Chauvet Intimidator Barrel LED 300 User manual

User Manual

Page 2 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
TABLE OF CONTENTS
1. Before You Begin................................................................................3
What Is Included ...........................................................................................3
Unpacking Instructions..................................................................................3
Claims...................................................................................................................3
Text Conventions ..........................................................................................3
Icons.............................................................................................................3
Document Information.....................................Error! Bookmark not defined.
Product at a Glance.......................................................................................4
Safety Notes .................................................................................................4
2. Introduction.........................................................................................5
Product Overview..........................................................................................5
Product Dimensions......................................................................................6
3. Setup...................................................................................................7
AC Power......................................................................................................7
Fuse Replacement.................................................................................................7
Power Linking........................................................................................................8
Mounting.......................................................................................................9
Orientation.............................................................................................................9
Rigging..................................................................................................................9
4. Operation ..........................................................................................10
Control Panel Operation..............................................................................10
Menu Map...................................................................................................10
Configuration (DMX)....................................................................................10
DMX Personalities and Starting Address..............................................................10
DMX Channel Assignments and Values.......................................................11
11-CH..................................................................................................................11
8-CH....................................................................................................................13
Configuration (Standalone)..........................................................................14
Sound Active Mode..............................................................................................14
Automatic Mode...................................................................................................14
Manual Pan Operation .........................................................................................14
Display................................................................................................................14
Reset Software ....................................................................................................14
Gobo Replacement..............................................................................................14
Master/Slave Mode..............................................................................................15
5. Technical Information ......................................................................16
Product Maintenance ..................................................................................16
Contact Us..................................................................................................17
Returns.......................................................................................................17
6. Technical Specifications..................................................................18

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 3 of 18
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator™ Barrel LED 300
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Upon receipt, carefully unpack the product and check the box to make sure you have
received all the parts in good condition.
Claims
If the box or the contents appear damaged from shipping, or show signs of mishandling,
upon receipt notify the carrier immediately, not CHAUVET®.
Failure to do so in a timely
manner may invalidate your claim with the carrier. In addition, keep
the container and all
the packing material for inspection.
For other issues
such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
Text
Conventions
Convention Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Icons
Icon
Meaning
This paragraph contains critical installation, configuration, or
operation information. Failure to comply with this information may
render the product partially or completely inoperative, cause
damage to the product, or cause harm to the user.
This paragraph contains important installation or configuration
information. Failure to comply with this information may prevent
the product from functioning correctly.
This paragraph reminds you of useful, although not critical,
information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual. CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Diaz 4/2/12 S. Graham 4/2/12

Page 4 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Switchable voltage (120 V / 230 V)

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center
•Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 5 of 18
2.INTRODUCTION
Product Overview
Bracket Adjustment Knob
DMX In
DMX Out
Voltage Switch
Power In
Power Out
Fuse Holder

Page 6 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
Product Dimensions

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 7 of 18
3.SETUP
AC Power
The Intimidator™ Barrel LED 300
has a dual voltage power supply and it can work with
an input voltage of either 120 V, 60 Hz or 230 V, 50 Hz, depending on the position of the
voltage selection switch.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement Follow the instructions below to change the fuse, if necessary.
Disconnect the product from the power outlet before replacing the fuse.
1. Disconnect this product from the power outlet.
2.
Using a Phillips #2 head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power
The product does not ship with a spare fuse; however, the safety cap has room
for a spare.

Page 8 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
Power Linking
The product provides power linking via the IEC outlet located in the back
of the unit.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to three (3) Intimidator™ Barrel LED 300 unit
s on 120 VAC
or up to seven (7) Intimidator™ Barrel LED 300 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Other products

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 9 of 18
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Intimidator™ Barrel LED 300
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product
can support
the product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13-mm hole, which is appropriate for
this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
Mounting Bracket
Bracket
Adjustment Knob

Page 10 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located
underneath the
display. See the Product Overview to see the button locations on the control panel.
Button
Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
DMX Address 001-512 Sets the DMX starting address
Operation
Modes
SLAv (Son) Slave operating mode
NStS (SrUn)
Sound-Active mode
NAFA (FASt)
Automatic mode, fast program
NASl (SLoU) Automatic mode, slow program
Pan
Normal Pan
PAn
Normal Pan operation
Inverse Pan rPAn Inverse Pan operation
Display
Normal
Display Dis Change the LED display text position
Inverse
Display rDis
Channel Mode
11-Channel
Mode 11CH Selects the DMX personality
8-Channel
Mode 8CH
Reset
rESt
Resets product
Load
LoAd
Load factory defaults
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
DMX
Personalities
and
Starting
Address
The Intimidator™ Barrel LED 300 has two DMX personalities, from an 8 channel mode for
basic control to an 11-channel mode with more advanced control over the lights.
The Intimidator™ Barrel LED 300 uses up to 11 DMX channels in its highest
DMX mode,
which defines the highest configurable address to 502.
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that
is too high, you could
restrict the access to some of the product’s channels.
If you are not familiar with the DMX protocol, download the DMX Primer
from
www.chauvetlighting.com.
To select the DMX personality, do the following:
1. Press <MENU> repeatedly until 8-CH or 11CH shows on the display.
2. Press <ENTER> to choose your DMX personality when it appears on the display.
To then choose your starting address:
1. Press <MENU> repeatedly until d001 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 11 of 18
DMX Channel Assignments and Values
11-CH
Channel Function Value Setting
1
Pan
000 255
0~180°
2
Tilt
000 255
0~90°
3 Color
000

006
White
007 013
Yellow
014 020
Pink
021 027
Green
028 034
Red
035 041
Light Blue
042 048
Kelly Green
049 055
Orange
056 063
Dark Blue
064 070
White + Yellow
071

077
Yellow + Pink
078 084
Pink + Green
085 091
Green + Red
092 098
Red + Light Blue
099 105
Light Blue + Kelly Green
106 112
Kelly Green + Orange
113 119
Orange + Dark Blue
120 127
Dark Blue + White
128 191
Rotate clockwise (slow to fast)
192 255
Rotate counterclockwise (slow to fast)
4 Shutter
000 003
Closed
004 007
Open
008 215
Strobe effect with increasing speed
216 255
Open
5
Dimmer
000 255
0~100%
6 Gobo Wheel
064 071
Gobo 7 shake, from slow to fast
072 079
Gobo 6 shake, from slow to fast
080 087
Gobo 5 shake, from slow to fast
088 095
Gobo 4 shake, from slow to fast
096

103
Gobo 3 shake, from slow to fast
104 111
Gobo 2 shake, from slow to fast
112 119
Gobo 1 shake, from slow to fast
120 127
Open
128 191
Cycle effect with increasing speed
192 255
Reverse cycle effect with increasing speed

Page 12 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
11-CH (con’t)
Channel
Function
Value
Setting
7 Gobo Rotation
000 015
Indexing
016

127
Rotation effect with increasing speed
128 239
Reverse rotation effect with increasing speed
240 255
Gobo bounce
8 Prism
000 003
Open
004 255
Prism on
9
Focus
000 255
0~100%
10 Control Functions
000 007
No function
008 015
Blackout while pan/tilt moving
016 023
Disable blackout while pan/tilt moving
024 031
Blackout while moving color wheel
032 039
Disable blackout while moving color wheel
040 047
Blackout while moving gobo wheel
048 055
Disable blackout while moving gobo wheel
056 087
No function
088 095
Disable blackout while moving all options
096

103
Reset pan/tilt
104 111
No function
112 119
Reset color wheel
120 127
Reset gobo wheel
128 135
No function
136 143
Reset prism
144 151
Reset focus
152 159
Reset all
160 255
No function
11 Movement Macros
000 007
No function
008 023
Movement macro 1
024 039
Movement macro 2
040 055
Movement macro 3
056 071
Movement macro 4
072 087
Movement macro 5
088

103
Movement macro 6
104 119
Movement macro 7
120 135
Movement macro 8
136 151
Sound controlled program 1
152 167
Sound controlled program 2
168 183
Sound controlled program 3
184 199
Sound controlled program 4
200 215
Sound controlled program 5
216 231
Sound controlled program 6
232 247
Sound controlled program 7
248 255
Sound controlled program 8

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 13 of 18
8-CH
Channel Function Value Setting
1
Pan
000 255
0~180°
2
Tilt
000 255
0~90°
3 Color
000 006
White
007 013
Yellow
014 020
Pink
021 027
Green
028 034
Red
035 041
Light Blue
042 048
Kelly Green
049 055
Orange
056 063
Dark Blue
064 070
White + Yellow
071 077
Yellow + Pink
078 084
Pink + Green
085 091
Green + Red
092 098
Red + Light Blue
099

105
Light Blue + Kelly Green
106 112
Kelly Green + Orange
113 119
Orange + Dark Blue
120 127
Dark Blue + White
128 191
Rotate clockwise (slow to fast)
192 255
Rotate counterclockwise (slow to fast)
4 Shutter
000 003
Closed
004 007
Open
008 215
Strobe effect with increasing speed
216 255
Open
5 Gobo Wheel
064 071
Gobo 7 shake, from slow to fast
072 079
Gobo 6 shake ,from slow to fast
080 087
Gobo 5 shake, from slow to fast
088 095
Gobo 4 shake, from slow to fast
096 103
Gobo 3 shake, from slow to fast
104 111
Gobo 2 shake, from slow to fast
112 119
Gobo 1 shake, from slow to fast
120 127
Open
128 191
Cycle effect with increasing speed
192 255
Reverse cycle effect with increasing speed
6 Gobo Rotation
000 015
Indexing
016 127
Rotation effect with increasing speed
128 239
Reverse rotation effect with increasing speed
240 255
Gobo bounce
7 Prism
000 003
Open
004 255
Prism on
8
Focus
000

255
0~100%

Page 14 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode
to a DMX
controller. Products in standalone mode could interfere with the controller.
Sound Active
Mode
To enable the Sound Active mode, do the following:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASl, NAFA, NStS,or SLAv.
2. Press <UP> or <DOWN> to select NStS.
3. Press <ENTER>.
4. Turn the music on and adjust the microphone sensitivity knob until the product
starts responding to the beat of the music.
The product will only respond to low frequencies of music (bass and drums).
Automatic Mode
To enable the Automatic Mode:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASl, NAFA, NStS,or SLAv.
2. Press <UP> or <DOWN> to select NASl (for a slow light show) or NAFA (for a fast
light show).
3. Press
<ENTER>
.
Manual Pan
Operation
To select whether you want the Intimidator™ Barrel LED 300 to operate with normal
panning or inverted panning, do the following:
1. Press <MODE/ESC> repeatedly until PAn shows on the display.
2. Press <UP> or <DOWN> to select normal pan operation (PAn) or inverse pan
operation (r PAn).
3. Press <ENTER>.
Display
You are able to flip the LED display for easy readability in any mounting situation. To
select your display angle:
1. Press <MODE/ESC> repeatedly until diS shows on the display.
2. Press <UP> or <DOWN> to select normal display mode (diS) or inverse display
mode (r diS).
3. Press <ENTER>.
Reset Software
To reset the software on the Intimidator™ Barrel LED 300:
1. Press <MODE/ESC> repeatedly until rESt shows on the display.
2. Press <ENTER>.
The product will reset all settings in the software to the default
factory settings.
Gobo
Replacement
The Intimidator™ Barrel LED 300 has replaceable gobos:
1. Turn off and disconnect product from power.
2. Open the head cover by loosening the 10 fastening screws at the sides of the top
cover.
3. Remove the 4 screws on the cover plate underneath the display to access the gobo
wheel.
4.
Separate the gobo plate away from the gobo wheel by pushing it toward the front of
the mirror. Be careful not to push the gobo out of the gobo plate.
5. Then extract the gobo plate by pulling it outward.
6. On a flat surface, remove the expansion ring that holds the gobo in place and
remove the gobo from the gobo plate.
7. Insert a new gobo and hold it in place with the expansion ring.
8. Slide the tip of the gobo plate under the pressure plate near the center of the gobo
wheel.
9. Push the gobo plate inwards. DO NOT force the gobo plate into the gobo wheel
slot. If correctly installed, the gobo plate should accommodate itself in the gobo
wheel slot.
10. Replace cover.

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 15 of 18
Master/Slave
Mode
The Master/Slave mode allows a single Intimidator™ Barrel LED 300
unit (the “master”)
to control the actions of one or more Intimidator™ Barrel LED 300 units (the “slaves”)
without the need of a DMX controller
. The master unit will be set to operate in either
Automatic or Sound Active mode, while the slave units will be set to operate in Slave
Mode. Once set and connected, the slaves will operate in unison with the master unit.
Slave mode:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASl, NAFA, NStS, or SLAv.
2. Press <UP> or <DOWN> to select SLAv.
3. Press <ENTER> to accept.
4. Set the DMX address to 001.
5. Connect the DMX input of the first slave unit to the DMX output of the master unit.
6. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
7. Finish setting and connecting all the slave units.
Master mode:
1. Set the master unit to operate in either Automatic or Sound mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure
all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with
the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.

Page 16 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, you should clean your lighting products at least twice a
month. However, be aware that usage and environmental conditions could be
contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents and reachable internal components.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly drag any dirt or grime to the outside edges of the external optics or
glass/transparent surface.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint.
•When cleaning units with one or more movable mirrors, you should keep the contact
with the mirror’s surface to a minimum to avoid scratching or damaging it.
Always dry the external optics and glass/transparent
surfaces carefully after
cleaning them.

Intimidator™ Barrel LED 300 User Manual (Rev. 5) Page 17 of 18
In case you need to return a product or request support, follow the procedure below:
•If you live in the U.S., contact CHAUVET® World Headquarters (see below).
•If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. Refer to our website for contact details of distributors outside
the U.S., United Kingdom, or Ireland.
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
s to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET®
Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial
number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. Proper FedEx packing or double-boxing are
recommended.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).

Page 18 of 18 Intimidator™ Barrel LED 300 User Manual (Rev. 5)
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
20.5 in (521 mm)
10 in (255 mm)
6.7 in (171 mm)
14.2 lbs (6.4 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (external)
120 V, 60 Hz, 230 V, 50 Hz
Switchable
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
240 W
240 W
Operating
2 A
1 A
Power linking current (units)
8 A (3 units)
8 A (7 units)
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
N/A
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
60 W (15 A)
50,000 hours
Color
Quantity
Current
White
1
15 mA
Photo Optic
Parameter
Illuminance @ 2 m
1,736 lux
Pan/Tilt
180°
360°
Strobe Rate
0-20 Hz
Gobo Size
23.8 mm outside
20.9 mm image
2 mm max thickness
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Fan
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
8, 11
Ordering
Product Name
Item Code
Item Number
Intimidator™ Barrel LED 300
08020473
INTBARRELLED300