Chauvet Colorado 2 Zoom Tour User manual

Quick Reference Guide

COLORado™ 2 Zoom Tour QRG
Page 2 of 12
About This
Guide
The COLORado™ 2 Zoom Tour Quick Reference Guide (QRG)
contains
the product’s connection and mounting information,
as well as the menu
options and the DMX values.
Disclaimer
•Refer to this product’s User Manual for detailed information and
instructions. You can download the User Manual from the CHAUVET®
website: www.chauvetpro.com.
•Read ALL the disclaimers and Safety Notes in this document, as well as
those in the product’s User Manual before installing, operating, or
maintaining this product.
Safety Notes
•DO NOT open this product unless instructed. It contains no user
serviceable parts.
•DO NOT aim this product toward any surface closer than 16 feet (5 m).
You may damage or overheat the illuminated surface.
•DO NOT aim this product toward the Sun. The lenses could concentrate
the solar energy and cause internal overheating.
•DO NOT look at the light source when this product is on.
•DO NOT touch the product when it is operating because it may be very
hot.
•DO NOT cover the ventilation slots when the product is operating to
avoid internal overheating.
•DO NOT install or operate this product where there is less than 50 cm to
the nearest surface to allow adequate ventilation around it.
•DO NOT leave any flammable material within 50 cm from this product
while operating or connected to the power outlet to minimize the risk of
fire.
•DO NOT mount this product overhead without using a safety cable.
•DO NOT operate this product outdoors or in any location where dust,
excessive heat, water, or humidity may affect it.
•DO NOT operate this product if you see damage on the housing, lenses,
or cables. In any of these cases, have the damaged parts replaced by an
authorized technician immediately.
•DO NOT connect this product to a dimmer or rheostat.
•ONLY connect this product to a grounded and protected circuit.
What Is
Included
•One COLORado™ 2 Zoom Tour
•One NEUTRIK® powerCON®
to Edison Plug Power Input Cord
•One Accessory Holder
•One Gel Frame
•One Warranty Card
•One Quick Reference Guide

COLORado™ 2 Zoom Tour QRG
Page 3 of 12
Features
•3, 4, 5, 6, or 12-channel DMX control
•Operating modes
3-channel: RGB
3-channel: HSV
4-channel: RGB, dimmer
4-channel: RGBW
5-channel: RGBW, dimmer
6-channel: RGBW, dimmer, strobe
12-channel: RGBW, dimmer, color macro, strobe, auto/custom
programs, auto speed, dimmer speed, zoom, zoom
reset
•RGBW color mixing with or without DMX control
•Zoom control with or without DMX control
•Built-in automated programs via master/slave or DMX
•Recall custom programs via master/slave or DMX
•Five distinct dimming curves
•RGBW LEDs
•Electronic dimmer
•Color macros with speed adjustment included
•Electronic power supply
•NEUTRIK® powerCON® connectors
•3- and 5-pin DMX input and output connectors
•Additional power output: max 7 units @ 120 VAC
•LED display with password protection
•Gel frame holder (4 mm max. thickness)
•Double-bracketed yoke doubles as a floor stand
•Color calibration
•
Flicker-free operation for HD video

COLORado™ 2 Zoom Tour QRG
Page 4 of 12
Product
Description
The COLORado™ 2 Zoom Tour is an RGBW LED wash product. A single
module houses the internal power supply, the control panel, the LED
drivers, the LED boards, and motorized moving lenses, as well as the power
and signal connectors. The COLORado™ 2
Zoom Tour features a variable
zoom enabling you to change the beam angle
via DMX or control panel.
One mounting bracket doubles as a floor mount or a
hanging support
bracket.
Product Overview
Rear View
Side View
Power
In/Out
Power
In/Out
DMX In
DMX
Out
Control
Panel
Adjustment Knob

COLORado™ 2 Zoom Tour QRG
Page 5 of 12
AC Power
This product has an auto-ranging power supply that works
with an
input voltage range of 100~240 VAC, 50/60 Hz.
Power Linking
You can link up to 7 COLORado™ 2 Zoom Tour products at 120
VAC, 60Hz or 15 products at 230VAC, 50Hz. N
ever exceed this
number.
DMX
Linking
The COLORado™ 2 Zoom Tour
can work with a DMX controller
when linked using a regular DMX serial connection.
If you are not familiar with the DMX standard, download the
DMX
Primer from www.chauvetpro.com.
DMX
Connection
The COLORado™ 2 Zoom Tour uses a regu
lar DMX data connection
for DMX personalities, TOUR, ARC.1, AR1.D, ARC.2, AR2.D,
AR2.S, and HSV.
Download the COLORado™ 2 Zoom Tour User Manual.
Refer to the
Setup
chapter to learn how to connect this product for DMX operation.
To learn h
ow to configure this product for DMX operation, refer to the
Operation chapter.
Master/Slave
Connection
The COLORado™ 2 Zoom Tour
uses the DMX data connection for
Master/Slave mode.
Download the COLORado™ 2 Zoom Tour User Manual
. Refer to the
Setup and Operation chapters to learn how to connect
and configure
this product for Master/Slave operation.

COLORado™ 2 Zoom Tour QRG
Page 6 of 12
Mounting
Before mounting this product, read the Safety Notes at the be
ginning of this
Guide and in the product’s User Manual
. Then, follow the mounting
procedure indicated in the Setup chapter of the User Manual.
Product
Mounting
Diagram
Overhead Mounting
Floor Mounting

COLORado™ 2 Zoom Tour QRG
Page 7 of 12
Programming
For details on how to program this product, please refer to the product’s
User Manual.
Control Panel
Description
Button Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value into the selected function
<UP>
Navigates upwards through the menu list and increases the
numeric value when in a function
<DOWN>
Navigates downwards through the menu list and decreases
the numeric value when in a function
Password
After being prompted to enter the password, press:
<UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>.
Start Address
To ensure full access to all channels in each DMX mode, the highest
recommended DMX addresses are as follows:
Mode
Address
Mode
Address
Mode
Address
TOUR
501
ARC.2
509
HSV
510
ARC.1
510
AR2.D
508
AR1.D
509
AR2.S
507

COLORado™ 2 Zoom Tour QRG
Page 8 of 12
Menu Options
Main Level Programming Levels Description
STAT
R.
000~255 Combines Red, Green, Blue, and White to
generate a custom color (0~100%)
G.
B.
W.
Z.
Changes the beam angle
S.
00~20
Strobe frequency (0~20 Hz)
AUTO
AT.01~10
Choose from 10 automatic programs
PR.C1~10
Choose from 10 customizable programs
DMX
001~512
Sets the DMX starting address
RUN
DMX
Receives signals from DMX controller
SLAV
Receives signals from Master unit
PERS
TOUR
12-channel: RGBW, D, A/C, AS, DS, Macro,
S, Z, ZR
ARC.1
3 channel: RGB
AR1.D
4-channel: RGB, D
ARC.2
4-channel: RGBW
AR2.D
5-channel: RGBW, D
AR2.S
6-channel: RGBW, D, S
HSV
3 channel: HSV

COLORado™ 2 Zoom Tour QRG
Page 9 of 12
Main Level Programming Levels Description
SET
UPLD
Enter password
Transfers custom programs
REST
Enter password
Defaults fixture
DIM
OFF
No dimmer
DIM1~4
Dimmer curve
DERR
BLAC
All LED’s turn off when DMX signal is lost
SAVE
All LED’s stay on the last command used
when the DMX signal is lost.
COLR
OFF
RGB set to “255” = max. output
RGBW
RGB set to “255” = balanced white
UC
Universal color balance
ZOOM
BASE
Sets default zoom position (full movement)
POS.1
Sets position 1 setting for zoom limit
POS.2
Sets position 2 setting for zoom limit
EDIT PR.
(C1~10) SC. (01~30)
R.
000~255 Combines Red, Green, Blue, White, and
Zoom, as well as strobe and timers to
create the scenes of a custom program
G.
B.
W.
Z.
S.
00~20
T.
000~255
F.
KEY
ON/OFF
Turns the password on or off
CAL
PASS
(
Enter
pass
word)
CAL
WT
WH
1~11
R.
000~255
Modifies the color macros used in channel 6
of the TOUR personality
G.
B.
W.
RGB
W
RGB
.W
R.
000~255
Defines the color temperature used when
COLOR is set to RGB to W
G.
B.
ZOOM
POS.1
000~255
Sets min/max position of zoom
POS.2

COLORado™ 2 Zoom Tour QRG
Page 10 of 12
DMX Values
Tour
Channel
Function Value
Percent/Setting
1
Dimmer
000 ó255
0~100%
2
Red
000 ó255
0~100%
Step Time
When CUS. 01-10 in CH. 8 is activated
3
Green
000 ó255
0~100%
Step Time
When CUS. 01-10 in CH. 8 is activated
4
Blue
000 ó255
0~100%
5
White
000 ó255
0~100%
6 Color Macro + White
Balance
000 ó010
011 ó030
031 ó050
051 ó070
071 ó090
091 ó110
111 ó130
131 ó150
151 ó170
171 ó200
201 ó205
206 ó210
211 ó215
216 ó220
221 ó225
226 ó230
231 ó235
236 ó240
241 ó245
246 ó250
250 ó255
No Function
R: 100%
G: 0~100% B: 0%
R:
100~0% G: 100% B: 0%
R: 0%
G: 100% B: 0~100%
R: 0%
G: 100~0% B: 100%
R:
0~100% G: 0% B: 100%
R: 100%
G: 0% B: 100~0%
R: 100%
G: 0~100% B: 0~100%
R:
100~0% G: 100~0% B: 100%
R:
100% G: 100% B: 100% W: 100%
White 1:
3,200 K
White 2:
3,400 K
White 3:
4,200 K
White 4:
4,900 K
White 5:
5,600 K
White 6:
5,900 K
White 7:
6,500 K
White 8:
7,200 K
White 9:
8,000 K
White 10:
8,500 K
White 10: 10,000 K
7 Strobe
000 ó009
010 ó255
No Function
0~20 Hz
8 Auto + Custom
Programs
000 ó040
041 ó049
050 ó059
060 ó069
070 ó079
080 ó089
090 ó099
100 ó109
110 ó119
120 ó129
130 ó139
140 ó149
150 ó159
160 ó169
170 ó179
180 ó189
190 ó199
200 ó209
No function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Continues on the next page