Central Pneumatic 98898 Installation manual

1/4” AIR HYDRAULIC RIVETER
Model 98898
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2008 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 08i

SKU 98898 For technical questions, please call 1-800-444-3353. Page 2
SPECIFICATIONS
Nose Pieces 1/4”, 3/16”, 5/32”, 1/8”
Operating Pressure 90-120 PSI
Air Consumption 4.5 CFM @ 90 PSI
Air Inlet 1/4”-18 NPT Female
Riveting Capacity 1/8” - 1/4”
Save this manual
You will need the manual for the safety warnings and cautions, assembly instruc-
tions, operating procedures, maintenance procedures, trouble shooting, parts list, and
diagram. Keep your invoice with this manual. Write the invoice number on the inside of
the front cover. Keep both this manual and your invoice in a safe, dry place for future
reference.
SAFETY WARNING & CAUTIONS
WARNING: When using pneumatic equipment, basic safety precautions should always be fol-
lowed to reduce the risk of personal injury and hazards due to over pressurization. READ ALL
INSTRUCTIONS BEFORE USING THIS TOOL!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly
lit locations. Don’t expose to rain. Keep work area well lit. Do not use electrically
powered air compressors in the presence of ammable gases or liquids.
3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not
let them handle machines, tools, or hoses.
4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry
location to inhibit rust. Always lock up tools and keep out of reach of children.
5. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. Do not use a tool for a purpose
for which it was not intended.
6. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught
in moving parts. Nonskid footwear is recommended. Wear restrictive hair covering
to contain long hair.
7. USE EYE AND EAR PROTECTION. Always wear ANSI approved impact safety
goggles when working. Wear an ANSI approved dust mask or respirator when
working around metal, wood, and chemical dusts and mists.
8. DO NOT ABUSE THE COMPRESSOR’S CORD. Do not yank compressor’s cord
to disconnect it from the receptacle. Do not carry tools by the cord.
9. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not
reach over or across running machines.
10. MAINTAIN TOOLS WITH CARE. Keep tools clean for better and safer perfor-
mance. Follow instructions for lubricating and changing accessories. Inspect hoses

SKU 98898 For technical questions, please call 1-800-444-3353. Page 3
for leaks prior to use. The handle must be kept clean, dry, and free from oil and
grease at all times.
11. AVOID UNINTENTIONAL STARTING. Do not carry any tool with your nger on the
trigger, whether it is connected to the compressor or not.
12. STAY ALERT. Watch what you are doing, use common sense. Do not operate any
tool when you are tired.
13. CHECK DAMAGED PARTS. Before using any tool, any part that appears dam-
aged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment and binding of moving parts;
any broken parts or mounting xtures; and any other condition that may affect
proper operation. Any part that is damaged should be properly repaired or replaced
by a qualied technician. Do not use the tool if any switch does not turn on and off
properly.
14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accesso-
ries intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
15. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS. Read warning labels on prescriptions to determine if your judgment or
reexes are impaired while taking drugs. If there is any doubt, do not operate the
tool.
16. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the
compressor.
17. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY.
Make sure that regulator is set at least 10 PSI lower than the lowest rated piece of
equipment you are using.
18. DO NOT POINT AT PEOPLE OR ANIMALS. Whether the Riveter is loaded or not,
do not point at anything but what you plan on riveting.
19. BE CAREFUL WHEN LOADING RIVETER. Do not point at yourself. Never hold
the Trigger when loading.
20. NEVER OPERATE WITHOUT THE SAFETY CAP IN PLACE.
21. COMPRESSED AIR ONLY. Never use combustible gas as a power source.
22. WARNING: The brass components of this product contain lead, a chemical known
to the State of California to cause birth defects (or other reproductive harm). (Cali-
fornia Health & Safety code § 25249.5, et seq.)
REV 08h

SKU 98898 For technical questions, please call 1-800-444-3353. Page 4
UNPACKING
When unpacking, check to make sure the following parts are included. All sizes
listed below are approximate. If any parts are missing or broken, please call Harbor
Freight Tools at: 1-800-444-3353. There should be one Air Hydraulic Riveter, two combi-
nation wrenches, an extra set of jaws, and a three Nose Pieces threaded into the base
of the riveter. A fourth Nose Piece comes installed in the Riveter.
SET UP
It is advisable to use an in-line oiler. If you are not using an in-line oiler, put a few
drops of pneumatic oil into the Air Inlet (35) prior to every operation.
To Install A Nosepiece:
1.
NOSEPIECE (1)
OUTER CYLINDER (2)
TRIGGER (25)
FIGURE B
RIVET
(not included)
The Riveter comes with a set of four Nosepieces (1). The sizes of the Nosepieces
are 1/4”, 1/8”, 5/32”, and 3/16” and must be matched with the size of the rivet pin
(1/4”, 1/8”, 5/32”, or 3/16”) you intend to use. (See Figure B.)
2. Use the accessory Spanner when changing Nosepieces (1). Also, use care when
unscrewing a Nosepiece as the spring action in the Outer Cylinder (2) will cause
the Nosepiece to “pop out”. (See Figure B.)
Note: Nosepieces are stored underneath the Base Cover (34).
REV 08j

SKU 98898 For technical questions, please call 1-800-444-3353. Page 5
OPERATION
1. Depending on the size of rivet pin used, attach the corresponding Nosepiece size
(1/4”, 1/8”, 5/32”, or 3/16”) with the accessory Spanner Wrench (36).
2. IMPORTANT: When drilling rivet holes in a workpiece, make sure to use the same
diameter drill bit as the outer diameter of rivet sleeve you will be using.
3. Turn on the air compressor, and set its regulator between 90-120 PSI.
Do not exceed 120 PSI.
4. Insert the pin (long, thin end) of a rivet fully into the Nosepiece (1). Insert the
sleeve (short, thick end) of the rivet through the pre-drilled hole in the workpiece.
Do not touch the Trigger (25) when you are inserting rivets.
5. Hold the Riveter rmly with both hands, and squeeze the Trigger (25) to activate
the Riveter. Repeat as necessary. Then, release pressure on the Trigger. See
Figure B.
6. When nished using the Riveter, turn off the air compressor. Squeeze the Trigger
(25) again to release any compressed air in the Riveter. Then, disconnect the air
hose from the tool.
REV 08j

SKU 98898 For technical questions, please call 1-800-444-3353. Page 6
INSPECTION, MAINTENANCE, AND CLEANING
WARNING! Always wear ANSI-approved safety impact goggles when per-
forming any inspection, maintenance, or cleaning procedures.
WARNING! Prior to performing any inspection, maintenance, or cleaning of the Riveter,
make sure to disconnect the air hose from the tool. Then, squeeze the Trigger (25)
again to release any compressed air in the Riveter.
1. To clean the exterior of the Riveter, wipe with a clean, damp cloth using a mild
detergent or mild solvent. Do not immerse the tool in liquids.
2. To clean and change the Jaws:
a. Unscrew and remove the Outer Cylinder (2), using the accessory Spanner.
b. Use the Spanner to unscrew and remove the Jaw Cylinder (7). Use care as there
is a Jaw Pusher Spring (6) behind the Jaw Cylinder (7) which may y out.
c. Remove the Jaws (4) from between the Jaw Cylinder (7).
d. If you are going to clean the Jaws (4), use a steel brush and mild solvent. Apply a
light coat of machine oil to the Jaws (4).
e.
3-WAY SPANNER WRENCH (36)
(THREADS)
JAW CYLINDER
(7)
FIGURE C
OUTER
CYLINDER
(2)
If you are going to replace the Jaws: Insert the new Jaws (4) into the Jaw Cylinder
(7). (See Figure C.)
f. When re-assembling the Jaw Cylinder (7), make sure the Jaw Pusher’s (5) head
lines up with the Jaws. (See Figure C.)
g. Check the distance from the head of the Jaw Cylinder (7) to the mounting threads
of the Outer Cylinder (2) using the gauge on the 3-Way Spanner Wrench. With
the gauge at a slight incline, the back of the gauge should rest on the beginning
of the Frame Head threads, while the front of the gauge should rest on the front
edge of the Jaw Carrier (3). If it does not, have a qualied service technician re-
pair the Riveter. (See Figure C.)

SKU 98898 For technical questions, please call 1-800-444-3353. Page 7
To Prime The Riveter:
Note: If the riveter’s performance declines, it may be due to insufcient hydraulic oil.
Rell the hydraulic oil using the procedure below.
WARNING! Make sure the Riveter is disconnected from its air supply hose prior to
performing any maintenance, service, or changing accessories.
1.
Air Cylinder (19)
Air Cylinder Lid (24)
Lock Nut (18)
Air Cylinder (19)
Piston Head (22)
Figure D
Remove the Base Cover (34) and unscrew the Air Cylinder Lid (24) from the
bottom of the Riveter. See Figure D.
2. Use a pair of pliers (not included) to remove the Piston Head (22) from the Air
Cylinder (19). See Figure D.
3. Hold the Air Cylinder (19) upside down, and pour in hydraulic oil (not included).
The ll level should only reach the top of the Frame.
4. Insert the Piston Assembly back into the Air Cylinder (19). See Figure D.
5. Use the Spanner to rmly screw the Air Cylinder Lid (24) back onto the Air Cylinder
(19). See Figure D.

SKU 98898 For technical questions, please call 1-800-444-3353. Page 8
TROUBLESHOOTING
Problem Possible Cause Likely Solution
Jaws slipping. Worn or damaged Jaws. Replace Jaws.
Jaws will not open. 1. Loose Nosepiece.
2. Dirty Jaws.
1. Tighten Nosepiece.
2. Clean Jaws.
Stroke is too short. 1. Rivet pin not properly
inserted into Riveter.
2. Low oil.
3. Rivet wrong size.
1. Make sure that Pin is fully inserted.
2. Prime Riveter.
3. Use proper rivet length.
Weak pulling action. 1. Low air pressure.
2. Broken/inadequate air
compressor.
1. Check regulator.
2. Have compressor serviced by a qualied
technician/upgrade to compressor of sufcient
capability.
Leaking air. 1. Poor hose connections.
2. Damaged O-Ring.
3. Dirty Air Valve or airline
inlet.
1. Reconnect using pipe thread seal tape.
2. Replace O-Ring.
3. Clean and lubricate with pneumatic tool oil.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIA-
GRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANU-
FACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DIS-
TRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND
NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.

SKU 98898 For technical questions, please call 1-800-444-3353. Page 9
Part Description
1A 1/4” Nosepiece
1B 3/16” Nosepiece
1C 5/32” Nosepiece
1D 1/8” Nosepiece
2 Outer Cylinder
3 Jaw Case
4 Jaws
5 Jaw Pusher
6 Jaw Pusher Spring
7 Jaw Cylinder
8 Case Lock Nut
9Principle Axis
10 Plastic Ring
11 Frame
12 Lead Axis
13 Plastic Ring
14 Restore Spring
15 Steel Ring
Part Description
16 Airtight Lid
17 Silencer
18 Lock Nut
19 Air Cylinder
20 Pole Piston
21 Cushion
22 Piston Head
23 Nut
24 Air Cylinder Lid
25 Trigger
26 Linker
27 Press Plank
28 Air Valve
29 Valve Spring
30 Copper Washer
31 Valve
32 Spring
33 Nut
Part Description
34 Base Cover
35 Air Inlet
36 3-Way Spanner
37 Multi-Function Wrench
B01 O-Ring
B02 O-Ring
B03 O-Ring
B04 O-Ring
B05 O-Ring
B06 Spring Pin
B07 Spring Pin
B08 Pin
B09 Spring Pin
B10 O-Ring
B11 O-Ring
B12 O-Ring
B13 O-Ring
B14 O-Ring
PARTS LIST
REV 08l

SKU 98898 For technical questions, please call 1-800-444-3353. Page 10
PARTS LIST AND ASSEMBLY DIAGRAM
(36)
C02
C01
16
15
B03
14
9
13
B02
11
B01
10
876543
2
1
25
B06
B07
26
27
28
B10
29
30
B13
23
22
B12
21
20
18
19
10
B04
B07
17
B09
B08
31
32
B11
33
B05
24
34
(37)
REV 08l