Chauvet Q-Wash 419Z-LED User manual

User Manual
Control Panel
Handles
Omega Brackets
Front View

Side View
Edition
Notes
This user manual covers the description, safety precautions, installation,
programming, operation, and maintenance of the Q-Wash™ 419Z-LED.
CHAUVET® released this edition of the Q-Wash™ 419Z-LED user manual in August
2013.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the CHAUVET® name and
the dotted triangle, and all other trademarks in this manual pertaining to services,
products, or marketing statements (example: It’s Green Thinking™) are owned or
licensed by CHAUVET®. Any other product names, logos, brands, company names,
and other trademarks featured or referred to within this document are the property of
their respective trademark holders.
Copyright
Notice
CHAUVET® owns the content of this user manual in its entirety, including but not
limited to pictures, logos, trademarks, and resources.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Use
CHAUVET® authorizes its customers to download and print this manual for
professional information purposes only. CHAUVET® expressly prohibits the usage,
copy, storage, distribution, modification, or printing of this manual or its content for any
other purpose without written consent from CHAUVET®.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in),
double-sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content accordingly.
Intended
Audience
Any person in charge of installing, operating, and/or maintaining this product should
completely read through the guide that shipped with the product, as well as this
manual, before installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any errors or omissions
in this document. CHAUVET® reserves the right to revise and make changes to the
content of this document without obligation that CHAUVET® notify any person or
company of such revision or changes. This does not in any way constitute a
commitment by CHAUVET® to make such changes. CHAUVET® may issue a
revision of this manual or a new edition to incorporate such changes.
Author
Date
Editor
Date
D. Couppe
08/12/13
T. Yeago
08/12/13
Quad-Color LEDs
Power Switch

Fuse
Power In/Out
Rear View
Top View
Data In/Out
13.43 in
341 mm
14.49 in
368 mm
11.69 in
297 mm
10.63 in
270 mm
3.86 in
98 mm
8.86 in
225 mm
13.31 in
338 mm
Clamp
Safety Cable
Floor Mounting
Overhead Mounting
Table of Contents
1. Before You Begin
...................................................................................................................................... 1
What Is Included
........................................................................................................................................................... 1
Claims
..........................................................................................................................................................................................
1
Manual Conventions
.................................................................................................................................................................... 1
Symbols
....................................................................................................................................................................................... 1
Safety Notes
................................................................................................................................................................. 2
Personal Safety
............................................................................................................................................................................ 2
Mounting and Rigging
.................................................................................................................................................................. 2
Power and Wiring
......................................................................................................................................................................... 2
Operation
..................................................................................................................................................................................... 2
Expected LED Lifespan
................................................................................................................................................ 2
2. Introduction
............................................................................................................................................... 3
Description
.................................................................................................................................................................... 3
Features
........................................................................................................................................................................

3
Overview
.......................................................................................................................................................................
4
Dimensions
................................................................................................................................................................... 5
3. Setup
.........................................................................................................................................................
. 6
AC Power
......................................................................................................................................................................
6
AC Plug
........................................................................................................................................................................................ 6
Power Linking
............................................................................................................................................................... 6
Fuse Replacement
....................................................................................................................................................................... 6
DMX
Linking.............................................................................................................................................................
..... 7
DMX Modes
................................................................................................................................................................................. 7
Master/Slave Connectivity
............................................................................................................................................................ 7
Mounting
.......................................................................................................................................................................
8
Orientation
................................................................................................................................................................................... 8
Rigging
.........................................................................................................................................................................................
8
4. Operation
................................................................................................................................................... 9
Control Panel Description
............................................................................................................................................. 9
Control Options
............................................................................................................................................................. 9
Programming
................................................................................................................................................................ 9
Control Panel Display
................................................................................................................................................................... 9
Display Backlight
.......................................................................................................................................................................... 9
Display Invert
............................................................................................................................................................................... 9
Control Panel Lock
..................................................................................................................................................................... 10
Password
................................................................................................................................................................................... 10
DMX Personality
........................................................................................................................................................................ 10
DMX
Control...............................................................................................................................................................................
10
Loss of Signal Setting
................................................................................................................................................................ 11

Static
Control..............................................................................................................................................................................
11
Auto/Custom Programs
.............................................................................................................................................................. 11
Edit Custom Programs
.............................................................................................................................................................. 12
Master/Slave
.............................................................................................................................................................................. 12
Fixture Cloning
........................................................................................................................................................................... 13
Fan Control
................................................................................................................................................................................ 13
Pan/Tilt
Speed............................................................................................................................................................................
13
Reverse Pan Direction
............................................................................................................................................................... 13
Reverse Tilt Direction
................................................................................................................................................................. 13
Optics
Speed..............................................................................................................................................................................
13
Reverse Dimmer Direction
......................................................................................................................................................... 13
Head Motion Black Out
.............................................................................................................................................................. 13
Color
Settings.............................................................................................................................................................................
14
Dimmer Curves
.......................................................................................................................................................................... 14
Zoom Position Adjust
................................................................................................................................................................. 15
Limit Pan/Tilt Range
................................................................................................................................................................... 15
Offset Calibration
....................................................................................................................................................................... 15
White Calibration
........................................................................................................................................................................ 15
Calibrating the
............................................................................................................................................................................ 15
White Color
................................................................................................................................................................................ 15
Product Reset Control
................................................................................................................................................................ 16
Reset
..........................................................................................................................................................................................
16
Custom Program Reset
.............................................................................................................................................................. 16
Reset to Factory Default
............................................................................................................................................................ 16
Software Version
........................................................................................................................................................................ 16
Menu Map
................................................................................................................................................................... 17
DMX Values
................................................................................................................................................................ 22
5. Technical Information

............................................................................................................................. 29
Product Maintenance
.................................................................................................................................................. 29
Returns
.......................................................................................................................................................................
29
Technical Specifications
............................................................................................................................................. 30
Contact Us
.................................................................................................................................................................. 31
1. Before You Begin
What Is
Included
Q-Wash™ 419Z-LED
powerCON® power cord
Omega bracket with mounting
hardware
Safety Cable
Warranty card
Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all
the parts are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear
damaged from shipping or show signs of mishandling, notify the carrier
immediately, not CHAUVET®. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and
contents for inspection.
For other issues, such as missing components or parts, damage not related
to shipping, or concealed damage, file a claim with CHAUVET® within 7
days of delivery.
Manual
Conventions
Convention
Meaning
1~512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1~10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols
Meaning
Critical installation, configuration, or operation information. Failure
to comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.

The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.
Safety
Notes
Read all the following Safety Notes before working with this product. These notes
include important information about the installation, usage, and maintenance of this
product.
This product contains no user-serviceable parts. Any reference to servicing in
this user manual will only apply to properly trained CHAUVET® certified
technicians. Do not open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal
Safety
Avoid direct eye exposure to the light source while the product is on.
Always disconnect this product from power before servicing.
Always connect this product to a grounded circuit to avoid the risk of
electrocution.
Do not touch this product’s housing when operating because it may be hot.
Mounting and
Rigging
This product is for indoor use only! To prevent risk of fire or shock, do not
expose this product to rain or moisture.
When hanging this product, always secure to a fastening device using a
safety cable (included).
Always carry this product using the built-in handles.
Do not leave any flammable material within 50 cm of this product while
operating.
Power and
Wiring
Always make sure you are connecting this product to the proper voltage in
accordance with the specifications in this manual or on the product’s specification
label.
Never connect this product to a dimmer pack or rheostat.
Never disconnect this product by pulling or tugging on the power cable.

Operation
Do not operate this product if you see damage on the housing, lenses, or
cables. In any of these cases, have the damaged parts replaced by an authorized
technician at once.
Do not cover the ventilation slots when the product is operating to avoid
internal overheating.
The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate
this product at a higher temperature.
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected
LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single-LED
conditions. For this reason, using clustered LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be 40,000 to
50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product and reducing the ambient temperature
to an optimal operating range. In addition, limiting the overall projection intensity may
also help to extend the LEDs’ lifespan.
2. Introduction
Description
The Q-Wash™ 419Z-LED is a high-power quad-color RGBW LED, moving head
wash product. This product consists of a base section and a moving yoke with a pan
range of up to 540º. The moving head, which has a tilt range of 270º, contains the 19
quad-color RGBW LEDs and the zoom motors. The base section has the 3- and 5-pin
DMX input and output sockets, the Neutrik® powerCON® input connector, and the
LCD-based control panel.
Features
19 LEDs quad-color RGBW (15 W)
Smooth Zoom and Pan/Tilt movement
3 zones of LED control
16 bit control of master dimmer and individual colors
Flicker-free operation
Overview

Dimensions

3. Setup
AC Power
The Q-Wash™ 419Z-LED has an auto-ranging power supply that works with an input
voltage range of 100~240 VAC, 50/60 Hz. To determine the power requirements for
each Q-Wash™ 419Z-LED, refer to the label affixed to the product. You can also
refer to the Technical Specifications section in this manual.
The listed current rating indicates the maximum current draw during normal
operation. For more information, you may download Sizing Circuit Breakers from the
CHAUVET® website: www.chauvetpro.com.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The Q-Wash™ 419Z-LED comes with a power input cord terminated with a Neutrik®
powerCON® A connector and an Edison power cord adapter. If the power cord
adapter that came with your product has no plug or you need to change the Edison
plug, use the table below to wire the new plug.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Power
Linking
The Q-Wash™ 419Z-LED supports power linking. You can power link up to:
5 products at 120 VAC,
9 products at 208 VAC, or
9 products at 230 VAC
This product comes with a power input cord. This product does not come with a
power linking cable; however, a power linking cable is available as an option.
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace the blown fuse with another of the same type and rating.
Fuse
Replacement
The stand-alone
battery charger has no
external fuse.
However, the flight
case/charger comes
with a replaceable
fuse (T 6.3 A @ 250
V).
To change the fuse on
the flight
case/charger, do the
following:
1. Disconnect
the product from the
power outlet.
2. With a
Phillips #2 head
screwdriver, unscrew

the fuse holder cap
from its housing.
3. Remove
the blown fuse and
replace it with a good
fuse of the same type
and rating (T 6.3 A @
250 V).
4. Screw the
fuse holder cap back
in its place and
reconnect power.
DMX Linking
You can link the Q-Wash™ 419Z-LED to a DMX controller using a standard DMX
serial connection. If using other DMX compatible products with the Q-Wash™
419Z-LED, you can control each individually with a single DMX controller.
DMX Modes
The Q-Wash™ 419Z-LED uses the standard DMX data connection for its
PERSON1, PERSON2, PERSON3, PERSON4, and PERSON5 DMX modes.
Refer to the Introduction section for a brief description of these modes.
Refer to the Operation section to learn how to configure the Q-Wash™
419Z-LED to work in these modes.
The DMX Values section provides you with detailed information
regarding the DMX modes.
Master/Slave
Connectivity
The Master/Slave mode allows a Q-Wash™ 419Z-LED (master product) to control
one or more products (slave products) without a DMX controller.
One Q-Wash™ 419Z-LED becomes the master product either when running in
static (MANUAL > MANUAL) mode or when using the automatic (STAND ALONE
> RUN > AUTO 1~2) or customizable (STAND ALONE > RUN > CUSTOM)
programs.
In addition, you must configure each of the slave products (via control panel) to
operate in Slave (STAND ALONE > RUN > SLAVE) mode. During Master/Slave
operation, the slave products will operate in unison with the master product.
For more information, see Menu Map.
Do not connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master product.
The Operation section of this manual provides detailed instructions on
how to configure the Master and Slave products.
If you need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed in order to link the product to a DMX
controller, download the DMX Primer from the CHAUVET® website:
www.chauvetpro.com.
Mounting
Before mounting this product, read and follow the Safety Notes.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.

Rigging
CHAUVET® recommends using the following general guidelines when mounting this
product.
When selecting an installation location, consider easy access to this product
for operation, programming adjustments, and routine maintenance.
Make sure to mount this product away from any flammable material as
indicated in the Safety Notes.
Never mount in places where rain, high humidity, extreme temperature
changes, or restricted ventilation may affect the product.
If hanging this product, make sure that the mounting location can support the
product’s weight. See the Technical Specifications for the weight-bearing requirements
of this product.
When hanging this product, always secure to a fastening device using a safety
cable (included).
Procedure
The Q-Wash™ 419Z-LED comes with two omega brackets to which you can attach
clamps. You must supply your own clamps and make sure that they are capable of
supporting the weight of this product. You will have to use two mounting points per
product. The omega brackets also serve to anchor this product to a panel. For floor
standing operation, this product has built-in rubber feet..
Mounting
Diagram
4. Operation

Control Panel
Description
Button
Function
MENU
Exits from the current menu or function
ENTER
Enables the currently displayed menu or sets the currently selected
value in to the current function
UP
Navigates upward through the menu options and increases the
numeric value when in a function
DOWN
Navigates downward through the menu options and decreases the
numeric value when in a function
Control Options
You can set the Q-Wash™ 419Z-LED starting address in the 001 to 512 DMX
range. This enables control of up to 15 products in the 34-channel PERSON5
personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map
shows the main level and a variable number of programming levels for each
option.
To go to the desired main level, press MENU repeatedly until the
option shows on the display. Press ENTER to select. This will take you to the
first programming level for that option.
To select an option or value within the current programming level,
press UP or DOWN until the option shows on the display. Press ENTER to
select. In this case, if there is another programming level, you will see that first
option, or you will see the selected value.
Press MENU repeatedly to exit to the previous main level.
Control Panel
Display
The Q-Wash™ 419Z-LED allows you to customize what is displayed on the
products control panel screen.
1. Choose the screen mode as follows.
a. Go to SETTINGS > PERFORM > HOME SCREEN.
b. Select DMX to display only the DMX address or NAME to display
what is programmed in the CONTENT level.
2. Enter the text to be displayed on the screen as follows.
a. Go to SERVICE > CONTENT.
b. Select DISPLAY1.
c. Use the UP and DOWN keys to enter up to 16 characters of text.
d. Select DISPLAY2.
e. Use the UP and DOWN keys to enter up to 16 characters of text.
Display Backlight
1. Select SETTINGS > PERFORM > DISPLAY ON.
a. Select LONG, SHORT, or ALWAYS.
Display Invert
1. Select SETTINGS > PERFORM > DISPLAY INVERT.
a. Select INVERT to reverse the display direction or NORM to use the
normal display direction.

Control Panel
Lock
This setting enables you to activate or disable the control panel lock, which keeps
non-authorized personnel from changing the product’s settings.
To secure the SETTINGS level only:
1. Go to SERVICE > ACCESS > SETTINGS LOCK.
a. Select ON to require the password to access the level or OFF to allow
open access.
To secure the SERVICE level only:
1. Go to SERVICE > ACCESS > SERVICE LOCK.
a. Select ON to require the password to access the level or OFF to allow
open access.
To secure all levels of the control panel:
1. Go to SETTINGS > DISPLAY LOCK.
a. Select ON to require the password to the control panel or OFF to allow
open access.
When the control panel lock is active, the product will prompt you to enter the
password after 30 seconds of control panel inactivity or after turning on the product.
Password
After being prompted to enter the password:
Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>
DMX
Personality
This setting allows you to choose a particular DMX personality.
1. Go to the PERSON main level.
2. Select the desired personality (PERSON1, PERSON2, PERSON3,
PERSON4, or PERSON5).
For the highest starting address you can select for each personality, see the DMX
Values section. Verify that the starting addresses on the products do not overlap due
to the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX
controller. All products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personality.
2. Set the running mode:
a. Go to the STAND ALONE > RUN main level.
b. Select the DMX 512 programming level.
3. Set the starting address:
a. Go to ADDRESS main level.
b. Select the starting address (001~512).
The highest recommended starting address for each DMX mode are as follows:
DMX Mode
DMX Address
DMX Mode
DMX Address
PERSON1
503
PERSON4
492
PERSON2
492
PERSON5
479
PERSON3
505

Loss of Signal
Setting
This setting controls how the product will respond when the DMX signal is
lost.
1. Go to the SETTINGS > PERFORM level, and select DMX
ERROR.
a. Select SAVE to make the product use the last command used
when the signal is lost.
b. Select BLACK to turn off the all the LEDs when the signal is lost.
Static Control
The Static Color mode allows for permanent RGBW color mixing without a
DMX controller.
1. Go to the MANUAL > MANUAL.
2. Select DIMMER.
a. Set the intensity value (000~255).
3. Select RED, GREEN, BLUE, or WHITE.
a. Select the color value (000~255).
b. Repeat for the other colors.
4. Select PAN or TILT.
a. Set the position value (000~255).
b. Repeat for the other position.
5. Select STROBE.
a. Set the frequency value (000~255).
6. Select ZOOM.
a. Set the angle value (000~255).
Auto/Custom
Programs
Auto programs allow for dynamic RGBW color mixing without a DMX
controller.
1. Go to STAND ALONE > RUN.
2. Select the desired auto (AUTO1, AUTO2), test (TEST), or
custom program (CUSTOM).
You cannot edit any of the auto or test programs (AUTO1, AUTO2, or
TEST).

Edit Custom
Programs
This setting allows the programming of up to 49 steps in the CUSTOM running
mode.
1. Go to STAND ALONE > EDIT.
2. Select STEP.
3. Set the program step (01~49).
a. Select PAN or TILT.
i. Set the position value (000~255).
ii. Repeat for the other position
b. Select DIMMER.
i. Set the intensity value (000~255).
c. Select RED, GREEN, BLUE, or WHITE.
i. Select the color value (000~255).
ii. Repeat for the other colors.
d. Select STROBE.
i. Set the frequency value (000~255).
e. Select ZOOM.
i. Set the angle value (000~255).
f. Select TIME.
i. Select the step duration (000~255).
g. Repeat for the other steps
4. Select USE.
a. Select YES to save the program or NO to discard.
Master/Slave
The Master/Slave mode allows a group of Q-Wash™ 419Z-LEDs (slave
products) to simultaneously duplicate the output of another Q-Wash™ 419Z-LED
(master product) without a DMX controller.
1. Set each of the slave products:
a. Go to STAND ALONE > RUN.
b. Select SLAVE.
2. Set the master product:
a. Set the running mode to DMX (see DMX Control).
b. Select an Auto, Custom, or Static program as explained in
Auto/Custom Programs or Static Control.
The master product is the one that runs a program whether in Auto,
Custom, or Static Color mode.
Do not connect a DMX controller to the products configured for
Master/Slave operation. The DMX controller may interfere with signals from the
master product.
The master product should be the first product in the daisy chain.

Fixture
Cloning
The Q-Wash™ 419Z-LED gives you 3 ways in which to transfer the settings from 1
Q-Wash™ 419Z-LED to other Q-Wash™ 419Z-LED products when hooked up via
DMX daisy chain configuration.
To transfer the CUSTOM program only:
1. Go to STAND ALONE > SEND.
a. Select YES to send the program or NO to cancel.
To transfer the CONTENT program (display text) only:
2. Go to SERVICE > CONTENT > SEND.
a. Select YES to send the program or NO to cancel.
To transfer all of the product’s software settings:
3. Go to SETTINGS > SEND.
a. Select YES to send the program or NO to cancel.
Do not upload the data from a Q-Wash™ 419Z-LED to a different product. The
other product may become inoperative.
Fan Control
The Q-Wash™ 419Z-LED allows you to adjust the fan speed of the product to allow
for quiet operation.
1. Go to SETTINGS > PERFORM > FANS.
a. Select SLOW, NORMAL, FAST, or AUTO.
In AUTO mode, the product controls the speed of the fan to allow for the most
efficient cooling while allowing maximum output. To prevent overheating, using any
other fan speed may reduce product output.
Pan/Tilt Speed
1. Select SETTINGS > PERFORM > PT SPEED.
a. Select FAST for fast movement or SLOW to use the normal speed.
Reverse Pan
Direction
1. Select SETTINGS > PERFORM > PAN INVERT.
a. Select INVERT to reverse the pan direction or NORM to use the normal
pan direction.
Reverse Tilt
Direction
1. Select SETTINGS > PERFORM > TILT INVERT.
a. Select INVERT to reverse the tilt direction or NORM to use the normal
tilt direction.
Optics Speed
1. Select SETTINGS > PERFORM > OPTICS SPEED.
a. Select FAST for fast movement or SLOW to use the normal speed.
Reverse
Dimmer
Direction
1. Select SETTINGS > PERFORM > DIM INVERT.
a. Select INVERT to reverse the dimmer direction or NORM to use the
normal dimmer direction.
Head Motion
Black Out
1. Select SETTINGS > PERFORM > BLACKOUT.
a. Select INSTANT to black out the output when the head tilts or pans, or
DELAY to keep the output on while the head moves.

Color
Settings
The Color setting determines how the product generates the white color based on various
RGB settings.
1. Go to the SETTINGS > PERFORM main level.
2. Select COLOR.
3. Select OFF, RGBtoW, or UC.
OFF:
When all the RGB faders are set to 255, the output is maximum, although the
resulting white color may not be balanced.
RGBtoW:
When all the RGB faders are set to 255, the resulting output is defined by the
configured White color (see White Calibration).
UC:
When all the RGB faders are set to 255, the output matches that of less
efficient products (Universal Color).
Dimmer
Curves
This setting provides you with four options to simulate the dimming curve of an
incandescent light product.
1. Go to the SETTINGS > PERFORM main level.
2. Select DIMMER.
3. Select the desired dimmer curve (OFF, DIM1, DIM2, DIM3, or DIM4).
OFF
The output is proportional (linear) to the dimmer and RGBW channel values.
DIM1~4:
The output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, being DIM1 the fastest and DIM4 the slowest.
Dimmer
Curve
Settings
This setting allows you to select the dimmer curve shape using the red, green, blue,
white, and dimmer faders.
1. Go to the SETTINGS > PERFORM main level.
2. Select CURV.
3. Select the desired dimmer curve (OFF, CURV1, CURV2, or CURV3).
OFF
This output is proportional (linear) to the Dimmer and RGBW channel values.
CV1~3
This output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, being CURV1 the fastest and CURV3 the slowest.
For optimum control of the 16-bit dimming channels in the PERSON2 and PERSON5
personalities, be sure that both dimming curves in SETTINGS > PERFORM > DIMMER
and SETTINGS > PERFORM > CURV are set to OFF
Zoom
Position
Adjust
This setting adjusts the position of the zoom lens outside the normal limits to allow
for tighter beam adjustment at longer distances.
1. Select SETTINGS > PERFORM > ZOOM POS.
a. Select BOOST to adjust the zoom lens for better focusing at longer
distances or NORMAL to use the factory settings.

Limit Pan/Tilt
Range
1. Select SETTINGS > RANGE.
2. To set the start and end points of the pan and tilt ranges:
a. Select P.START and set the pan starting point between 000~255.
b. Select P.END and set the pan ending point between 000~255.
c. Select T.START and set the tilt starting point between 000~255.
d. Select T.END and set the tilt ending point between 000~255.
3. Select USE.
a. Select YES to activate the changes or NO to cancel.
Offset
Calibration
This option allows you to calibrate the starting points of the Pan, Tilt, and Zoom
motors.
1. Select SERVICE > CALIB.M.
a. Select PAN.
i. Set the position value (000~255).
b. Select TILT.
i. Set the position value (000~255).
c. Select ZOOM.
i. Set the position value (000~255).
White
Calibration
This setting allows you to select and edit the temperature of the white colors used in
channel 14 (Macros) when in the PERSON2 mode.
1. Select SERVICE > CALIB.C.
2. Select 3200K, 3400K, 4200K, 4900K, 5600K, 5900K, 6500K, 7200K,
8000K, 8500K, or 10000K.
3. Select RED, GREEN, BLUE, or WHITE.
a. Set the position value (000~255).
b. Repeat for the other colors.
4. Repeat for other color temperatures.
Calibrating
the
White Color
This setting allows you to calibrate the white color when SETTINGS > PERFORM >
COLOR is set to RGBtoW and the DMX controller’s red, green, and blue faders are
set to “255”.
1. Select SERVICE > CALIB.C.
2. Select RGBTOW
3. Select RED, GREEN, or BLUE.
a. Set the position value (000~255).
b. Repeat for the other colors.
When selecting SERVICE > CALIB.C > RGBTOW, you will only be able to define
the values of red, green, and blue.
The values of RED, GREEN, and BLUE configured from SERVICE > CALIB.C >
RGBTOW will define the color temperature shown when the RGB faders are set to
“255” if SETTINGS > PERFORM > COLOR > RGBtoW is active.
Product Reset
Control
This option allows the product to be reset from the DMX controller or from the
display only.
1. Select SETTINGS > PERFORM > DMX RESET.
a. Select DMX to reset the product from a DMX controller or DISPLAY
to reset the product from the control panel only.