Cequent Draw-Tite CQT24938 User manual

Equipment Required:
Applications:
Years Make Models
2016-Current* Chevrolet Camaro
*Visit our website for the most up to date
information regarding application years and trim
levels.
Ratchet Torque
Wrench
Safety
Glasses Sockets
7 mm
15 mm Flat
Head Screw
Driver
DO NOT EXCEED LOWER OF TOWING VEHICLE
MANUFACTURER’S RATING OR:
Hitch Type Max Gross Trailer Weight Max Tongue Weight
Weight Carrying 2000 lb. (908 kg) 200 lb. (90.8 kg)
Weight Distributing X X
Representative Vehicle Photo
Installation Time: 50 min
The time listed above is the average time
for professional installers. If you do not
feel comfortable performing this
installation on your own or are in need of
assistance, please contact a professional
installer.
Hitch Illustration
Front of
Vehicle
Cequent™Performance Products, Inc.
6’’ Socket
Extension
Plastic
Trim Tools
Installation Instructions
PART NUMBERS: 24938, 77326,
CQT24938
Star
Driver
T15

1. Fascia removal –use 7 mm socket and T-15 stardriver to remove (10) bolts and (4) screws, 1 bolt each side is hidden behind the wheel well liner. see Figure 2.
2. Fascia removal –Gently remove the fascia and unplug wiring. Set bumper fascia aside.
3. Bumper beam removal –Use 15 mm socket to remove (8) flange nuts, attaching bumper to end panel, and then slide exhaust bracket off of the 2 lower studs then remove bumper beam, see Figure 3.
4. Hitch installation –raise the hitch and align the attachment holes on hitch with studs on the end panel. Raise the bumper beam and sandwich the hitch, re-align the exhaust bracket with the 2 lower studs.
see Figure 1. Reuse the flange nuts and loosely fasten them.
5. Tighten all fasteners with torque wrench to 53 Lb.-Ft. (72 N*M)
6. Reinstall the wiring, fasteners, fascia, in steps 1 and 2. (Trim center, inside, lower edge of fascia in area of the hitch if necessary.) The hitch is intentionally designed to be close to the fascia at the center.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
Rear
Figure 1
Installation Instructions
PART NUMBERS: 24938, 77326, CQT24938
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Always wear SAFETY GLASSES
when installing hitch
Bumper end
panel
Bumper
beam
Existing
flange nuts
Figure 2
Figure 3
Drawbar must be used in the
RISE position only.
(Sold separately)
Drawbar Kit: 3593

Fascia removal –use 7 mm socket and T-15 stardriver to remove (10) bolts and (4)
screws, 1 bolt each side is hidden behind the wheel well liner. see Figure 2.
Fascia removal –Gently remove the fascia and unplug wiring. Set bumper fascia aside.
Bumper beam removal –Use 15 mm socket to remove (8) flange nuts, attaching
bumper to end panel, and then slide exhaust bracket off of the 2 lower studs then
remove bumper beam, see Figure 3.
Hitch installation –raise the hitch and align the attachment holes on hitch with studs on
the end panel. Raise the bumper beam and sandwich the hitch, re-align the exhaust
bracket with the 2 lower studs. see Figure 1. Reuse the flange nuts and loosely fasten
them.

Tighten all fasteners with torque wrench to 53 Lb.-Ft. (72 N*M) Reinstall the wiring, fasteners, fascia, in steps 1 and 2. (Trim center, inside, lower edge
of fascia in area of the hitch if necessary.) The hitch is intentionally designed to be
close to the fascia at the center.
Proper torque is needed to keep the hitch secure to the vehicle when towing.