Chatsworth Products ELS1500 User manual

REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK
IIS-739227, 02/18/13, Rev. 1, CPI/
800-834-4969 (USA & Canada) • www.chatsworth.com • [email protected]
For international phone numbers, see our website or contact CPI Tech Support.
This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing
or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
Page 1 of 5
Installation Instructions
Included Hardware:
ELS1000 Master Kit:
M4X12mm screw 1 ea.
M4 Washer, 1 ea.
M10 Washer, 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
ELS1000 latch box contains a set of standard fasteners, please select the items
shown below from the box:
M4X10mm Flanged Screw: 1 ea. M16 Nut: 1 ea.
ELS1500 Master Kit:
M10 washer, 1 ea.
M5X16mm screw, 2 ea.
M6X35mm Hex screw, 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
Please select the spindle below from the ELS1500 latch box:
Tools Required:
#2 Philips screw driver.
19 mm Wrench
Rivet gun
Installation Notes:
•The cabinet door must be disassembled in order to install or remove a
two-point latch, because the lock rods extend beyond the top and
bottom of the door.
ELS1000 Assembly Sequence
1. Install the two point ELS1000 (Fig. 1) onto rear solid door.
M10 Washer
E-ring
Front plate Border
ELS1000
ELS1000
Rear plate
ELS1000
Lock rod
M4 X 12mm
screw
Clevis pin
Cam
M16 nut
Fig. 1
ELS1000 Lock
M4 Washer
M4 X 10mm
screw
flanged
0.787” (20 mm)

REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK
Page 2 of 5
Installation Instructions
2. Install lock rod guide brackets on top and bottom of rear door. Do not
insert the lock rods yet (Fig. 2).
3. Position the ELS1000 lock with spindle orientation up and Front plate
on the door over the latch cut-out and fasten with Rear plate using
M4X12mm screws and M4 washer (Fig. 2).
4. Place the M16 Nut over the lock barrel and tighten it (Fig. 2).
5. Fasten the cam into the Lock barrel with M4X10mm flanged screws &
M10 Washer (Fig. 3).
M4 X 10mm
flanged screw
M10 Washer
Rear plate
Cam
Fig. 3
ELS1000 Lock
Back side view
Door back side
Lock rod
Guide Bracket
M4 Washer
M4 X 12mm
Screw
Fig. 2
ELS1000 lock
Installation
Rear plate
ELS1000
M16 Nut
ELS1000 Lock

REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK
Page 3 of 5
Installation Instructions
6. Insert the lock rods through the guides, with the short rod on the top
and the long rod on the bottom (Fig. 4).
7. Insert the cam assembly pins through the short rod (on top) and the
long rod (on bottom), then through the other half of the cam assembly
(Fig. 4) and locked with-ring.
Lock rod
Lock rod
Guide
Clevis Pin
E-ring
Fig. 4
ELS1000
Lock Rod Installation

REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK
Page 4 of 5
Installation Instructions
ELS1500 Assembly Sequence
1. Install the two point ELS1500 (Fig. 5) onto rear solid door.
2. Install lock rod guide brackets on top and bottom of rear door. Do not
insert the lock rods yet (Fig. 6).
3. Position the ELS1500 lock with spindle orientation up and Front plate
on the door over the latch cut-out and fasten with Rear plate using
M5X16mm screws (Fig. 6).
4. Insert the lock rods through the guides, with the short rod on the top
and the long rod on the bottom (Fig. 7).
Fig. 5
KL 1500 Lock
Front plate Border
ELS1500
ELS1500
Rear plate
ELS1500
Cam
Lock rod
Clevis pin
M6 X 35mm
Hex screw
M5 X 16mm
screw
M10 washer
E-ring
M5 X 16mm
Screw
Lock rod
Guide Bracket
Rear plate
ELS1500
ELS1500 Lock
Fig. 6
ELS1500 lock
Installation
M5 X 16mm
Screw
KL1500 Lock

REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK
Page 5 of 5
Installation Instructions
5. Insert the cam assembly pins through the short rod (on top) and the
long rod (on bottom), then through the other half of the cam assembly
(Fig. 7) and locked with-ring.
Lock rod
Lock rod
Guide
Clevis Pin
E-ring
Fig. 7
ELS1500
Lock Rod Installation