Chauvet Q-Spot 160-LED User manual

User Manual

Edition Notes
Q-Spot™ 160-LED User Manual Rev. 01b
Edition Notes
The Q-Spot™ 160-LED User Manual Rev. 01b
covers the description, safety
precautions, installation, programming, operation, and maintenance of the Q-Spot™
160-LED product. CHAUVET® released this edition of the Q-Spot™ 160-LED User
Manual Rev. 01b in September 2010.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and the
dotted triangle, and all other trademarks on this manual pertaining to services, products
or marketing statements (example: It’s Green Thinking™) are owned or licensed by
CHAUVET®. Any other product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this user manual in its entirety, including but not limited
to pictures, logos, trademarks, and resources.
© Copyright 2010 CHAUVET®. All rights reserved
Electronically published by CHAUVET® in the United States of America
Manual Usage
CHAUVET® authorizes its customers to download and print this manual for professional
information purposes only. CHAUVET® expressly prohibits the usage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purpose
without its written consent.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 inches),
double sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content of this document to A4 paper.
Intended Audience
Any person in charge of installing, operating, and/or maintaining the Q-Spot™ 160-LED
should read the Guide that shipped with it as well as this manual in their entirety before
installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any error or omissions
in this document. CHAUVET® reserves the right to revise this document and to make
changes from time to time in the content hereof without obligation of CHAUVET® to
notify any person or company of such revision or changes. This does not constitute in
any way a commitment by CHAUVET® to make such changes. CHAUVET® may issue
a revision of this manual or a new edition of it to incorporate such changes.
CHAUVET®
Publications Hot
Line
If you have any comments about the accuracy of this document or general suggestions
regarding how we can improve it, please call us at [phone] (US callers) or +1-
954-929-1115 (international callers). You can download the latest versions of all
CHAUVET® products’ manuals from www.chauvetlighting.com.
Document
Revision
The Q-Spot™ 160-LED User Manual Rev. 01b supersedes all previous versions of this
manual. Please discard any older versions of this manual you may have, whether in
printed or electronic format, and replace them with this version.
Author Editor Manager PD Manager
O. Desmonteix D. Couppe M. Graham F. Sellers
Product at
a Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle


Table of Contents
Q-Spot™ 160-LED User Manual Rev. 01b -a-
Table of Contents
1. Before You Begin............................................................................................................1
What is Included.............................................................................................................................1
Unpacking Instructions ...................................................................................................................1
Typographic Conventions...............................................................................................................1
Icon Meaning..................................................................................................................................1
Safety Notes...................................................................................................................................2
Expected LED Lifespan..................................................................................................................2
2. Introduction.....................................................................................................................3
Product Description........................................................................................................................3
Features.........................................................................................................................................3
Additional Features....................................................................................................................................3
DMX Channel Summary.................................................................................................................3
Product Overview...........................................................................................................................4
3. Setup................................................................................................................................5
AC Power.......................................................................................................................................5
AC Plug.....................................................................................................................................................5
Fuse Replacement.....................................................................................................................................5
DMX Linking...................................................................................................................................6
DMX Modes...............................................................................................................................................6
Master/Slave Connectivity..........................................................................................................................6
Color Wheel ...................................................................................................................................6
Gobo Wheel...................................................................................................................................7
Gobo Replacement.........................................................................................................................7
Mounting........................................................................................................................................8
Orientation.................................................................................................................................................8
Rigging......................................................................................................................................................8
4. Operation.........................................................................................................................9
Control Panel Description...............................................................................................................9
Control Options ..............................................................................................................................9
Programming..................................................................................................................................9
DMX Operation..........................................................................................................................................9
Auto Programs...........................................................................................................................................9
Sound Programs........................................................................................................................................9
Custom Program........................................................................................................................................9
Master/Slave............................................................................................................................................10
Display Backlight......................................................................................................................................10
System Info .............................................................................................................................................10
Fixture Reset...........................................................................................................................................10
Reset Control...........................................................................................................................................10
Move-in-Black..........................................................................................................................................10
Movement Ranges...................................................................................................................................11
Movement Modifications...........................................................................................................................11
Edit Custom.............................................................................................................................................12
Menu Map....................................................................................................................................13
DMX Values.................................................................................................................................14
Basic Mode..............................................................................................................................................14
Advanced Mode.......................................................................................................................................15
5. Technical Information...................................................................................................16
General Maintenance...................................................................................................................16
Photometrics................................................................................................................................16
Troubleshooting Guide .................................................................................................................17
Returns Procedure .......................................................................................................................18

Table of Contents
-b- Q-Spot™ 160-LED User Manual Rev. 01b
Claims..........................................................................................................................................18
Contact Us....................................................................................................................................18
Technical Specifications................................................................................................................19

Before You Begin
Q-Spot™ 160-LED User Manual Rev. 01b -1-
1. Before You Begin
What is
Included
•One Q-Spot™ 160-LED
•Two mounting brackets
•One power cord
•Three extra gobos
•Warranty Card
•Quick Start Guide
Unpacking
Instructions
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above
and that they are all in good condition. If the material inside the container (this product
and any other accessory included with it) appears damaged from shipping, or if the
container shows signs of mishandling, notify the shipper immediately. In addition, retain
the container and all the packing material for inspection.
See the Claims section in the Technical Information chapter.
Typographic
Conventions
Convention Meaning
1~512 A range of values in the text
50/60 A set of mutually exclusive values in the text
[10] A DIP switch to be configured
Claims A new term, or a section or chapter in this document
“COLORado™ UM” The name of another publication or manual
<SET> A button on thefixture’s control panel
Settings A fixture function or a menu option
MENU > Settings
A sequence of menu options
1~10 A range of menu values from which to choose in a menu
Yes/No A set of two mutually exclusive menu options in a menu
ON
A unique value to entered or select in a menu
Icon Meaning
Icon Meaning
This icon indicates critical installation, configuration, or operation
information. Failure to comply with this information may render
the fixture partially or completely inoperative, damage third-party
equipment, or cause harm to the user.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the fixture from functioning correctly.
This icon indicates useful, although non-critical information.
The term “DMX” used throughout this document refers to the USITT DMX512-A
transmission protocol.

Before You Begin
-2- Q-Spot™ 160-LED User Manual Rev. 01b
Safety Notes Please read the following notes
carefully because they include important safety
information about the installation, usage, and maintenance of this product.
It is important to read all these notes before starting to work with this product.
There are no user serviceable parts inside this product. Any reference to
servicing it you may find from now on in this User Manual will only apply to
properly CHAUVET® certified technicians. Do not open the housing or attempt
any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for the proper
installation of this product.
Keep this manual for future consultation. If you sell this product to another user,
make sure that they also receive this manual.
Personal Safety
•Avoid direct eye exposure to the light source while the fixture is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing when operating because it could be hot.
Mounting and Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose
this product to rain or moisture.
•This product is for outdoor use (IP66). However, do not submerge it.
•This product is for outdoor use and it can be submerged (IP67). However, do not
submerge it deeper than 1 m.
•This product weighs XX lbs (XX kg). Always ask for help when mounting this
product to avoid personal injuries or damage to the unit.
•Make sure there are no flammable materials close to this product while operating.
•When hanging this product, always secure it to a fastening device using a safety
cable (not provided).
•Do not carry this fixture from the head; carry it from the base instead.
Power and Wiring
•Always make sure that you are connecting this product to the proper voltage, as
per the specifications in this manual or on the product’s sticker.
•Never connect this product to a dimmer pack or rheostat.
•Make sure the product’s housing or power cable are not cracked, crimped, or
damaged.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this fixture if you see damage on the housing, lenses, ultraviolet
filter, or cables; have the damaged parts replaced by an authorized technician at
once.
•Do not cover the ventilation slots when the fixture is operating to avoid internal
overheating.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at a higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, please
contact CHAUVET® Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal or singular optimum
conditions. For this reason, using all color LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be of 40,000 to
50,000 hours. If extending this lifespan expectancy is vital, lower the operational
temperature by improving fixture ventilation and reducing the external temperature. In
addition, limiting the overall projection intensity may also help to extend the LEDs life.

Introduction
Q-Spot™ 160-LED User Manual Rev. 01b -3-
2. Introduction
Product
Description
The Q-Spot™ 160 LED is a hard edge 9- or 12-channel DMX yoke with a nine-step
color wheel plus white. It features a 7-position rotating slot-and-lock gobo wheel with an
easy-to-open cover and a three-facet prism.
Features
•9 or 12-channel DMX LED moving yoke
•Pan: 540º
•Tilt: 270º
•Color Wheel
Nine colors + white
Rainbow color spins at variable speeds
•Gobo wheel with gobo shake
Seven interchangeable, slot-n-lock, rotating gobos + open
Gobo wheel spins at variable speeds
•One high-powered, 20 W (1,000 mA) LED
•One 3-facet prism
•Variable electronic strobe
•Variable electronic dimmer (0~100%)
•Remote fixture reset & vector speed channel
•Up to 255 user-programmable steps without DMX controller
•Move-in-black for pan/tilt
•Built-in automated programs
•Built-in sound activated programs
Additional Features
•Three extra gobos
•User-selectable pan/tilt ranges
•Automatic pan/tilt correction
•Reset to factory settings option
•User-selectable basic or advanced operating modes
DMX Channel
Summary
The Q-Spot™ 160 LED has two DMX modes, Basic (9 channels) and Advanced (12
channels). The table below shows the functions assigned to each channel in these
DMX modes.
Basic Mode Advanced Mode
DMX Channel Function DMX Channel Function
1 Pan 1 Pan
2
Tilt
2
Pan fine
3
Color
3
Tilt
4
Gobo
4
Tilt fine
5 Gobo Rotation 5 Pan/tilt speed
6 Prism 6 Color
7 Dimmer 7 Gobo
8 Strobe 8 Gobo Rotation
9 Control 9 Prism
10 Dimmer
11 Strobe
12 Control

Introduction
-4- Q-Spot™ 160-LED User Manual Rev. 01b
Product Overview
DMX Out
Power Input/Fuse holder
DMX In
On/Off Switch
Fan
Control Panel
Gobo cover
NOTE: Dimension in inches rounded to the nearest decimal digit

Setup
Q-Spot™ 160-LED User Manual Rev. 01b -5-
3. Setup
AC Power This product has an auto-ranging power supply that can work with an input voltage
range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting the Q-Spot™ 160-LED to the proper voltage, as per
the specifications in this guide, the product’s manual or on the product’s sticker.
Always connect the Q-Spot™ 160-LED to a protected circuit with an appropriate
electrical ground to avoid the risk of electrocution or fire.
To determine the power requirements for the Q-Spot™ 160-LED
see the label affixed to
the side of the fixture. Alternatively, you may refer to the corresponding
specifications
chart in the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download the “Sizing the Circuit Breakers” document
from the CHAUVET® Web site.
Never connect the Q-Spot™ 160-LED to a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The Q-Spot™ 160-LED comes with a power input cord terminated with an Edison plug
(US market). If the power cord that came with your fixture has no plug or you need to
change the Edison plug, use the table below to wire the new plug.
Connection Wire (US) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
Make sure to disconnect the fixture’s power cord before replacing a blown fuse,
and always replace it with a fuse of the same type and rating.
Fuse Replacement 1) With a flat head screwdriver, wedge the fuse holder out of its housing and remove
the blown fuse from its holder.
2) Replace the blown fuse with a fuse of the exact same type and rating.
3) Insert the fuse holder back in its place, and reconnect power.
The fuse is located
inside this compartment.
Remove it as instructed
above.
Power Input
On/Off Switch

Setup
-6- Q-Spot™ 160-LED User Manual Rev. 01b
DMX Linking
You may link any Q-Spot™ 160-LED fixture to a DMX controller using a standard DMX
serial connection. If using other DMX compatible fixtures with a Q-Spot™ 160-LED
fixture, it is possible to control them individually with a single DMX controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the Q-Spot™ 160-LED fixture to a DMX controller, you may
download the “DMX Primer” document from the CHAUVET® Web site.
DMX Modes
The Q-Spot™ 160-LED uses the standard DMX data connection for its **DMX mode(s),
<list of modes>**. You will find information about these DMX modes in the Introduction
chapter (brief description), the Operation Instructions chapter (configuration details), and
the DMX Values section (individual channel values).
Master/Slave
Connectivity
The Master/Slave mode allows a Q-Spot™ 160-LED fixture to control one or more Q-
Spot™ 160-LED fixtures without a DMX controller. The controlling fixture becomes the
“master” when running an Auto program (AUTO 1 or 2), a sound activated program
(SOUND 1 or 2), or the custom program (CUSTOM). The controlled fixtures are the
“slaves” and you must set them to “Slave” mode from their respective control panels.
During the Master/Slave operation, the slave fixtures will operate in unison with the
master fixture.
The master and slave fixtures link to each other using the standard DMX serial
connection. If you are not familiar with the Master/Slave connectivity, you may download
the “DMX Primer” document from the CHAUVET® Web site.
DO NOT connect a DMX controller to the fixtures operating in Master/Slave mode.
Otherwise, the signals from the DMX controller may interfere with the signals from
the master unit.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave units.
Color Wheel
The Q-Spot™ 160-LED comes equipped with a Color wheel featuring nine colors and a
white (open).
Color Wheel Diagram

Setup
Q-Spot™ 160-LED User Manual Rev. 01b -7-
Gobo Wheel
The Q-Spot™ 160-LED comes equipped with a gobo wheel featuring seven rotating and
replaceable (slot-n-
lock system) gobos. The gobo wheel has an eighth position with no
gobo (open).
Gobo Wheel Diagram
Gobo
Replacement
The Q-Spot™ 160-LED features a gobo wheel that holds seven interchangeable, slot-n-
lock gobos. These gobos can rotate at various speeds and in both directions.
Follow the procedure below to change any of the gobos on the gobo wheel
Always disconnect the fixture from the AC power before opening it.
Procedure
1) Remove the gobo cover.
2) Remove the slot-n-lock gobofrom the gobo wheel.
3) Using a small tool, pry the tension ring from the gobo holder.
4) Remove the old gobo.
5) Insert the new gobo, and replace in the reverse steps of removal.
If using coated glass gobos, make sure that the more reflective side of the gobo
(glass base) faces the light source. This way, the glass base of the gobo will
provide extra isolation to its coating from the heat of the light source, thus
minimizing the risk of damaging the gobo’s coating.
Gobo Replacement
Diagram
Gobo
Sliding knob
Gobo cover

Setup
-8- Q-Spot™ 160-LED User Manual Rev. 01b
Mounting
Before mounting this fixture, read and follow the safety recommendations indicated in
the Safety Notes section (page 2 of this manual).
Orientation
Always mount this fixture in any safe position while making sure that there is adequate
room around it for ventilation, configuration, and maintenance.
Rigging CHAUVET® recommends following the general guidelines below when mounting the Q-
Spot™ 160-LED.
•When selecting an installation location, consider ease of access to the fixture for
operation, programming adjustments, and routine maintenance.
•Make sure to mount this fixture away from any flammable material as indicated in
the Safety Notes section.
•Never mount the fixture in places where rain, high humidity, extreme temperature
changes, or restricted ventilation may affect it.
•If hanging this fixture, make sure that the location where you are mounting the
fixture can support its weight. Please see the Technical Specifications section of this
manual for the weight requirement of this fixture.
Procedure
You can mount the Q-Spot™ 160-LED on a flat, rigid surface or hang it from a truss.
This fixture includes two mounting brackets for overhead mounting. You can attach a
rigging clamp to . You must supply your own “C” or “O” clamps as well as your safety
cable, making
sure that they are capable of supporting the weight of this fixture. You
need to use two clamps per fixture.
Product Mounting
Diagram
C clamp
(not provided)
Safety cable
(not provided)
Mounting
brackets
(included)

Operation
Q-Spot™ 160-LED User Manual Rev. 01b -9-
4. Operation
Control Panel
Description
Button Function
<MENU> Exits from the current menu or
function
<ENTER>
Enables the currently displayed
menu or sets the currently
selected value in to the current
function
<DOWN> Navigates downwards through
the menu list and decreases the
numeric value when in a function
<UP> Navigates upwards through the
menu list and increases the
numeric value when in a function
Control Options You can set the Q-Spot™ 160-LED start address in the 001~512 DMX range. This
allows for the control of up to 42 fixtures in the 12-channel Advanced DMX mode.
Programming
Carry out all the programming procedures indicated below from the control panel. Refer
to the Menu Map on page 13 to learn how the menu options relate to each other.
To go to an option, press <MENU> repeatedly until the option shows on the display.
To select an option value, press <UP> or <DOWN> until you see the desired value and
press <ENTER> to accept it.
To exit to the previous menu level, press <MENU>.
DMX Operation
1) Go to Intro > Run.
a) Select DMX-512.
b) Activate the DMX operation mode or return to the previous level.
2) Go to Intro > Address.
a) Select the starting address (001~512).
b) Activate the new DMX address or return to the previous level.
3) Go to Intro > Channels.
a) Select either Advanced (12 channels) or Basic (9 channels).
b) Activate the selected DMX mode or return to the previous level.
When selecting the Advanced mode, you can accommodate up to 42 Q-Spot™
160-LED fixtures on the same DMX universe.
Auto Programs
1) Go to Intro > Run.
2) Select Auto 1 or Auto 2.
3) Activate the selected AUTO program or return to the previous level.
Sound Programs 1) Go to Intro > Run.
2) Select Sound 1 or Sound 2.
3) Activate the selected SOUND program or return to the previous level.
Custom Program
1) Go to Intro > Run.
2) Select Custom.
3) Activate the CUSTOM program or return to the previous level.
See Edit Custom to learn how to configure the 255 steps of the CUSTOM program.
Continues on the next page

Operation
-10- Q-Spot™ 160-LED User Manual Rev. 01b
Continued from previous page
Master/Slave 1) On the master unit, go to Intro > Operation.
a) Select any suitable Auto or Sound program.
b) Activate the selected AUTO or SOUND program.
2) On each of the slave units, go to Intro > Operation.
a) Select Slave.
b) Activate the SLAVE mode or return to the previous level.
Display Backlight
1) Go to Intro > Display.
2) Select
60 Close (the backlight will turn off after 60 seconds of control panel inactivity) or
Bright (the backlight will stay on permanently).
3) Activate the selected backlight operation or return to the previous level.
System Info
1) Go to Intro > Info.
2) Select Edition (the firmware version will show on the display).
3) Accept or return to the previous level.
Fixture Reset
1) Go to Intro > Reset.
2) Select
Yes (all custom modifications will be lost) or
No (all custom modifications will remain).
3) Accept or return to the previous level.
Reset Control
1) Go to Special > Reset.
2) Select
DMX (the fixture will accept reset commands from the DMX controller) or
System (the fixture will only reset from the control panel).
3) Accept or return to the previous level.
Move-in-Black
1) Go to Special > Black.
2) Select
No (move-in-black will stay active for as long as the Control channel remains
between 020~039) or
Yes (move-in-black will activate permanently if the Control channel remains
between 020~039 for 3 seconds.
3) Accept or return to the previous level.
Once Move-in-Black is permanently active, it will deactivate if the Control channel
remains between 040~059 for 3 seconds.
Continues on the next page

Operation
Q-Spot™ 160-LED User Manual Rev. 01b -11-
Continued from previous page
Movement Ranges 1) Go to Range.
2) Set the start point of the PAN movement.
a) Select P/Start.
b) Select a value (000~255).
c) Activate the new value.
3) Set the end of the PAN movement.
a) Select P/Finish.
b) Select a value (000~255).
c) Activate the new value.
4) Set the start point of the TILT movement.
a) Select T/Start.
b) Select a value (000~255).
c) Activate the new value.
5) Set the end of the TILT movement.
a) Select T/Finish.
b) Select a value (000~255).
c) Activate the new value.
6) Activate/disable the movement ranges.
a) Select Use.
b) Select
No (full range movement) or
Yes (limited range movements).
c) Activate the new setting.
Movement
Modifications
1) Go to Invert.
2) Reverse the direction of the PAN movement (540º~0).
a) Select Pan.
b) Select No (0~540º) or Yes (540~0º).
c) Activate the new setting.
3) Reverse the direction of the TILT movement (270º~0).
a) Select Tilt.
b) Select
No (0~270º) or
Yes (270~0º).
c) Activate the new setting.
4) Change the way the COLOR wheel rotates.
a) Select Color.
b) Select
Step (the color wheel jumps from one color to the next) or
Linear (the color wheel rotates smoothly from one color to the next to allow for
rainbow effects).
c) Activate the new setting.
5) Activate/disable the movement modifications.
a) Select Use.
b) Select
No (use normal settings) or
Yes (use modified settings)
c) Press <ENTER>to activate the new setting.
Continues on the next page

Operation
-12- Q-Spot™ 160-LED User Manual Rev. 01b
Continued from previous page
Edit Custom 1) Go to Edit.
2) Select Step.
a) Select a step number (000~255).
b) Activate the new value.
3) Select Pan.
a) Select a pan position (000~255).
b) Activate the new value.
4) Select Tilt.
a) Select a tilt position (000~255).
b) Activate the new value.
5) Select Speed.
a) Select a movement (pan & tilt) speed (000~255).
b) Activate the new value.
6) Select Color.
a) Select a color from the color wheel (000~255).
b) Activate the new value.
7) Select Gobo.
a) Select a gobo from the gobo wheel (000~255).
b) Activate the new value.
8) Select Gobo.rot.
a) Select a rotation mode for the selected gobo (000~255).
b) Activate the new value.
9) Select Prism.
a) Select a prism operation mode (000~255).
b) Activate the new value.
10) Select Dimmer.
a) Select a dimmer value (000~255).
b) Activate the new value.
11) Select Strobe.
a) Select a strobe mode (000~255).
b) Activate the new value.
12) Select Time.
a) Select the duration of this step (000~255).
b) Activate the new value.
13) Select Use.
a) Enable this step (Yes/No).
b) Activate the new value.
14) Repeat for the other steps.
For smoother operation of the CUSTOM program, disable all the steps that are not
part of the program (Use = No).
The fixture will execute all the steps in the CUSTOM program and it will stop.
To make the fixture to start over add a last step whose duration is 0 seconds.
Example:
Step 1: Time = 5 Use = Yes
Step 2: Time = 4 Use = Yes
Step 3: Time = 6 Use = Yes
Step 4: Time = 0 Use = Yes (This step creates a loop)
Step 5: Time = 0 Use = No
(Unused steps)
Step 255 Time = 0 Use = No

Operation
Q-Spot™ 160-LED User Manual Rev. 01b -13-
Menu Map
1st Level 2nd Level 3rd Level Description
1-Intro
Address
001~512
Sets the DMX starting address
Reset
Yes/No
Resets the fixture to the “home” position
Run
DMX-512
Sets the fixture to DMX mode
Auto 1
Starts the hanging auto mode (pointing down)
Auto 2
Starts the floor standing auto mode (for placing on speaker)
Sound 1
Starts the hanging sound mode (pointing down)
Sound 2
Starts the floor standing sound mode (for placing on speaker)
Custom
Runs the user’s program
Test
Runs a standard test program
Slave
The fixture responds to a master unit
Channels
Advanced
16-bit pan/tilt operation
Basic
8-bit pan/tilt operation
Display
60 close
Turns the display backlight off after 60 seconds of being idle
Bright
Sets the display backlight to remain on indefinitely
Info
Edition
Shows the software version
2-Invert
Pan
Normal
Sets the Pan operation: 0~540º
Reverse
Reverses the Pan operation: 540~0º
Tilt
Normal
Sets the Pan operation: 0~270º
Reverse
Reverses the Pan operation: 270~0º
Color
Step
Sets the color wheel channel to locking colors
Linear
Allows split color operation on the color wheel channel
Use
No/Yes
Enables / disables all Invert functions
3-Range
P/start
000~255
Sets the Pan starting range
P/Finish
000~255
Sets the Pan end range
T/start
000~255
Sets the Tilt starting range
T/Finish
000~255
Sets the Tilt end range
Use
No/Yes
Enables / disables all Range functions
4-Special Black
No
Move-in-black is active only when
Control
channel =
020~039
Yes
Move-in-black activates permanently if Control channel = 020~039
for 3 seconds. (requires Control channel = 040~059 to deactivate it)
Reset
DMX
Allows the reception of a DMX remote reset command
System
Disables the reception of a DMX remote reset command
5-Edit
Step
000~255
Selects which step to edit
Pan
000~255 Use the nine different attributes of the fixture to create a custom step
(repeat for the other steps)
Tilt
X/Y_Speed
Color
Gobo
Gobo_Rot
Prism
Dimmer
Strobe
Time
000~255
Selects the duration of the step
Use
No/Yes
Enables / disables the program step
6-Default
Default
No/Yes
Defaults the fixture and erases the custom programs

Operation
-14- Q-Spot™ 160-LED User Manual Rev. 01b
DMX Values
Basic Mode
Channel Function Value Percent/Setting
1
Pan
000

255
0~540°
2
Tilt
000

255
0~270°
3 Color
000

014
015 029
030 044
045 059
060 074
075 089
090 104
105 119
120 134
135 149
150

255
White (open)
Red
Yellow
Green
Pink
Blue
Orange
Magenta
Light blue
Light green
Rainbow and linear effect (slow~fast)
4 Gobo
000

009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 099
100 119
120 139
140 159
160 179
180 199
200 219
220

255
No gobo (open)
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo shake 7
Gobo shake 6
Gobo shake 5
Gobo shake 4
Gobo shake 3
Gobo shake 2
Gobo shake 1
Gobo scroll (slow~fast)
5 Gobo Rotation
000 002
003 006
007 128
129 132
133 136
137

255
No function
Clockwise (slowest)
Clockwise (slow~fast)
No function
Counter-clockwise (slowest)
Counter-clockwise (slow~fast)
6 Prism 000 127
128

255
No function
3-facet prism
7
Dimmer
000

255
Closed

Open
8 Strobe
000

031
032 063
064 095
096 127
128 159
160 191
192 223
224

255
Closed
Open
Strobe (slow~fast)
Open
Pulse Strobe (slow~fast)
Open
Random Strobe (slow~fast)
Open
9
Control (hold
each of these
for 3
s to trigger
function)
000 019
020 039
040 059
060 079
080 099
100 119
120 139
140 159
160 179
180 199
200 219
220 255
No function
Pan/tilt move-in-black (activate)
Pan/tilt move-in-black (deactivate)
Auto 1
Auto 2
Sound 1
Sound 2
Custom
Test
No function
Reset
No function

Operation
Q-Spot™ 160-LED User Manual Rev. 01b -15-
Advanced Mode
Channel Function Value Percent/Setting
1
Pan
000

255
0~540°
2
Pan fine
000

255
Fine pan adjustment
3
Tilt
000

255
0~270°
4
Tilt fine
000

255
Fine tilt adjustment
5
Pan/tilt speed
000

255
Normal~slow
6 Color
000 014
015 029
030 044
045 059
060 074
075 089
090 104
105 119
120 134
135 149
150

255
White (open)
Red
Yellow
Green
Pink
Blue
Orange
Magenta
Light blue
Light green
Rainbow and linear effect (slow~fast)
7 Gobo
000 009
010 019
020 029
030 039
040 049
050 059
060 069
070 079
080 099
100 119
120 139
140 159
160 179
180 199
200 219
220

255
No gobo (open)
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo shake 7
Gobo shake 6
Gobo shake 5
Gobo shake 4
Gobo shake 3
Gobo shake 2
Gobo shake 1
Flow effect
8 Gobo Rotation
000 002
003 006
007 128
129 132
133 136
137

255
No function
Clockwise (slowest)
Clockwise (slow~fast)
No function
Counter-clockwise (slowest)
Counter-clockwise (slow~fast)
9 Prism 000 127
128

255
No function
3-facet prism
10
Dimmer
000

255
0~100% (closed~open)
11 Strobe
000

031
032 063
064 095
096 127
128 159
160 191
192 223
224 255
Closed
Open
Strobe (slow~fast)
Open
Pulse Strobe (slow~fast)
Open
Random Strobe (slow~fast)
Open
12
Control
(Hold each of
these for 3 s to
trigger function)
000 019
020 039
040 059
060 079
080 099
100 119
120 139
140 159
160 179
180 199
200 219
220

255
No function
Pan/tilt move-in-black activation
Pan/tilt move-in-black deactivation
Auto 1
Auto 2
Sound 1
Sound 2
Custom
Test
No function
Reset
No function

Technical Information
-16- Q-Spot™ 160-LED User Manual Rev. 01b
5. Technical Information
General
Maintenance
To maintain optimum performance and minimize wear, the user should clean the light
fixtures frequently. Usage and environment are contributing factors in determining the
cleaning frequency. As a rule, the user should clean the fixtures at least twice a month.
Dust build up reduces light output performance and can cause overheating. This can
lead to reduced light source life and increased mechanical wear.
CHAUVET® recommends cleaning the fixture’s external optics with a soft cloth using
normal glass cleaning fluid.
To clean a fixture, follow the recommendations below:
•Unplug the fixture from power.
•Wait until the fixture is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected
on the external vents and reachable internal components.
•Clean all external optics and glass surfaces with a mild solution of glass cleaner or
isopropyl alcohol, and a soft, lint free cotton cloth or a lens cleaning tissue.
•Apply the solution directly to the cloth or tissue and drag any dirt and grime to the
outside of the lens.
•Gently polish the external glass surfaces until they are free of haze and lint.
•When cleaning units with a movable mirror, you should keep the contact with the
mirror surface to a minimum to avoid scratching or damaging it.
Always dry the external optics and glass surfaces carefully after cleaning them.
If the fixture has one or more fans, refrain from spinning them using compressed
air.
Photometrics