Chauvet ART-1CON User manual

CHAUVET, 3000 N 29th CT, Hollywood, FL 33020 U.S.A.
phone [phone] fax [phone]
ART-1CON User Manual
ART-1CON Spectrum Controller™
The ART-1CON is a user friendly dedicated controller for the Spectrum™ Architectural Exterior Wash.
It allows the user to select manually any one of 10 colors on buttons or any of the 15 available
colors using the slider including the color scroll effect. The controller can be set to hold any
particular color or the timed-chase can be modified between .01 seconds and 10 minutes. There are
10 built in chase patterns to choose from. Unless you intend to hold a color for a full day, to extend
the time period beyond 10 minutes use a universal DMX controller. Visit www.chauvetlighting.com
and browse the section under DMX Controllers.
Addressing fixtures remotely using the ART-1CON
1. Hold down the BLACKOUT button for 3 seconds.
2. Use the Color/Number buttons to enter the number of fixtures you have daisy chained. Up to 3 digits
can be entered
3. Upon releasing, the fixtures will be automatically addressed by the controller.
Fixture reset 1. Hold down the BLACKOUT button for 3 seconds.
2. Use the HOLD button to reset all fixtures.
Color/Number Buttons
These buttons are not only
used for the selection of a
color or chase patterns but
as a numerical keypad
when remote addressing
fixtures.
Blackout
Temporarily
eliminated light
output from the
fixture.
Chase
Pressing this buttons enables the pattern chase select using the Color/Numbers
buttons. The following 3 chase modes can also be set:
One way (LED On); color changes occur in one direction
Example: color 1,2,3,4,5 etc. color 1,2,3,4,5 etc.
Loop (LED blinks fast); color changes in forwards then reverse order
Example: color 1,2,3,4,5 ~ etc. ~ 5,4,3,2,1
Manual (LED blinks slowly); you can manually step through the scenes in a program
Example: press any one program button repeatedly to advance to the next step within
the program until the desired look is achieved.
Speed & Color Slider
When Chase button is activated, use
this slider to adjust the chase speed
from .01 to 10 minutes. When in Hold
use to access all colors available on the
Spectrum, including a color scroll.
Hold
Enables the color
selection aspect
of the
Color/Numbers
buttons
QUICK OVERVIEW
Rear of controller
Power Switch
Power Adapter Input
DMX
-
512 signal output

CHAUVET, 3000 N 29th CT, Hollywood, FL 33020 U.S.A.
phone [phone] fax [phone]
ART-1CON User Manual
Chase patterns described
Chase Patterns Chase Pattern Description
1Changes colors at random
2Group changing colors – one by one
3Group changing colors – two by two
4Group changing colors – four by four
5Group changing colors – eight by eight
6Group changing colors – 16 by 16
7Color chasing – one fixture after another in sequence
8Color chasing – 2 after 2 in sequence
9Color chasing – 4 after 4 in sequence
0Color chasing – 8 after 8 in sequence
Color List Used in Chase Programs Available using buttons
1Cyan 1 White
2White 2 Red
3Red 3 Orange
4Yellow 4 Yellow
5Blue 5 Amber
6Green 6 Green
7Light Yellow 7 Cyan
8Light Blue 8 Blue
9Light Green 9 Purple
10 Purple 0 Pink
11 Orange
12 Pink
Chase modes described
MODE LED Status Description of color change/chase programs Notes
One Way Permanently ON Color sequence:
1,2,3,4,5,6,7,8,9,10,11,12 --1,2,3,4,5,6,7,8,9,10, etc……
Refer to the Color List
for color reference
information.
Loop Blinks fast Color sequence:
1,2,3,4,5,6,7,8,9,10,11,12 -- 12,11,10,9,8,7,6,5, etc…
Manual Blinks slowly
You will manually step through each color change using the
same button of the chase pattern program selected. You
are also able to hold that color combination.
1. Press CHASE button until the LED blinks slowly
2. Select any one of the Color/Number buttons to
select the pattern chase as described in the table
above.
3. Select the same Color/Number button to step
through the color sequence until you arrive at a
combination of your liking.
4. Leave it there, do nothing else to hold.
Refer to the table
above for chase
pattern description.
ART-1CON Specifications
Shipping: 5.5 in (139.7mm) x 8 in (203.2mm) x 3.5 in (88.9mm)
Weight: 2 lbs (0.91Kgs)
Master Packed: 10 pcs / 30.86lbs (14.0Kgs)
Power Adapter: Input AC120V or AC230V 50/60Hz, Output DC 9V 50mA
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (USA)
Support Email: [e-mail]
Tel: [phone] Press 4
Fax: (954) 929
-
5560 Attentio
nService