Chauvet LX 10 User manual

Snapshot
OK on Dimmer
Outdoor OK
Sound Activated
DMX512
Master/Slave
115V/230V Switch
Replaceable Fuse
User Serviceable
Duty Cycle
LX10™
USER MANUAL
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com

TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
ACPOWER...........................................................................................................................................................................................3
CONTACT US........................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 5
FEATURES............................................................................................................................................................................................5
PRODUCT OVERVIEW ............................................................................................................................................................................5
3. SETUP............................................................................................................................................................................... 6
FUSE REPLACEMENT.............................................................................................................................................................................6
MOUNTING ...........................................................................................................................................................................................6
Orientation.......................................................................................................................................................................................................6
Rigging............................................................................................................................................................................................................6
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 7
TROUBLESHOOTING...............................................................................................................................................................................7
GENERAL TROUBLESHOOTING................................................................................................................................................................8
TECHNICAL SUPPORT............................................................................................................................................................................8
GENERAL MAINTENANCE .......................................................................................................................................................................9
RETURNS PROCEDURE..........................................................................................................................................................................9
CLAIMS ................................................................................................................................................................................................9
TECHNICAL SPECIFICATIONS ................................................................................................................................................................10
LX10 2 9/11/2007 2:36 PM

1. BEFORE YOU BEGIN
What is included
¾1 x LX10™
¾Power Cord
¾Warranty Card
¾User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
Figure 1 - AC Voltage Switch
Not all fixtures have a voltage
select switch. Please be sure to
connect to the proper voltage.
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a
fixture, check that the source voltage matches the fixture’s requirement.
Check the fixture or device carefully to make sure that if a voltage selection
switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the
line voltage applied. Damage to your fixture may result if the
line voltage applied does not match the voltage indicated on
the voltage selector switch. All fixtures must be connected to
circuits with a suitable Earth Ground.
Contact Us
World Wide
General Information Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support Chauvet Lighting
3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com
LX10 3 9/11/2007 2:36 PM

Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only!
•To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no
flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse size and type.
•Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use
its carrying handles.
•Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center. Always use the same type spare parts.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Avoid direct eye exposure to the light source while it is on.
•Do not daisy chain power to more than 50 units.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET at: 954-929-1115.
LX10 4 9/11/2007 2:36 PM

2. INTRODUCTION
Features
•LED moonflower effect
•Mirror scans 180°
•Selectable functions: sound, rotating, static
•Additional power output for daisy chaining units (max 50 units)
•Sound sensitivity knob
•Ultra bright LEDs
•Low power consumption
Product Overview
Mounting
Bracket
Lens
Connection
Panel
(rear)
Scanning Mirror
110/230V
Selector Switch
Sound
Sensitivity
Adjustment
Knob
Mode
Selector
Switch
IEC Power
Connector with
Fuse Holder
Power Output
For LX series only!
Max 50 units
LX10 5 9/11/2007 2:36 PM

3. SETUP
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Fuse Replacement
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
With a flat head screwdriver wedge the fuse
holder out of its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
Mounting
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation.
RIGGING
Hanging Clamp
It is important never to obstruct the fan or vents pathway. Mount the
fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the fixture by
loosening both knobs and tilting the fixture. After finding the desired
position, retighten both knobs.
•When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
•Safety cables must always be used. Note!
Clamp is sold separatel
•Never mount in places where the fixture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
y
.
LX10 6 9/11/2007 2:36 PM

4. OPERATING INSTRUCTIONS
The LX10 motors can operate in Sound-Active, Auto, or static mode. The mode is determined by the
position of the switch located on the rear of the unit. To switch between the three modes, place the
switch in either the “I” or “II” position for movement, or “O” for static operation.
In the “II” position, the fixture operates in Sound-Active mode, the sensitivity of which can be adjusted
by the knob also located on the rear of the unit. To increase the sensitivity of the unit rotate the knob
clockwise.
In the “I” position the fixture operates in Auto mode. The light will rotate through a pre-programmed
routine, whether sound is present or not.
In the “O” position the fixture operates in static mode. The fixture will continue to light without
scanner movement.
= Automatic motors & LEDs
= Motors stop, LEDs auto
= Sound Active Motors & LEDs
Troubleshooting
1) Verify that the unit is plugged into both the wall and the unit, and verify that the fuse is in
working order.
2) If the unit fails to respond, place the unit in auto mode, listening for movement of the
motor inside the case. If no sound is heard from inside the case, replace fuse and retry.
3) If the unit is still not working, verify the integrity of the outlet with another fixture.
If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support at the location on the next page.
LX10 7 9/11/2007 2:36 PM

General Troubleshooting
Applies to
Symptom Solution(s)
Lights Foggers
& Snow Controllers Dimmers & Chaser
Auto shut off Check fan thermal switch reset 9
Beam is very dim or
not bright Clean optical system or replace lamp
Check 220/110v switch for proper setting 9
Breaker/Fuse keeps
blowing Check total load placed on device 9
Chase is too slow Check users manual for speed adjustment 999
Device has no power Check for power on Mains.
Check device’s fuse. (internal and/or external) 999
Fixture is on but
there is no
movement to the
audio
Make sure you have the correct audio mode on the
control switches. If audio provided via ¼” jack, make
sure a live audio signal exists
Adjust sound sensitivity knob
999
Lamps cuts off
sporadically Possible bad lamp or fixture is overheating.
Lamp may be at end of its life. 9
Light will not come
on after power failure Some discharge lamps require a cooling off period before the electronics in the fixture can kick start it
again, wait 5 to 10 minutes before powering up
9
Moves slow Check 220/110v switch for proper setting 9
No flash Re-install bulb, may have shifted in shipping 9
No light output Check slip ring & brushes for contact
Install bulb
Call service technician
9
Relay will not work Check reset switch
Check cable connections 9
Remote does not
work Make sure connector is firmly connected to device 99
Stand alone mode All Chauvet lighting fixtures featuring stand-alone
functions do not require additional settings, simply
power the fixture and it will automatically enter into this
mode
9
If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support at the location below.
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): [email protected]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com
LX10 8 9/11/2007 2:36 PM

General Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Note: If you are given an RA #, please include the following information on a piece of paper
inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
LX10 9 9/11/2007 2:36 PM

Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 15.5 in (394 mm)
Width .............................................................................................................................. 5.3 in (135 mm)
Height............................................................................................................................. 8.5 in (216 mm)
Weight .................................................................................................................................5 lbs (2.3 kg)
POWER
Switch-selectable power settings..............................................................120V 60Hz AC or 230V 50Hz
Fuse............................................................................................................................................1A 250V
Power Consumption....................................................................................11.9W (0.12A) max at 120V
Inrush Power ..........................................................................................................19W (0.34A) at 120V
Power Factor.......................................................................................................................0.70 at 120V
Power Output............................................................................50 units max at 110V, 100 units at 230V
LIGHT SOURCE
LED.................................................................................... 57 (17 Red, 24 Green, 16 Blue) 100,000 hrs
PHOTO OPTIC
Beam Angle..................................................................................................................................... 58.5°
THERMAL
Maximum ambient temperature...........................................................................................104°F (40°C)
ORDERING INFORMATION
LX10................................................................................................................................................ LX10
WARRANTY INFORMATION
Warranty.............................................................................................................. 1-year limited warranty
LX10 10 9/11/2007 2:36 PM