ChargePoint CP6000 Series User manual

ChargePoint ® CP6000 Series — Fleet
Specifications and Ordering Information
Dual port, pedestal mount, 23 ft cable

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20222 of 8
Ordering Information
The order codes below represent specific product configurations. Please contact ChargePoint Sales for
additional information.
Specify model number followed by the applicable code(s).
The order code sequence is: Model-Options. Software, Services and Other are ordered as separate line
items.
Hardware
Description Order Code
Model
80A Dual port, pedestal mount, 23 ft cable
CP6021X-80A-L7
80A Single port, pedestal mount, 23 ft cable
CP6011X-80A-L7
80A Dual port, wall mount, 23 ft cable
CP6023X-80A-L7
80A Single port, wall mount, 23 ft cable
CP6013X-80A-L7
Other
Bollard Concrete Mounting Kit
CP6K-CMT-NA
Software and Services
Description
Order Code
ChargePoint Power Plan
CPCLD-POWER-n*
ChargePoint Enterprise Plan
CPCLD-FLEETENT-
n*
ChargePoint Fleet Commercial CPCLD-FLEETCOMM-n*
ChargePoint Assure CP6000-ASSURE-n*
Station Activation and Configuration CPSUPPORT-ACTIVE
ChargePoint Site Validation
CPSUPPORT-SITEVALID
ChargePoint Installation and Validation CP6000-INSTALLVALID
Note: All CP6000 stations require a network service plan per port.
*Substitute n for desired years (1, 2, 3, 4 or 5 years)

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20223 of 8
Architectural Drawings and Dimensions
Pedestal Mount

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20224 of 8
Wall Mount

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20225 of 8
General Specifications
Electrical Input
The CP6000 supports flexible wiring and power settings up to 80A. Power Select allows stations to be
installed and configured for current lower than the maximum 80A. Power Select current options include 40A,
48A, 56A, and 64A.
Power Share allows a dual-port station to share power from a single circuit across two ports, adjusting
power depending on whether one or both are charging. Standard wiring uses an independent circuit for each
port. Power Share can be used in combination with Power Select.
Electrical Input
Single Port
(AC Voltage 208 / 240V AC)
Dual Port
(AC Voltage 208 / 240V AC)
Input
Current
Input Power
Connection
Required
Service
Panel
Breaker
Input
Current
Input Power
Connection
Required
Service Panel
Breaker
Maximum 80A (Standard) 80A
One 100A
branch
circuit
100A dual
pole (non-
GFCI)
80A x 2
Two
independent
100A branch
circuits
100A dual
pole (non
GFCI) x 2
Maximum 80A (Power Share*) N/A N/A N/A 80A One 100A
branch circuit
100A dual
pole (non
GFCI)
Power Select** 40A - 64A
(Standard)
40A -
64A
One branch
circuit rated
125% of
input
current
(50A - 80A)
Dual pole
(non-GFCI)
rated 125%
of input
current
(50A-80A)
40A -
64A x 2
Two
independent
branch
circuits rated
125% of input
current (50A -
80A)
Dual pole
(non-GFCI)
rated 125% of
input current x
2
Power Select 40A - 64A
(Power Share) N/A N/A N/A 40A - 64A
One branch
circuit rated
125% of input
current (50A -
80A)
Dual pole
(non-GFCI)
rated 125% of
input current
(50A - 80A)
Service Panel/Breaker GFCI Do not provide external GFCI as it may conflict with internal GFCI (CCID)
Wiring – Standard
3-wire (L1, L2, Earth)
No neutral
5-wire (L1, L1, L2, L2, Earth)
Wiring – Power Share N/A 3-wire (L1, L2, Earth)
Line to Ground Voltage 120V +/- 10%

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20226 of 8
Electrical Output
Electrical Output
Single Port
(AC Voltage 208 / 240V AC)
Dual Port
(AC Voltage 208 / 240V AC)
Maximum 80A (Standard)
19.2 kW (240V AC @ 80A)
19.2 kW (240V AC @ 80A)
Maximum 80A (Power Share)
N/A
19.2 kW (240V AC @ 80A) x 1
or
9.6 kW (240V AC @ 40A) x 2
Power Select 40A - 64A
(Standard)
9.6 kW – 15.4 kW (240V AC
@ 40A - 64A)
9.6 kW - 15.4 kW (240V AC @ 40A - 64A) x
2
Power Select 40A - 64A
(Power Share)
N/A
9.6 kW - 15.4 kW (240V AC @ 40A - 64A) x
1
or
4.8 kW – 7.7 kW (240V AC @ 20A - 32A) x
2
Mounting and Functional Interfaces
Connector Type SAE J1772TM
Number of Ports
Single, dual
Mounting Pedestal, wall
Cable Length 23 ft (7 m)
Cable Management Yes
Authentication
RFID: ISO 15693, ISO 14443, NEMA EVSE 1.2-2015 (UR)
NFC (Tap to Charge)
Remote: mobile and in vehicle (if supported by vehicle)
Locking Holster Yes
ISO 15118 Supported by hardware
Safety and Connectivity Features
Ground Fault Detection
20 mA CCID with auto retry
Open Safety Ground
Detection Continuously monitors presence of safety (green wire) ground connection
Plug-Out Detection Power terminated per SAE J1772TM specifications

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20227 of 8
Power Measurement
Accuracy +/- 2% from 2% to full scale
Power Report/Store Interval
15-minute interval aligned to hour. Responsive to load management signals.
Local Area Network
Wi-Fi 2.4 GHz and 5GHz (802.11 a/n/b/g)
Wide Area Network
LTE Category 4
Network Communication
Protocol OCPP 2.0.1
Ethernet connection
Capable with accessory
Safety and Operational Ratings
Station Enclosure Rating Type 3R
Station Surge Protection
6 kV @ 3,000A. In geographic areas subject to frequent thunderstorms,
supplemental surge protection at the service panel is recommended.
EMC Compliance FCC Part 15 Class B
Operating Temperature -40°C to 50°C (-40°F to 122°F)
Non-Operating Temperature -40°C to 60°C (-40°F to 140°F)
Terminal Block Temperature
Rating 105°C (221°F)
Operating Humidity Up to 85% @ 50°C (122°F) non-condensing
Non-Operating Humidity Up to 95% @ 50°C (122°F) non-condensing

ChargePoint ® CP6000 Series — Fleet
ChargePoint, Inc. | Copyright © 20228 of 8
ChargePoint, Inc.
240 East Hacienda Avenue
Campbell, CA 95008-6617 USA
Contact Us
Visit chargepoint.com
ChargePoint, Inc. (“ChargePoint”) reserves the right to alter product offerings and specifications at any time without notice.
ChargePoint is not responsible, and disclaims any and all liability, for typographical or graphical errors, inaccuracies, or
incompleteness that may appear in this document. This document does not expand or otherwise modify ChargePoint’s terms
and conditions of purchase, including but not limited to the warranty expressed therein.
Copyright © 2022 ChargePoint, Inc. All rights reserved. CHARGEPOINT is a U.S. registered trademark/service mark, and
an EU registered logo mark of ChargePoint, Inc. ASSURE and CHARGEPOINT AS A SERVICE are U.S. registered
trademarks of ChargePoint Inc. All other products or services mentioned are the trademarks, service marks, registered
trademarks or registered service marks of their respective owners

Installation Guide
ChargePoint CP6000 Series
Networked Charging Station

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING:
1. Read and follow all warnings and instructions before servicing, installing, or operating
the ChargePoint® charging station. Install and operate only as instructed. Failure to do so
may lead to death, injury, or property damage, and will void the Limited Warranty.
2. Only use licensed professionals to install your ChargePoint charging station and adhere
to all national and local building codes and standards. Before installing the ChargePoint
charging station, consult with a licensed contractor, such as a licensed electrician, and use
a trained installation expert to ensure compliance with local building and electrical codes
and standards, climate conditions, safety standards, and all applicable codes and
ordinances. Inspect the charging station for proper installation before use.
3. Always ground the ChargePoint charging station. Failure to ground the charging station
can lead to risk of electrocution or fire. The charging station must be connected to a
grounded, metal, permanent wiring system, or an equipment grounding conductor shall be
run with circuit conductors and connected to the equipment grounding terminal or lead on
the Electric Vehicle Supply Equipment (EVSE). Connections to the EVSE shall comply with
all applicable codes and ordinances.
4. Install the ChargePoint charging station on a concrete pad using a ChargePoint-
approved method. Failure to install on a surface that can support the full weight of the
charging station can result in death, personal injury, or property damage. Inspect the
charging station for proper installation before use.
5. This charging station is not suitable for use in Class 1 hazardous locations, such as near
flammable, explosive, or combustible vapors or gases.
6. Supervise children near this device.
7. Do not put fingers into the electric vehicle connector.
8. Do not use this product if any cable is frayed, has broken insulation, or shows any other
signs of damage.
9. Do not use this product if the enclosure or the electric vehicle connector is broken,
cracked, open, or shows any other signs of damage.
10. Use only copper conductor wire rated for 90 °C (194 °F).
IMPORTANT: Under no circumstances will compliance with the information in a ChargePoint
guide such as this one relieve the user of the responsibility to comply with all applicable codes
and safety standards. This document describes approved procedures. If it is not possible to
perform the procedures as indicated, contact ChargePoint. ChargePoint is not responsible for
any damages that may result from custom installations or procedures not described in this
document or that fail to adhere to ChargePoint recommendations.
ii

Product Disposal
Do not dispose of as part of unsorted domestic waste. Inquire with local authorities
regarding proper disposal. Product materials are recyclable as marked.
Document Accuracy
The specifications and other information in this document were verified to be accurate
and complete at the time of its publication. However, due to ongoing product
improvement, this information is subject to change at any time without prior notice. For
the latest information, see our documentation online at chargepoint.com/guides.
Copyright and Trademarks
©2013-2023 ChargePoint, Inc. All rights reserved. This material is protected by the copyright laws of the
United States and other countries. It may not be modified, reproduced, or distributed without the prior,
express written consent of ChargePoint, Inc. CHARGEPOINT is a US, UK, and EU registered trademark and
service mark of ChargePoint, Inc. and cannot be used without the prior written consent of ChargePoint.
Symbols
This guide and product use the following symbols:
DANGER: Risk of electric shock
WARNING: Risk of personal harm or death
CAUTION: Risk of equipment or property damage
IMPORTANT: Crucial step for installation success
Read the manual for instructions
Ground/protective earth
Illustrations Used in This Document
The illustrations used in this document are for demonstration purposes only and may not be an exact
representation of the product. However, unless otherwise specified, the underlying instructions are
accurate for the product.
iii

iv

IMPORTANT SAFETY INSTRUCTIONS ii
1 Introduction 1
Accessing Complete Documentation 2
Power Management 2
Site Requirements 2
Bring These Tools and Materials 3
Inspect the Boxes for Contents 4
2 Install a Pedestal Mount 5
Prepare the Pedestal for Mounting 5
Mount the Pedestal 7
Install the Housing 12
Install the CMK 17
3 Install a Wall Mount 25
Mount the Brackets 25
Mount the CMK 28
Prepare the Housing 33
Install the Housing 36
Install the Conduit 38
4 Connect Wiring - North America 39
Grounding Requirements 39
Install Circuit Sharing Jumpers 42
Install the Power Plate 43
Connect the Wiring 44
Check Voltages 52
5 Assemble the Station 53
Connect the Head Assembly 53
Install Cable Clamps 64
v
Contents

6 Complete Station Setup 69
Power Up 69
Configure and Pinpoint the Station 72
Start a Charging Session 75
Questions? 75
vi

1Introduction 1
The ChargePoint CP6000 is an all-purpose charging station for property owners, businesses, and
municipalities. It can be mounted on a pedestal or a wall.
CP6000 charging stations are alternating current (AC) supply equipment. Once they are installed and
activated, they are connected to the AC network.
Note: CP6000 charging stations do not have ventilation capabilities.
IMPORTANT: You must be a licensed electrician and complete online training to become a
ChargePoint certified installer. If you do not complete training, you cannot access the
ChargePoint network to complete installation.
Find online training at: chargepoint.com/installers
If the charging station is not installed by a ChargePoint certified installer, using a ChargePoint
approved method, it is not covered under warranty and ChargePoint is not responsible for any
malfunctions.
Note: CP6000 charging stations are available in several configurations. The images in this guide might not
match your station exactly; however, the installation steps are the same unless otherwise noted.
1

Accessing Complete Documentation
Access ChargePoint documents at chargepoint.com/guides.
Document Content Primary Audiences
Datasheet Full station specifications Site designer, installer, and
station owner
Site Design Guide Civil, mechanical, and electrical
guidelines to scope and construct
the site
Site designer or engineer of
record
Concrete Mounting Template
Guide
Instructions to embed the charging
station template in a concrete pad
with anchor bolts and conduit
placement
Site construction contractor
Construction Signoff Form Checklists used by contractors to
ensure the site is correctly
completed and ready for product
installation
Site construction contractor
Installation Guide Anchoring, wiring, and powering on Installer
Operation and Maintenance
Guide
Operation and preventive
maintenance information
Station owner, facility manager,
and technician
Service Guide Component replacement
procedures, including optional
components
Service technician
Declaration of Conformity Statement of conformity with
directives
Purchasers and public
Power Management
Using ChargePoint Power Management technology, sites can install more stations than would otherwise be
supported by the available electrical service. A maximum aggregate load is defined for a group of charging
stations. ChargePoint cloud-based services manage the individual power output of each station (or port)
to ensure the maximum load is never exceeded.
A CP6000 charging station provides up to 80 A of output current to each charging port.
Site Requirements
Ensure that the appropriate wiring, circuit protection, and metering are in place at the installation location
by reviewing the Site Design Guide and the Datasheet, as well as the wiring diagrams and grounding
requirements in the Connect Wiring chapter.
IMPORTANT: Ensure the installation complies with all applicable codes and ordinances.
2

Bring These Tools and Materials
To install CP6000 charging stations, you need the following tools:
L wrench - Torx end (T25)
included, combined with 4 mm hex
L wrench - Hex end (4 mm)
included, combined with T25 Torx
Mini-ratchet wrench Torx screwdriver (T25)
Adjustable torque wrench
nut size 4 mm and 24 mm 8 mm hex wrench
Wire stripper Level
Multimeter
(solenoid type voltmeter preferred) Diagonal wire cutter
CMK ball removal (included) #3 Philips screwdriver
Drill and tap for appropriate wall
attachment hardware
(wall mount stations only)
10 mm socket
Protective cut-proof gloves
Wall mounting hardware requirements vary based on surfaces:
lMasonry anchors rated for at least 318 kg (700 lb) of pull-out force.
lAttachment hardware appropriate for mounting surface. For example, use
10 x 75 mm (3/8 x 3 in) lag bolts if mounting on a wooden wall.
3
Bring These Tools and Materials

Inspect the Boxes for Contents
The CP6000 ships in multiple boxes. Check to make sure you have all of the following parts before
beginning work.
a. Cable Management Kit (CMK)
b. Top cap
c. Pedestal or wall mount enclosure
d. Head unit assembly
e. Smart EV cables
f. Mounting adapter (only wall mount stations)
g. Circuit share jumper kit
h. Quick Reference Guide, rating labels
IMPORTANT:
If a single supply circuit is feeding a dual port station, you MUST install power management
jumpers for both ports to operate correctly. Contact ChargePoint Support to order power
management jumpers if required.
4

2Install a Pedestal Mount 2
Prepare the Pedestal for Mounting
1. Lift the power plate cover. Loosen, but do not remove, two screws.
5

2. Remove the power plate and set it gently on a padded surface.
3. Use the L-wrench or mini-rachet wrench to loosen, but not remove, two screws.
6