Chamberlain MyQ Garage User manual

MyQ Garage
TM
Universal Smartphone
Garage Door Controller
USER’S GUIDE
(affix serial number label)
Serial Number

2
To reduce the risk of SEVERE INJURY to persons:
• DO NOT enable the Chamberlain Universal Smartphone Garage Door Controller if
operating either one-piece or swinging doors. To be enabled ONLY on a sectional
door.
Read instructions thoroughly BEFORE beginning.
If using this product with residential door openers, this product
must be used only with door openers manufactured after 1993 that
utilize photoelectric sensors. The photoelectric sensors are always
located on or near the bottom of the door track.
STOP
WHAT'S IN THE BOX
Wi-Fi Hub
Door Sensor
Power Supply
Hardware for Wi-Fi Hub
(5/32", long screws)
Bracket for Wi-Fi Hub
Hardware for Door Sensor
(5/32", short screws)
Fastening Strips for
Door Sensor User’s Guide Warning Placard
NOTE: The Wi-Fi hub can control up to 2 garage doors, however an additional door
sensor is required. Follow the instructions included with the new door sensor for
programming instructions.

3
BEFORE STARTING YOU MUST HAVE...
• A mobile device, used during setup
• Router with Wi-Fi®
• Broadband Internet Connection
• Wi-Fi Hub Serial Number (located in this User's Guide and on the Wi-Fi Hub)
• Compatible Garage Door Opener (www.chamberlain.com/MyQGarage)
• Make sure your mobile device is connected to the Wi-Fi network.
• Make sure there is a strong Wi-Fi®signal in the garage where the Wi-Fi Hub will
be mounted. To verify, place your mobile device in the location where the Wi-Fi
Hub will be installed. You mobile device should display two or more bars. If not,
move the router closer to the garage or purchase a Wi-Fi range extender (refer to
the Help section of this User's Guide).
Wi-Fi Hub
Door Sensor
The LEDs are visible
when directly facing
the Wi-Fi Hub.
Light
Blue LED
Green LED
Yellow LED
LED
Test Button

4
MyQ
Wi-Fi
Home
MyQ
Bluetooth Devices
My Car
i
i
Blue LED
OR
Select MyQ
1CONNECT TO NETWORK
Make sure the Wi-Fi signal in the garage is strong and your mobile device is
connected to your home Wi-Fi network.
Connect with mobile device
1. Plug in the Wi-Fi Hub. The blue LED will blink, the Wi-Fi Hub is ready to be
connected to your home Wi-Fi network.
2a. iPhone®or iPod touch®*: Go to Settings > Bluetooth®and turn on Bluetooth.
Select the Bluetooth device with the "MyQ" prefix. Click "Allow" to share Wi-Fi
settings then proceed to App store to download MyQ App.
OR
2b. All other mobile devices: Go to settings, select Wi-Fi, then select the network with
the “MyQ” prefix and select connect. Once connected, launch the mobile device's
web browser and go to "setup.myqdevice.com". Follow the on-screen instructions
to connect to your home network and download the App.
NOTE: Do not operate the garage door opener until installation has been completed.
3. If the green LED is glowing solid, proceed to step 2 Installation. If the green LED is
not glowing solid, repeat the steps above or proceed to Alternate Method: Connect
with WPS (Wi-Fi Protected Setup).
*Made for:
iPhone 3GS, iPhone 4, iPhone 4S, and iPhone 5
iPod touch (4th and 5th generation)

5
ALTERNATE METHOD: Connect with WPS (Wi-Fi Protected Setup)
If your router is using WEP security setting, change it to WPA or WPA2.
1. Plug in the Wi-Fi Hub. The blue LED will blink, the Wi-Fi Hub is ready to be
connected.
2. Press and release the BUTTON on the Wi-Fi Hub. The blue LED will turn solid.
3. Press the router’s WPS button to activate WPS mode. It may take a few minutes for
the Wi-Fi Hub to connect to the router. The Wi-Fi Hub’s green LED will turn solid
when the Wi-Fi Hub is connected to your network.
4. Download the Chamberlain MyQ®Home Control App from the App Store or Google
Play. NOTE: Do not operate the garage door opener until installation has been
completed.
5. If the green LED is glowing solid, proceed to step 2 Installation.
Blue LED
WPS Mode
BUTTON