Chauvet The Intimidator Scan LED 200 User manual

User Manual

CHAUVET®, 2010, All Rights Reserved
Information and specifications in this User Manual are subject to change without notice.
CHAUVET® assumes no responsibility or liability for any errors or inaccuracies that may appear
in this manual.
Author: Anthony Chiappone
Revision: 01B
Release Date: 10-11-2010
TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
MANUAL CONVENTIONS.........................................................................................................................................................................3
ICONS ..................................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 5
PRODUCT DIMENSIONS..........................................................................................................................................................................5
PRODUCT OVERVIEW ............................................................................................................................................................................6
3. SETUP............................................................................................................................................................................... 7
ACPOWER...........................................................................................................................................................................................7
Power Linking...........................................................................................................................................................................................................7
MOUNTING ...........................................................................................................................................................................................8
Orientation................................................................................................................................................................................................................8
Rigging.....................................................................................................................................................................................................................8
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 9
USING THE CONTROL PANEL..................................................................................................................................................................9
MENU MAP...........................................................................................................................................................................................9
CONFIGURING THE STARTING ADDRESS..................................................................................................................................................9
OPERATION........................................................................................................................................................................................10
DMX Operation......................................................................................................................................................................................................10
Master/Slave Mode (Sound-Active, Auto Mode)...................................................................................................................................................10
Automatic-Slow......................................................................................................................................................................................................10
Automatic-Fast.......................................................................................................................................................................................................10
Sound-Active..........................................................................................................................................................................................................11
SERVICE MODE...................................................................................................................................................................................11
Hidden Menu Map..................................................................................................................................................................................................11
DMXCHANNEL VALUES ......................................................................................................................................................................12
8-CH Mode.............................................................................................................................................................................................................12
5-CH Mode.............................................................................................................................................................................................................13
5. APPENDIX....................................................................................................................................................................... 14
GENERAL TROUBLESHOOTING..............................................................................................................................................................14
DMXPRIMER .....................................................................................................................................................................................15
FIXTURE LINKING (DAISY CHAIN)..........................................................................................................................................................15
DATA CABLING....................................................................................................................................................................................15
DMX Data Cable....................................................................................................................................................................................................15
CABLE CONNECTORS ..........................................................................................................................................................................16
SETTING THE STARTING ADDRESS........................................................................................................................................................16
3-Pin to 5-Pin Conversion Chart............................................................................................................................................................................17
Setting up a DMX Daisy Chain..............................................................................................................................................................................17
GENERAL MAINTENANCE .....................................................................................................................................................................18
RETURNS PROCEDURE........................................................................................................................................................................18
CLAIMS ..............................................................................................................................................................................................18
TECHNICAL SPECIFICATIONS......................................................................................................................................... 18
CONTACT US ..................................................................................................................................................................... 19

1. Before You Begin 3 12/9/2010 10:32 AM
1.BEFORE YOU BEGIN
What is included
•1 x Intimidator™ Scan LED 200
•1 x Mounting bracket kit
•1 x Power Cord
•1 x Warranty Card
•1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure
that all parts are present, and have been received in good condition. Notify the shipper
immediately and retain packing material for inspection if any parts appear damaged from
shipping or the carton itself shows signs of mishandling. Save the carton and all packing
materials. In the event that a fixture must be returned to the factory, it is important that the fixture
be returned in the original factory box and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information
from the regular text.
C
ONVENTION M
EANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the fixture’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating
mode/current status)
MENU >
Settings A sequence of menu options to be followed
ON A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special attention on the
part of the user.
I
CONS M
EANING
This paragraph contains critical installation, configuration or operation
information. Failure to comply with this information may render the fixture
partially or completely inoperative, cause damage to the fixture or cause
harm to the user.
This paragraph contains important installation or configuration information.
Failure to comply with this information may prevent the fixture from
functioning correctly.
This paragraph reminds you of useful, although not critical, information.

1. Before You Begin 4 12/9/2010 10:32 AM
Safety Instructions
•Please keep this User Manual for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line
voltage you are connecting to is not higher than that stated on the decal or rear panel
of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not
expose fixture to rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm)
from adjacent surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to
replace with same fuse source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at
temperatures higher than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry the fixture directly from the cord. Always use the hanging/mounting
bracket.
•Avoid direct eye exposure to the light source while it is on.
Please read these instructions carefully. It includes important information
about the installation, usa
g
e and maintenance of this
p
roduct.

2. Introduction 5 12/9/2010 10:32 AM
2.INTRODUCTION
Product Dimensions

2. Introduction 6 12/9/2010 10:32 AM
Product Overview
Power Out
DMX In
DMX Out Power In
Microphone
Fuseholde
r

3. Setup 7 12/9/2010 10:32 AM
3.SETUP
AC Power
This fixture is auto-ranging and runs on 100~240 VAC, 50/60 Hz power.
To determine the power requirements for a particular fixture, see the label affixed to the back
plate of the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating
indicates its average current draw under normal conditions.
Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only
as a 0 to 100% switch.
Always connect the fixture to a circuit with a suitable electrical ground.
Power Linking
This fixture contains power linking via the Edison outlet located in front of the power input cable.
Please see the diagram below for further explanation.
The maximum quantity of Intimidator™ Scan LED 200 that may be linked is 8.
The power linking shown in this document is for the CHAUVET® North American version
ONLY! Therefore, it is the customer’s responsibility to check with the Dealer/Distributor
regarding power linking on the local version of the product. Connections and availability
may change, depending on the power requirements and/or regulations of each
country/region.
Additional power
link out
Fixture #1 Fixture #2 Fixture #3

3. Setup 8 12/9/2010 10:32 AM
Mounting
Orientation
The Intimidator™ Scan LED 200
may be mounted in any position provided there is adequate
room for ventilation.
Rigging
Be sure that the structure can support the weight of the fixture. Please see the “Technical
Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This
may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm
in size. When rigging, consider routine maintenance and control panel access. Please see the
following notes on installation.
•If the power link out is intended to be used with multiple fixture, take into account the
length of each power cable, and mount the fixtures close enough to one another to
accommodate for this.
•When aiming the fixtures, you may use the bracket/yoke adjustment knob(s). Loosen
the knob(s), adjust to the desired angle, and then tighten the knob(s) by turning
clockwise. Do not use tools for this step, as it may cause damage.
•Use the secondary portion of the hanging bracket to support the fixture in a sitting
position. Please see the diagram below.
•Safety cables must always be used.
In the diagram above, the secondary portion of the hanging bracket is being used as a
ground support.
Hanging Bracket
Bracket Adjustment
Knob
Bracket Adjustment
Knob
Safety
Sitting position

4. Operating Instructions 9 12/9/2010 10:32 AM
4.OPERATING INSTRUCTIONS
Using the Control Panel
Access control panel functions using the four buttons located directly underneath the LED display on
the included wired remote.
BUTTON FUNCTION
<MODE/
ESC>
Used to scroll through the current
operating mode, as well as back
out of the current menu option
<DOWN> Used to select decreasing
advancement in the value
<UP> Used to select increasing
advancement in the value
<ENTER> Used to select a value and store it
to memory
Use the control panel to select the operating mode, as well as the sub-features. For a detailed layout
of the control panel functions, please see the “menu map” section on the previous page.
Menu Map
MENU SELECTION 1 SELECTION 2 DESCRIPTION
DMX Address d001~512 DMX starting address
Standalone Mode
SLAv Son Standalone: Slave receive mode
Nsts SrUn Standalone: sound-active
NAFA FASt Standalone: fast
NASL SLoU Standalone: slow
Pan Invert PAN Normal pan
rPAN Pan invert
Tilt Invert tit Normal tilt
Rtit Tilt invert
Display Invert Dis Normal display
RdiS Invert the display
Personality 8CH 8-channel personality
5CH 5-channel personality
Reset rESt Reset all motors to correct any errors with
motors misaligning during operation
Load Default LoAd Load all settings back to the factory default
Configuring the Starting Address
The Intimidator™ Scan LED 200 fixture uses up to 8DMX channels. In this DMX
configuration/personality, the highest channel that the fixture may be set to in order to function
properly is 505. Any address higher than this will prevent access to all of the channels, while in this
mode; however, if you desire to use one of the other DMX channels configurations (personalities),
please consider the total DMX channels when selecting a DMX address.
The Intimidator™ Scan LED 200 fixture uses 8 or 5 DMX channels, depending on the selected DMX
configuration (personality). If this is your first time using DMX, we recommend reading the “DMX
Primer” section in the “Appendix”.

4. Operating Instructions 10 12/9/2010 10:32 AM
Operation
DMX Operation
This is the operating mode which will allow for control with an external DMX controller. You must set the
starting address for this mode. If this is your first time using DMX, then it is recommended that you refer
to the “DMX Primer” section in the “Appendix” of this manual.
1. Press <MODE/ESC> until d*** appears on the LED screen.
2. Using <UP> and <DOWN>, select the starting address (001~512).
3. Press <ENTER>.
4. Press <MODE/ESC> until one of the DMX personalities appears on the LED screen
(8-CH, 5-CH).
5. Using <UP> and <DOWN>, select the desired DMX personality.
6. Press <ENTER>.
Only connect 32 fixtures to a single DMX daisy chain!
Master/Slave Mode (Sound-Active, Auto Mode)
This mode allows a single unit, the master, to operate in one of the standalone modes, while one or
more fixtures, slaves, synchronize their responses to the master.
Master:
The master fixture may be set in any of the STANDALONE modes: sound-active, fast, or slow.
Slave:
1. Press <MODE/ESC> until one of the standalone modes appears on the LED screen
(SLAv, NStS, NAFA, NASL).
2. Using <UP> and <DOWN>, select SLAv.
3. Press < ENTER >.
Only connect 31 slave fixtures when operating in this mode!
Automatic-Slow
This fixture has a preprogrammed chase that will operate in a preprogrammed, slow playback
speed.
Access this mode via the control panel on the front of the fixture. Please see the instructions
below for further explanation.
1. Press <MODE/ESC> until one of the standalone modes appears on the LED screen
(SLAv, NStS, NAFA, NASL).
2. Using <UP> and <DOWN>, select NASL.
3. Press <ENTER>.
Automatic-Fast
This fixture has a preprogrammed chase that will operate in a preprogrammed, fast playback
speed.
Access this mode via the control panel on the front of the fixture. Please see the instructions
below for further explanation.
1. Press <MODE/ESC> until one of the standalone modes appears on the LED screen
(SLAv, NStS, NAFA, NASL).
2. Using <UP> and <DOWN>, select NAFA.
3. Press <ENTER>.

4. Operating Instructions 11 12/9/2010 10:32 AM
Sound-Active
This fixture has a preprogrammed, sound triggered chase.
Access this via the control panel on the front of the fixture. Adjust the microphone sensitivity from
the control panel. Please see the chart below for further explanation.
1. Press <MODE/ESC> until one of the standalone modes appears on the LED screen
(SLAv, NStS, NAFA, NASL).
2. Using <UP> and <DOWN>, select NStS.
3. Press <ENTER>.
The microphone will only respond to low frequencies (bass).
Service Mode
Hidden Menu Map
This fixture has a hidden menu. The purpose of this menu is to adjust the home position
(electronic adjustment) of the attributes listed below.
M
AIN
F UNCTION S ELECTION I NSTRUCTION
P128 000~255 Adjustment for pan
t128 000~255 Adjustment for tilt
G128 000~255 Adjustment for the gobo wheel
C128 000~255 Adjustment for the color wheel
H128 000~255 Adjustment for pan
Y128 000~255 Adjustment for tilt
Please see the instructions below to access this hidden menu:
1. Press < MODE/ESC > for at least 10 seconds.
2. Using <UP/DOWN>, enter the following pass code: “2323”. Press <UP> to change the
blinking digit in ascending order, and press <DOWN> to move on to the next digit.
3. Press <ENTER>.
This mode will be automatically terminated after 15 seconds of being idle.

4. Operating Instructions 12 12/9/2010 10:32 AM
DMX Channel Values
8-CH Mode
CHANNEL VALUE FUNCTION CHANNEL VALUE FUNCTION
1
000 Ù255 Pan 0°~180°
7
000 Ù007
008 Ù015
016 Ù023
024 Ù031
032 Ù039
040 Ù047
048 Ù055
056 Ù087
088 Ù095
096 Ù103
104 Ù111
112 Ù119
120 Ù127
128 Ù135
136 Ù143
144 Ù151
152 Ù159
160 Ù255
Function
No function
Pan/tilt move-in-black
Pan/tilt move-in-black (disable)
Color wheel move-in-black
Color wheel move-in-black (disabled)
Gobo wheel move-in-black
Gobo wheel move-in-black (disabled)
No Function
All movement move-in-black (disabled)
Reset pan/tilt
No Function
Reset color wheel
Reset gobo wheel
No Function
Reset prism
Reset focus
Reset all
No function
2
000 Ù255 Tilt 0°~90°
3
000 Ù007
008 Ù015
016 Ù023
024 Ù031
032 Ù039
040 Ù047
048 Ù055
056 Ù063
064 Ù071
072 Ù079
080 Ù087
088 Ù095
096 Ù103
104 Ù111
112 Ù119
120 Ù127
128 Ù191
192 Ù255
Color
Open (white)
Dark Blue
Yellow
Pink
Green
Red
Blue
Salmon Pink
White/dark blue
Dark blue/yellow
Yellow/pink
Pink/green
Green/red
Red/blue
Blue/salmon pink
Salmon pink/white
Rotate clockwise (slow ~ fast)
Rotate counter-clockwise (slow ~ fast)
8
000 Ù007
008 Ù023
024 Ù039
040 Ù055
056 Ù071
072 Ù087
088 Ù103
104 Ù119
120 Ù135
136 Ù151
152 Ù167
168 Ù183
184 Ù199
200 Ù215
216 Ù231
232 Ù247
248 Ù255
Movement Macros
No function
Automatic 1
Automatic 2
Automatic 3
Automatic 4
Automatic 5
Automatic 6
Automatic 7
Automatic 8
Sound 1
Sound 2
Sound 3
Sound 4
Sound 5
Sound 6
Sound 7
Sound 8
4
000 Ù003
004 Ù007
008 Ù215
216 Ù255
Shutter
Closed
Open
Strobe (slow ~ fast)
Open
5
000 Ù255 Dimmer Dimmer: 0%~100%
6
000 Ù007
008 Ù015
016 Ù023
024 Ù031
032 Ù039
040 Ù047
048 Ù055
056 Ù063
064 Ù071
072 Ù079
080 Ù087
088 Ù095
096 Ù103
104 Ù111
112 Ù119
120 Ù127
128 Ù191
192 Ù255
Gobo Wheel
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 7 shake, fast to slow
Gobo 6 shake, fast to slow
Gobo 5 shake, fast to slow
Gobo 4 shake, fast to slow
Gobo 3 shake, fast to slow
Gobo 2 shake, (fast Ùslow)
Gobo 1 shake, (fast Ùslow)
Open
Gobo scroll: Clockwise rotation
Gobo scroll: Counter-clockwise rotation

4. Operating Instructions 13 12/9/2010 10:32 AM
5-CH Mode
CHANNEL VALUE FUNCTION
1
000 Ù255 Pan 0°~180°
2
000 Ù255 Tilt 0°~90°
3
000 Ù006
007 Ù013
014 Ù020
021 Ù027
028 Ù034
035 Ù041
042 Ù048
049 Ù055
056 Ù063
064 Ù070
071 Ù077
078 Ù084
085 Ù091
092 Ù098
099 Ù105
106 Ù112
113 Ù119
120 Ù127
128 Ù191
192 Ù255
Color
Open (white)
Yellow
Pink
Green
Peachblow
Blue
Kelly
Red
Dark blue
White/yellow (split colors)
Yellow/pink (split colors)
Pink/green (split colors)
Green/peach blow (split colors)
Peachblow/blue (split colors)
Blue/Kelly (split colors)
Kelly/red (split colors)
Red/dark blue (split colors)
Dark blue/white (split colors)
Rotate clockwise (slow ~ fast)
Rotate counter-clockwise (slow ~ fast)
4
000 Ù003
004 Ù007
008 Ù215
216 Ù255
Shutter
Closed
Open
Strobe (slow ~ fast)
Open
5
000 Ù007
008 Ù015
016 Ù023
024 Ù031
032 Ù039
040 Ù047
048 Ù055
056 Ù063
064 Ù071
072 Ù079
080 Ù087
088 Ù095
096 Ù103
104 Ù111
112 Ù119
120 Ù127
128 Ù191
192 Ù255
Gobo Wheel
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 7 shake, fast to slow
Gobo 6 shake, fast to slow
Gobo 5 shake, fast to slow
Gobo 4 shake, fast to slow
Gobo 3 shake, fast to slow
Gobo 2 shake, (fast Ùslow)
Gobo 1 shake, (fast Ùslow)
Open
Gobo scroll: Clockwise rotation
Gobo scroll: Counter-clockwise rotation

5. Appendix 14 12/9/2010 10:32 AM
5.APPENDIX
General Troubleshooting
S
YMPTOM P OSSIBLE C AUSE ( S ) P OSSIBLE A CTION ( S )
Breaker/Fuse
keeps blowing
•Excessive circuit load
•
Check total load placed on the
electrical circuit.
•Short circuit along the power
wires •Check for a short in the electrical wiring (internal and/or external).
Device does not
power up
•
No power
•
Check for power on Mains.
•Loose power cord •Check power cord
Fixture is not
responding to DMX
•Wrong DMX addressing
•
Check Control Panel and unit
addressing
•
Damaged DMX cables
•
Check DMX cables
•
Wrong polarity settings on the
controller
•
Check polarity switch settings on
the controller
•
Loose DMX cables
•
Check cable connections
•
Faulty DMX interface
•
Replace DMX input
•
Faulty Main PCB
•
Replace Main PCB
Loss of signal
•
Non DMX cables
•
Use only DMX compatible cables
•
Bouncing signals
•
Install terminator as suggested.
•Long cable / Low level signal
•
Install amplifier right after fixture
with strong signal.
•Too many fixtures
•
Install an optically coupled DMX
splitter after unit #32.
•Interference from AC wires
•
Keep DMX cables separated from
power cables or black lights.
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support.

5. Appendix 15 12/9/2010 10:32 AM
DMX Primer
There are 512 channels in a DMX connection. A fixture capable of receiving DMX will require one
or a number of sequential channels. The user must assign a starting address on the fixture that
indicates the first channel reserved in the controller. There are many different types of DMX
controllable fixtures and they all may vary in the total number of channels required. Choosing a
start address should be planned in advance. Channels should never overlap. If they do, this will
result in erratic operation of the fixtures whose starting address is set incorrectly. You can
however, control multiple fixtures of the same type using the same starting address as long as the
intended result is that of unison movement or operation. In other words, the fixtures will all
respond exactly the same.
DMX fixtures are designed to receive data through a daisy chain. A daisy chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in
which the fixtures are connected is not important and has no effect on how a controller
communicates to each fixture. Use an order that provides for the easiest and most direct cabling.
Connect fixtures using shielded two conductor twisted pair DMX data cable with three pin XLR
male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and
pin 3 is Data positive (S+).
Fixture Linking (Daisy Chain)
You will need a daisy chain to run light shows of one or more fixtures using a DMX controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The
combined number of channels required by all the fixtures on a daisy chain determines the number
of fixtures the data link can support.
To comply with the EIA-485 standard, do not connect more than 32 fixtures on one daisy
chain. Connecting more than 32 fixtures on one daisy chain without the use of a DMX
optically-isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended cable distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a daisy chain: 32
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified
DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create
your own cable please use data-grade cables that can carry a high quality signal and are less
prone to electromagnetic interference.
DMX Data Cable
Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485
applications. Standard microphone cables cannot transmit DMX data reliably over long distances.
The cable must have the following characteristics:
Type: shielded, 2-conductor twisted pair
Maximum capacitance between conductors: 30 pF/ft
Maximum capacitance between conductor and shield: 55 pF/ft
Maximum resistance: 20 ohms/1000 ft
Nominal impedance: 100 ~ 140 ohms

5. Appendix 16 12/9/2010 10:32 AM
Cable Connectors
Cabling must have a male XLR connector on one end and a female XLR
connector on the other end.
Do not allow contact between the common and the fixture’s chassis ground. Grounding
the common can cause a ground loop, and your fixture may perform erratically. Test
cables with an ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
Setting the Starting Address
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a
start address from 1~512. A fixture requiring one or more channels for control begins to read the
data on the channel indicated by the start address. For example, a fixture that uses six DMX
channels and was addressed to start on DMX channel 100, would read data from channels: 100,
101, 102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap,
and note the start address selected for future reference.
If this is your first time addressing a fixture using the DMX control protocol, we suggest jumping
to the “Appendix” section and reading the heading “DMX Primer”. It contains very useful
information that will help you understand its use.
COMMON
DMX +
DMX
-
INPUT OUTPUT
13
2
1
3
2
1
3
2
120 ohm ¼ W resistor
between pin 2 (DMX -) and
pin 3 (DMX +) on the
output of the last fixture
To avoid signal transmission problems
and interference, it is always advisable to
connect a DMX signal terminator.
DMX connector configuration
Terminator

5. Appendix 17 12/9/2010 10:32 AM
3-Pin to 5-Pin Conversion Chart
If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to
3-pin adapter. The chart below details a proper cable conversion:
3-P
IN TO 5-P IN C ONVERSION C HART
Conductor 3-Pin Female (Output) 5-Pin Male (Input)
Ground/Shield Pin 1 Pin 1
Data ( - ) signal Pin 2 Pin 2
Data ( + ) signal Pin 3 Pin 3
Not used Pin 4
Not used Pin 5
Setting up a DMX Daisy Chain
1. Connect the (male) 3-pin connector side of
the DMX cable to the output (female) 3-pin
connector of the controller.
2. Connect the end of the cable coming from the
controller which will have a (female) 3-pin
connector to the input connector of the next
fixture consisting of a (male) 3-pin connector.
3. Then, proceed to connect from the output as
stated above to the input of the following
fixture and so on.
Universal DMX Controller
This drawing
provides a general
illustration of the
DMX input/output
panel of a lighting
fixture.
Continue the link

5. Appendix 18 12/9/2010 10:32 AM
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently.
Usage and environment are contributing factors in determining frequency. As a general rule,
fixtures should be cleaned at least twice a month. Dust build up reduces light output performance
and can cause overheating. This can lead to reduced lamp life and increased mechanical wear.
Be sure to power off fixture before conducting maintenance.
•Unplug fixture from power.
•Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
•Clean all lenses when the fixture is cool with a mild solution of glass cleaner or
Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue.
•Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
•Gently polish optical surfaces until they are free of haze and lint.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
TECHNICAL SPECIFICATIONS
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be
issued. Package must be clearly labeled with a Return Merchandize Authorization Number (RMA
#). Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA #
prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief
description of the cause for the return. Be sure to pack fixture properly; any shipping damage
resulting from inadequate packaging is the customer’s responsibility. As a suggestion, proper
UPS packing or double-boxing is always a safe method to use. CHAUVET® reserves the right to
use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper
inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify
and submit claims with the shipper in the event that a fixture is damaged due to shipping. Any
other claim for items such as missing component/part, damage not related to shipping, and
concealed damage, must be made within seven (7) days of receiving merchandise.

WEIGHT & DIMENSIONS
Length...........................................................................................................13.2 in (335 mm)
Width...............................................................................................................6.6 in (168 mm)
Height............................................................................................................14.5 in (368 mm)
Weight.............................................................................................................. 7.5 lbs (3.4 kg)
MOVEMENT RANGE
Pan....................................................................................................................................180°
Tilt.......................................................................................................................................90°
POWER
Auto-ranging .....................................................................................100~240 VAC, 50/60 Hz
Power consumption @ 120 V ....................................................68 W (1 A) max, 0.4 A inrush
Power consumption @ 230 V .................................................67 W (0.5 A) max, 0.5 A inrush
Power output..........................................................................................................8 units max
LIGHT SOURCE
Type........................................................................................high-power, single source LED
Quantity......................................................................................................................1 (white)
Rating (red, green, blue)......................................................................(15 W) 1 A, 50,000 hrs
PHOTO OPTIC
Lux...................................................................................................................... 9,000 @ 1 m
Beam angle.........................................................................................................................15°
INDOOR/OUTDOOR
Rating........................................................................................................For indoor use only
THERMAL
Maximum ambient temperature........................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input.................................................................................locking 3-pin XLR male socket
Data output ...........................................................................locking 3-pin XLR female socket
Data pin configuration...............................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................DMX-512 USITT
DMX Channels (user-configurable) ................................................................................5 or 8
ORDERING INFORMATION
Intimidator™ Scan LED 200 ......................................................INTIMIDATORSCANLED200
WARRANTY INFORMATION
Warranty ..............................................................................................2-year limited warranty
CONTACT US
WORLD WIDE
General Information..............................................................................................CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954-929-1115
fax: [phone]
toll free: 800-762-1084
Technical Support.................................................................................................CHAUVET®
5200 NW 108th Ave
Sunrise, FL 33351
voice: 954-929-1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web.....................................................................http://www.chauvetlighting.com