)
are adjustable by loosening the
Guide Adjusting Knob (45) and sliding
the Brackets up or down to accom-
modate the depth of the workpiece.
(See Figure R.)
The Blade Guide Brackets (90, 102)2.
should be set as close as possible
to the workpiece, without interfering
with the workpiece or contacting the
Machine Bed (142). (See Figure R.)
Once the adjustment is made, make3.
sure to re-tighten the Guide Adjusting
Knob (45). (See Figure R.)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 18
Basic Bandsaw Operation --
Vertical Position:
1. WARNING! Always wear ANSI-
approved safety impact eye goggles
when operating the Bandsaw.
Do not plug the Power Cord Plug2.
into an electrical outlet until all
necessary adjustments (as previ-
ously discussed in this manual)
have been made.
FIGURE S
SAW BLADE
(82)
VERTICAL CUTTING
PLATE (189)
POWER SWITCH (164)
BODY
FRAME
(60)
SUPPORT
PLATE (150)
LOCKING
PIN (153)
3. Raise the Body Frame (60) to its full
vertical position, making sure it locks
in place by turning the Support Plate
(150) to the right until it rmly locks
into the Body Frame and inserting the
Locking Pin (153). (See Figure S.)
Once all necessary adjustments to4.
the Bandsaw have been made, plug
the Power Cord Plug into the near-
est 120 volt, grounded, electrical
outlet.
Turn the Power Switch (164) to its5.
“ON” position. (See Figure S.)
6. CAUTION! Cut only at workpiec-
es when the Bandsaw is in its vertical
position. Never attempt to cut pipes
or other round objects with the Band-
saw in its vertical position.
Before cutting, turn on the Bandsaw7.
and check for excessively loose Saw
Blade (82) tension or machine vi-
bration. If this is found, turn off the
Bandsaw and correct the problem
before using. (See Figure S.)
Set the workpiece on the Vertical Cut-8.
ting Plate (189), making sure to keep
downward pressure on the workpiece
throughout the cutting process.
(See Figure S.)
When cutting a large workpiece,9.
make sure its entire length is properly
supported. If necessary, use a roller
stand (not included) with a larger
workpiece.
Allow the Saw Blade (82) to turn up10.
to full speed before feeding the work-
piece into the Saw Blade.
(See Figure S.)
11. WARNING! Keep hands and
ngers safely away from the cut-
ting area.
Feed the workpiece into the Saw12.
Blade (82) gradually. Do not force
the Bandsaw to remove material
faster than it is designed to cut.
(See Figure S.)
Never attempt to remove mate-13.
rial stuck in the moving parts of the
Bandsaw while it is plugged in and
running. Turn off the Bandsaw if the
workpiece is to be backed out of an
uncompleted cut.
Once the cut is made, turn the Power14.
Switch (164) to its “OFF” position.
Then, unplug the Power Cord Plug

SKU 93762 For technical questions, please call 1-800-444-3353. Page 19
from its electrical outlet.
(See Figure S.)
Wait until the Saw Blade (82) comes15.
to a complete stop. Then, remove
the workpiece and scrap material
from the Vertical Cutting Plate (189).
(See Figure S.)
Remove the Locking Pin (153) and16.
turn the Support Plate (150) to the
left. Then, lower the Body Frame
(60) to its horizontal position.
(See Figure S.)
Basic Bandsaw Operation --
Horizontal Position:
1. WARNING! Always wear ANSI-
approved safety impact eye goggles
when operating the Bandsaw.
Do not plug the Power Cord Plug2.
into an electrical outlet until all
necessary adjustments (as previ-
ously discussed in this manual)
have been made.
3. Raise the Body Frame (60) to its full
vertical position, making sure it locks
in place by turning the Support Plate
(150) to the right until it rmly locks
into the Body Frame and inserting the
Locking Pin (153). (See Figure S.)
Secure the workpiece in the Vise as-4.
sembly (138, 141). When cutting a
large workpiece, make sure its entire
length is properly supported. If nec-
essary, use a roller stand (not includ-
ed) with a larger workpiece.
(See Figure T.)
If cutting several workpieces at the5.
same length, you may wish to adjust
the Stock Stop (157) to the desired
position. (See Figure T.)
Once all necessary adjustments to6.
the Bandsaw have been made, plug
the Power Cord Plug into the near-
est 120 volt, grounded, electrical
outlet. (See Figure T.)
Turn the Power Switch (164) to its7.
“ON” position, and slowly lower the
Body Frame (60) until the Saw Blade
(82) is just above the workpiece cut
line. (See Figure T.)
Before cutting, turn on the Bandsaw8.
and check for excessively loose Saw
Blade (82) tension or machine vi-
bration. If this is found, turn off the
Bandsaw and correct the problem
before using. (See Figure T.)
Allow the Saw Blade (82) to turn up9.
to full speed before feeding the Saw
VISE ASSY.
(138, 141)
STOCK STOP
(157)
BODY FRAME
(60)
SUPPORT PLATE
(150)
POWER SWITCH
(164) FIGURE T
SWITCH PUSH-
OFF TIP (41)
LOCKING PIN
(153)

SKU 93762 For technical questions, please call 1-800-444-3353. Page 20
Blade into the workpiece. (See Fig-
ure T.)
10. WARNING! Keep hands and
ngers safely away from the cut-
ting area.
Slowly lower the Body Frame (60),11.
while it gradually feeds the Saw
Blade (82) into the workpiece. Do not
force the Bandsaw to remove mate-
rial faster than it is designed to cut.
(See Figure T.)
Never attempt to remove mate-12.
rial stuck in the moving parts of the
Bandsaw while it is plugged in and
running. Turn off the Bandsaw if the
workpiece is to be backed out of an
uncompleted cut.
IMPORTANT:13. When in the horizontal
cutting mode only, the Switch Push-
Off Tip (41) will automatically turn
the Power Switch (164) to its “OFF”
position and shut off the Bandsaw’s
Motor when the cut has been com-
pleted. (See Figure T.)
Once the cut is made, check to make14.
sure the Power Switch (164) is in its
“OFF” position. Then, unplug the
Power Cord Plug from its electrical
outlet. (See Figure T.)
Wait until the Saw Blade (82) comes to15.
a complete stop. Next, raise the Body
Frame (60) to its full vertical position,
making sure it locks in place by turn-
ing the Support Plate (150) to the right
until it rmly locks into the Body Frame.
Remove the workpiece from the Vise
assembly (138, 141) and scrap mate-
rial from the Machine Bed (142) of the
Bandsaw. Then, slowly lower the Body
Frame (60) to its horizontal position
and lock it in place with the Locking Pin
(115). (See Figure T.)