Chauvet Lrgrnd 300E Beam User manual

User Manual

Edition Notes
Legend 300E Spot User Manual Rev. 01g
Edition Notes
The Legend 300E Spot User Manual Rev. 01g covers the description, safety
precautions, installation, programming, operation, and maintenance of the Legend
300E Spot. CHAUVET® released this edition of the Legend 300E Spot User Manual
Rev. 01g in December 2010.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and the
dotted triangle, and all other trademarks on this manual pertaining to services,
products, or marketing statements (example: It’s Green Thinking™) are owned or
licensed by CHAUVET®. Any other product names, logos, brands, company names,
and other trademarks featured or referred to within this document are the property of
their respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this user manual in its entirety, including but not
limited to pictures, logos, trademarks, and resources.
© Copyright 2010 CHAUVET®
All rights reserved
Electronically published by CHAUVET® in the United States of America
Manual Usage
CHAUVET® authorizes its customers to download and print this manual for
professional information purposes only. CHAUVET® expressly prohibits the usage,
copy, storage, distribution, modification, or printing of this manual or its content for any
other purpose without its written consent.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 inches),
double sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content of this document to A4 paper.
Intended Audience
Any person in charge of installing, operating, and/or maintaining the Legend 300E Spot
should read the guide that shipped with it and this manual in their entirety before
installing, operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any error or omissions
in this document. CHAUVET® reserves the right to revise this document and to make
changes from time to time in the content hereof without obligation of CHAUVET® to
notify any person or company of such revision or changes. This does not constitute in
any way a commitment by CHAUVET® to make such changes. CHAUVET® may issue
a revision of this manual or a new edition of it to incorporate such changes.
CHAUVET®
Publications Hot
Line
If you have any comments about the accuracy of this document or general suggestions
regarding how we can improve it, please call us at [phone] (US callers) or +1-
954-929-1115 (international callers). You can download the latest versions of all
CHAUVET® products’ manuals from www.chauvetlighting.com.
Document
Revision The Legend 300E Spot User Manual Rev. 01g supersedes all previous versions of this
manual. Please discard any older versions of this manual you may have, whether in
printed or electronic format, and replace them with this version.
Author Editor Manager PD Manager
O. Desmonteix D. Couppe M. Graham F. Sellers
Product at
a Glance
Use on Dimmer
x
Auto Programs
x
Outdoor Use
x
Auto-ranging Power Supply
P
Sound Activated
x
Replaceable Fuse
P
DMX
P
User Serviceable
x
Master/Slave
x
Duty Cycle
x

Table of Contents
Legend 300E Spot User Manual Rev. 01g -a-
Table of Contents
1. Before You Begin............................................................................................................1
What is Included.............................................................................................................................1
Unpacking Instructions ...................................................................................................................1
Typographic Conventions...............................................................................................................1
Icon Meaning..................................................................................................................................1
Safety Notes...................................................................................................................................2
2. Introduction.....................................................................................................................3
Product Description........................................................................................................................3
Features.........................................................................................................................................3
Additional Features....................................................................................................................................3
Options......................................................................................................................................................3
DMX Channel Summary.................................................................................................................4
Mode 1......................................................................................................................................................4
Mode 2......................................................................................................................................................4
Product Overview...........................................................................................................................5
3. Setup................................................................................................................................6
AC Power.......................................................................................................................................6
AC Plug.....................................................................................................................................................6
Fuse Replacement.....................................................................................................................................6
DMX Linking...................................................................................................................................6
DMX Modes...............................................................................................................................................6
Gobo Wheels..................................................................................................................................7
Extra Gobos...................................................................................................................................7
Color Wheel ...................................................................................................................................7
Gobo Replacement.........................................................................................................................8
Lamp Replacement ........................................................................................................................9
Increasing the Lamp’s Life..........................................................................................................................9
Mounting......................................................................................................................................10
Orientation...............................................................................................................................................10
Rigging....................................................................................................................................................10
4. Operation.......................................................................................................................11
Control Panel Description.............................................................................................................11
LCD Display.................................................................................................................................11
Control Options ............................................................................................................................11
Programming................................................................................................................................11
Navigation Buttons...................................................................................................................................11
DMX Functions........................................................................................................................................12
Fixture Settings........................................................................................................................................13
Lamp Settings..........................................................................................................................................14
Display Settings.......................................................................................................................................15
Fixture Tests............................................................................................................................................15
Fixture Information...................................................................................................................................16
Reset Functions.......................................................................................................................................16
Special Functions.....................................................................................................................................17
Offset Mode..................................................................................................................................17
Entering Offset Mode...............................................................................................................................17
Menu Map....................................................................................................................................19
DMX Values.................................................................................................................................20
Mode 1....................................................................................................................................................20
Mode 2....................................................................................................................................................22
5. Technical Information...................................................................................................25
General Maintenance...................................................................................................................25

Table of Contents
-b- Legend 300E Spot User Manual Rev. 01g
Photometrics.................................................................................................................................25
Error Messages ............................................................................................................................26
Troubleshooting Guide..................................................................................................................27
Returns Procedure........................................................................................................................28
Claims..........................................................................................................................................28
Contact Us....................................................................................................................................28
Technical Specifications................................................................................................................29

Before You Begin
Legend 300E Spot User Manual Rev. 01g -1-
1. Before You Begin
What is
Included
•One Legend 300E Spot
•Two omega clamps
•Three additional gobos
•One Warranty Card
•One Quick Reference Guide
Unpacking
Instructions
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above
and that they are all in good condition. If the material inside the container (this product
and any other accessory included with it) appears damaged from shipping, or if the
container shows signs of mishandling, notify the shipper immediately. In addition, retain
the container and all the packing material for inspection.
See the Claims section in the Technical Information chapter.
Typographic
Conventions
Convention Meaning
1~512 A range of values in the text
50/60 A set of mutually exclusive values in the text
[10] A DIP switch to be configured
Claims A new term, or a section or chapter of this document
“COLORado™ UM” The name of another publication or manual
<SET> A button on the fixture’s control panel
Settings A fixture function or a menu option
MENU > Settings
A sequence of menu options
1~10 A range of menu values from which to choose in a menu
Yes/No A set of two mutually exclusive menu options in a menu
ON A unique value to entered or select in a menu
Icon Meaning
Icon Meaning
This icon indicates critical installation, configuration or operation
information. Failure to comply with this information may render
the fixture partially or completely inoperative, damage third-party
equipment, or cause harm to the user.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the fixture from functioning correctly.
This icon indicates useful, although non-critical information.
The term “DMX” used throughout this document refers to the USITT DMX512-A
transmission protocol.

Before You Begin
-2- Legend 300E Spot User Manual Rev. 01g
Safety Notes Please read the following notes
carefully because they include important safety
information about the installation, usage and maintenance of this product.
It is important to read all these notes before starting to work with this product.
There are no user serviceable parts inside this product. Any reference to
servicing it you may find from now on in this User Manual will only apply to
properly CHAUVET® certified technicians. Do not open the housing or attempt
any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for the proper
installation of this product.
Personal Safety
•Avoid direct eye exposure to the light source while the fixture is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Lamp explosion hazard! Do not open the lamp cover within five minutes of having
turned off the fixture.
•The bulb remains hot for a long time after turn off. Never touch the bulb
barehanded and always handle it by its metallic contacts.
•Do not touch this product’s housing when operating because it may be very hot.
Mounting and Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose
this product to rain or moisture.
•Make sure there are no flammable materials close to this product while operating.
•When hanging this product, always secure it to a fastening device using a safety
chain/cable (not provided).
•Do not carry this fixture from the head; use the handles instead.
Power and Wiring
•Always make sure that you are connecting this product to the proper voltage, as
per the specifications in this manual or on the product’s sticker.
•Connect this fixture ONLY to a grounded and protected circuit.
•Never connect this product to a dimmer pack.
•Make sure the fixture’s power cable is not crimped or damaged.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this fixture if you see damage on the housing, lenses, ultraviolet
filter, or cables; have the damaged parts replaced by an authorized technician at
once.
•Do not aim this fixture toward any surface closer than 16 feet (5 m). Otherwise, you
may damage or overheat the illuminated surface.
•Do not cover the ventilation slots when the fixture is operating to avoid internal
overheating.
•Do not aim this fixture toward the Sun. Otherwise, the lenses could concentrate the
solar energy and cause internal overheating.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at a higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Legend 300E Spot may require service, please
contact CHAUVET® Technical Support.

Introduction
Legend 300E Spot User Manual Rev. 01g -3-
2. Introduction
Product
Description
The Legend 300E Spot is a compact, electronic moving yoke spot fixture equipped with
a 300-watt HID lamp. It includes a color wheel with eight slots plus white. It also comes
with two gobo wheels, one with seven rotating slot-n-lock gobos plus open, and the
other with eight fixed gobos plus open. It also includes remote focus and a rotating 3-
facet prism.
Features
•21 or 29-channel compact, fully electronic, 300-watt moving yoke spot
•Pan: 540
⁰
•Tilt: 270⁰
•Color wheel: 7 colors + white
Split/linear colors
Color wheel spins at variable speed
•Gobo wheel 1: Indexed, rotating gobo wheel with gobo shake
7 metal, slot-n-lock gobos + open
Gobo wheel spins at variable speed
16-bit gobo rotation
•Gobo wheel 2: Indexed gobo wheel
8 metal gobos + open
Gobo wheel spins at variable speed
•Static frost
•CTC filters (5,600 K and 3,200 K)
•CMY color mixing system with vector speed adjustments
•3-facet rotating prism
•Variable shutter
•Variable iris
•Variable focus
•Variable 16-bit dimming (0~100%)
•Linear zoom (16~35⁰)
•Individual reset of pan/tilt, color, gobo, shutter, prism, focus
•Move-in-black for pan/tilt, color, gobo
•Remote fixture reset, lamp on/off, and vector control speed adjustments
•Built-in movement macros with range adjustments
•Built-in color macros
•Battery powered display
Additional Features
•3-pin and 5-pin DMX connections
•Three additional free gobos
•User-configurable lamp ignition delay
•User-configurable maintenance reminder
•Electronic ballast with power factor correction
•Electronic power supply
•Automatic pan & tilt correction
•Pan & tilt locks
•Lamp & fixture use timers
•Power saver mode
Options •W-DMX (wireless DMX) receiver
•W-DMX (wireless DMX) transmitter

Introduction
-4- Legend 300E Spot User Manual Rev. 01g
DMX Channel Summary
Mode 1
DMX Channel
Function
Mode 2
DMX Channel
Function
1
Pan
1
Pan
2
Pan Fine
2
Pan Fine
3
Tilt
3
Tilt
4
Tilt Fine
4
Tilt Fine
5
Pan/Tilt Speed
5
Pan/Tilt Speed
6
Dimmer
6
Dimmer
7
Shutter
7
Dimmer Fine
8
Color
8
Shutter
9
Cyan
9
Color
10
Magenta
10
Cyan
11
Yellow
11
Magenta
12
Gobo 1
12
Yellow
13
R-Gobo 1
13
CMY Speed
14
Gobo 2
14
Gobo 1
15
Focus
15
R-Gobo 1
16
Zoom
16
R-Gobo 1 Fine
17
Prism
17
Gobo 2
18
R-Prism
18
Focus
19
Iris
19
Zoom
20
Frost
20
Prism
21
Function
21
R-Prism
22
R-Prism Fine
23
Iris
24
Frost
25
Pan/Tilt Macro
26
P/T Macro Speed
27
Preset Color
28
Color Macro
29
Function

Introduction
Legend 300E Spot User Manual Rev. 01g -5-
Product Overview
Control Panel
Power On/Off
Power Cord
Fuse Holder
DMX In/Out

Setup
-6- Legend 300E Spot User Manual Rev. 01g
3. Setup
AC Power The Legend 300E Spot has an auto-ranging power supply that can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this guide, the product’s user manual, or on the product’s sticker.
Always connect the Legend 300E Spot to a protected circuit with an appropriate
electrical ground to avoid the risk of electrocution or fire.
To determine the power requirements for the Legend 300E Spot
see the label affixed to
the side of the fixture. Alternatively, you may refer to the corresponding
specifications
chart in the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
Please refer to the Sizing the Circuit Breakers section in the Appendix chapter of this
manual.
Never connect the Legend 300E Spot to a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The Legend 300E Spot comes with a bare ended power input cord. The fixture side of
this power cord enters the fixture through a strain reliever (rubber boot) and it cannot be
disconnected from the fixture. Use the table below to wire the plug to the power cord.
Connection Wire (US) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
Make sure to disconnect the fixture’s power cord before replacing a blown fuse,
and always replace it with a fuse of the same type and rating.
Fuse Replacement
1) With a Philips screwdriver, unscrew the fuse holder out of its housing and remove
the blown fuse from its holder.
2) Replace the blown fuse with a fuse of the exact same type and rating.
3) Reverse step 1 and reconnect power.
DMX Linking You may link the Legend 300E Spot to a DMX controller using a standard DMX serial
connection. If using other DMX compatible fixtures with the Legend 300E Spot, it is
possible to control them individually with a single DMX controller.
If you are not familiar with the DMX standard, you may download the “DMX Primer”
document from the CHAUVET® Web site.
DMX Modes
The Legend 300E Spot uses the standard DMX data connection for its DMX Modes
(Mode 1 and Mode 2). You will find information about these DMX modes in the
Introduction chapter (brief description), the Operation Instructions chapter (configuration
details), and the DMX Values section (individual channel values)

Setup
Legend 300E Spot User Manual Rev. 01g -7-
Gobo Wheels
The Legend 300E Spot comes with two gobo wheels. Gobo wheel #1 has seven rotating
gobos, while gobo wheel #2 has eight fixed gobos, as indicated below. The diagram
shows the first and last gobo on each wheel, as per the DMX Values tables.
Rotating Gobos Fixed Gobos
Extra Gobos
Color Wheel
1
7
8
15

Setup
-8- Legend 300E Spot User Manual Rev. 01g
Gobo
Replacement
The gobos in the Legend 300E Spot’s gobo wheel are removable from their gobo plates.
This operation is quite simple, although it requires the technician to be careful and to
follow the recommended procedure.
•Make sure to disconnect the fixture’s power cord before replacing a gobo
•Always replace a gobo with a gobo of the same dimensions.
•When inserting a glass gobo, always make sure that the shinny side of the
gobo (glass base) faces the lamp. This provides a layer of protection against
the high temperature from the lamp.
Procedure 1) Turn the fixture off and disconnect it from the power outlet.
2) Open the head cover by loosening the four fastening screws at the sides of the top
cover.
3) Separate the gobo plate away from the gobo wheel by pushing it toward the front of
the moving head (direction 1 in the diagram). Be careful not to push the gobo out of
the gobo plate.
4) Extract the gobo plate by pulling it outward (direction 2 in the diagram).
5) On a flat surface, remove the expansion ring that holds the gobo in place and
remove the gobo from the gobo plate.
6) Insert a new gobo and hold it in place with the expansion ring.
7) Slide the tip of the gobo plate under the pressure plate near the center of the gobo
wheel.
8) Push the gobo plate inwards. DO NOT force the gobo plate into the gobo wheel slot.
If correctly installed, the gobo plate should accommodate itself in the gobo wheel
slot.
Gobo Replacement
Diagram

Setup
Legend 300E Spot User Manual Rev. 01g -9-
Lamp
Replacement
The Legend 300E Spot is equipped with a Philips MSR Gold 300/2 lamp. This lamp
uses a socket called FastFit, which allows for fast and easy lamp changes. Follow the
procedure below to safely change the Legend 300E Spot’s lamp.
Procedure
1) Turn the fixture off and disconnect it from the power outlet.
2) Wait at least 15 minutes for the lamp to cool down.
3) Loosen the two screws on the lamp cover (marked “A” in the diagram).
4) Lift and rotate the lamp cover as per the diagram to expose the base of the lamp.
5) Rotate the ceramic base of the lamp 90º counterclockwise.
6) Pull the lamp out by holding it from its base only.
7) Insert the new lamp and turn it 90º clockwise.
8) Reverse steps 3 and 4.
9) Use the adjustment screws (marked “B” in the diagram) to position the lamp in the
center of the reflector to obtain the best output.
Lamp Replacement
Diagram
Increasing the
Lamp’s Life
•ALWAYS turn the lamp off by using the DMX controller or the fixture’s control panel.
Then wait at least five minutes before switching off the fixture. This will keep the
fans running to extract any remaining heat from the fixture’s head.
•DO NOT power cycle the fixture unless it is necessary.
•DO NOT touch the lamp without wearing gloves to avoid leaving grease on the bulb
or on the contacts that could reduce the lamp’s life.
•ALWAYS change the lamp when it has reached its recommended lifespan to avoid
the risk of lamp explosion.

Setup
-10- Legend 300E Spot User Manual Rev. 01g
Mounting
Before mounting this fixture, read and follow the safety recommendations indicated in
the Safety Notes (page 2 of this manual).
Orientation
Always mount this fixture in any safe position while making sure that there is adequate
room around it for ventilation.
Make sure to mount this fixture away from any flammable material as indicated in the
Safety Notes (page 2 of this manual).
Rigging
CHAUVET® recommends following the general guidelines below when mounting the
Legend 300E Spot.
•When selecting an installation location, consider ease of access to the fixture for
operation, programming adjustments, and routine maintenance.
•Never mount the fixture in places where rain, high humidity, extreme temperature
changes, or restricted ventilation may affect it.
•If hanging this fixture, make sure that the location where you are mounting the
fixture can support its weight. Please see the Technical Specifications section of this
manual for the weight requirement of this fixture.
Procedure
The Legend 300E Spot comes with an already installed mounting bracket to which you
will be able to attach the two included omega clamps. Be aware that you will have to use
two mounting points per fixture. In addition, you will have to use a safety cable (not
included) to link the fixture to the structure.
Product Mounting
Diagram

Operation
Legend 300E Spot User Manual Rev. 01g -11-
4. Operation
Control Panel
Description
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently selected
value in to the current function
<UP> Navigates upwards through the menu list and increases the numeric
value when in a function
<DOWN> Navigates downwards through the menu list and decreases the
numeric value when in a function
LCD Display
The Legend 300E Spot features a backlit liquid crystal display (LCD) that provides
plenty of information regarding the fixture’s settings and status. In addition, the LCD is
reversible. This allows reading it normally whether the fixture is on the floor or hanging
from a truss.
Upon power up, the LCD will show the Legend logo and the fixture identification, as
shown on the left figure above. After completing the power up tests, the LCD will show
the DMX address, the DMX mode, and the temperature, along with the warning sign if
the tests have detected an error.
Press <ENTER> to read the corresponding error message (see Error Messages in
the Technical Information section).
Press <ENTER> while looking at the error messages to clear them.
Control Options
You can set the Legend 300E Spot start address in the 001~512 DMX range. This
allows for the control of up to 17 fixtures in the 29-channel Mode 2. The Legend 300E
Spot works with any compatible DMX controller using standard DMX cables or the
optional W-DMX receiver.
Programming Carry out all the programming procedures indicated below from the control panel. Refer
to the Menu Map page to learn how the menu options relate to each other
Navigation Buttons
To enter programming mode, press <MENU> until you see the Main Menu.
To highlight a menu option or to change a setting, press <UP> or <DOWN>.
To change menu levels as shown in the Menu Map,press <ENTER> or <MENU>. This
is equivalent to moving right and left of the Menu Map, respectively.
To accept the current or new value, press <ENTER>.
To return to the previous menu without making changes, press <MENU>.
To exit programming mode, press <MENU> until you see the Main Menu or do not press
any button for 30 seconds.

Operation
-12- Legend 300E Spot User Manual Rev. 01g
DMX Functions
From the Main Menu, highlight DMX Functions and press <ENTER> (a new menu with
the DMX functions will open).
DMX Address
1) Highlight DMX Address (the current address will show).
2) Press <MENU> to exit or continue below.
3) To change the current address, press <ENTER> (a pop up window will open).
a) Change the starting address (001~512).
b) Accept the new value.
DMX Mode 1) Highlight DMX Channel Mode (the current mode will show).
2) Press <MENU> to exit or continue below.
3) To change the current mode, press <ENTER> (a pop up window will open).
a) Select a DMX mode (Mode 1/Mode 2).
b) Accept the selected option.
View DMX Values
1) Highlight View DMX Value.
2) Press <MENU> to exit or continue below.
3) Press <ENTER> (the value for each of the attributes of the current DMX mode will
show).
a) Scroll along the list to see the values of all the current attributes.
b) Return to the previous menu.
The list will show either 17 or 25 attributes, depending on the current DMX mode.
W-DMX Settings
1) Highlight WDMX Setting
2) Press <MENU> to exit or continue below.
3) To see the WDMX settings, press <ENTER> (a sub-menu will open).
4) Press <MENU> to exit or continue below.
5) To activate or deactivate W-DMX, highlight Active (the current setting will show)
and press <ENTER> (a pop up window will open).
a) Select YES to activate W-DMX or NO to deactivate W-DMX.
b) Accept the selected option.
6) To enable or disable retransmission, highlight Retransmit (the current setting will
show) and press <ENTER> (a pop up window will open).
a) Select YES to enable retransmission or NO to deactivate retransmission.
b) Accept the selected option.
7) To reset the memory, highlight Reset Memory and press <ENTER> (a pop up
window will open).
a) Select YES to reset the memory or NO to exit without resetting.
b) Accept the selected option.
8) Return to the previous menu.
The W-DMX functionality requires the W-DMX transceiver installed on the Legend
300E Spot fixture.

Operation
Legend 300E Spot User Manual Rev. 01g -13-
Fixture Settings
From the Main Menu, highlight Fixture Settings and press <ENTER> (a new menu with
the fixture settings will open).
Reverse Pan Direction
1) Highlight Pan Inverse (the current setting will show).
2) To reverse the pan direction, press <ENTER> (a pop up window will open).
a) Select YES to reverse the pan direction or NO to use the normal pan direction.
b) Accept the selected option.
Reverse Tilt Direction 1) Highlight Tilt Inverse (the current setting will show).
2) To reverse the tilt direction, press <ENTER> (a pop up window will open).
a) Select YES to reverse the tilt direction or NO to use the normal tilt direction.
b) Accept the selected option.
Head Motion Black Out
1) Highlight Bl.o P/T Moving (the current setting will show).
2) To black out the output when the head moves, press <ENTER> (a pop up window
will open).
a) Select YES to black out the output when the head tilts or pans, or NO to keep
the output on while the head moves.
b) Accept the selected option.
Color Change Black Out 1) Highlight Bl.o Color Change (the current setting will show).
2) To black out the output when the color wheel changes, press <ENTER> (a pop up
window will open).
a) Select YES to black out the output during a color change or NO to keep the
output on to see the color changing.
b) Accept the selected option.
Gobo Change Black Out 1) Highlight Bl.o Gobo Change (the current setting will show).
2) To black out the output when the gobo wheel changes, press <ENTER> (a pop up
window will open).
a) Select YES to black out the output during a gobo change or NO to keep the
output on to see the gobo changing.
b) Accept the selected option.

Operation
-14- Legend 300E Spot User Manual Rev. 01g
Lamp Settings
From the Main Menu, highlight Fixture Settings and press <ENTER>.
The lamp will not ignite if the ambient temperature is 104º F (45º C) or higher.
Lamp On / Off
1) Highlight On/Off (the current setting will show).
2) To turn the lamp on or off, press <ENTER> (a pop up window will open).
a) Select ON to turn the lamp on or OFF to turn the lamp off.
b) Accept the selected option.
Lamp Status During
Power On
1) Highlight State/Power On (the current setting will show).
2) To change the lamp status during power on, press <ENTER> (a pop up window will
open).
a) Select ON to turn on the fixture and the lamp simultaneously or OFF to turn on
the fixture without turning on the lamp.
b) Accept the selected option.
Remote Turn Off 1) Highlight Off Via DMX (the current setting will show).
2) To enable/disable remote turn off, press <ENTER> (a pop up window will open).
a) Select YES to enable fixture turn off from either a DMX controller or its power
switch, or NO to turn the fixture off only from its power switch.
b) Accept the selected option.
Lamp On if DMX Present
1) Highlight On if DMX On (the current setting will show).
2) To turn the lamp on when DMX is present, press <ENTER> (a pop up window will
open).
a) Select YES to turn the lamp on if DMX signal is present, or NO to turn the lamp
on only from the control panel.
b) Accept the selected option.
Lamp Off if DMX Absent 1) Highlight Off if DMX Off (the current setting will show).
2) To turn the lamp off when DMX is absent, press <ENTER> (a pop up window will
open).
a) Select YES to turn the lamp off if DMX signal is absent, or NO to turn the lamp
off only from the control panel.
b) Accept the selected option.
Fan Speed 1) Highlight Cooling Mode (the current setting will show).
2) To change the fan speed setting, press <ENTER> (a pop up window will open).
a) Select AUTO to allow the fixture’s controller to set the fan speed, or HIGH to set
the fan speed to high mode.
b) Accept the new selection.
Lamp Strike Delay
1) Highlight Ignition Delay (the current setting will show).
2) To set the lamp strike delay, press <ENTER> (a pop up window will open).
a) Select the delay before the lamp strikes after power up in seconds (0~255).
b) Accept the new value.
Fixture Shut Off Delay
1) Highlight Low Power Delay (the current setting will show).
2) To set the lamp shut off delay, press <ENTER> (a pop up window will open).
a) Select the delay before the fixture powers off after lamp off in seconds (0~255).
b) Accept the new value.

Operation
Legend 300E Spot User Manual Rev. 01g -15-
Display Settings
From the Main Menu, highlight Display Settings and press <ENTER>
(a new menu
with the DMX functions will open).
Overturn Display
1) Highlight Display Inverse (the current setting will show).
2) To overturn the display, press <ENTER> (a pop up window will open).
a) Select YES to turn the LCD around (fixture hanging from a truss) or NO to keep
the normal LCD view (fixture standing on a surface).
b) Accept the selected option.
LCD Backlight Off
1) Highlight Backlight Auto Off (the current setting will show).
2) To configure the LCD backlight, press <ENTER>.
a) Select YES to automatically turn the LCD backlight off or NO to keep the LCD
backlight always on.
b) Accept the selected option.
Backlight Brightness 1) Highlight Backlight Intensity (the current setting will show).
2) To set the backlight brightness, press <ENTER> (a pop up window will open).
a) Select the backlight brightness (1~10), being “1” the darkest and “10” the
brightest settings.
b) Accept the new value.
Temperature Unit
1) Highlight Temperature Unit (the current setting will show).
2) To select the temperature unit, press <ENTER> (a pop up window will open).
a) Select ºC to show the temperature in the Celsius scale or ºF to show the
temperature in the Fahrenheit scale.
b) Accept the selected option.
Fixture Tests
From the Main Menu, highlight Display Settings and press <ENTER>
(a new menu
with the test functions will open).
Automatic Fixture Test 1) Highlight Auto Test.
2) To start the built-in test sequence, press <ENTER>.
a) The fixture will start the test sequence (pan, tilt, color, CMY, gobo selection,
gobo rotation, shutter, dimmer, prism activation, prism rotation, frost, zoom, and
lamp on/off).
b) You can stop the test by pressing <MENU>.
c) Return to the previous menu.
The automatic fixture test runs only once after activation.
Manual Fixture Test
1) Highlight Manual Test and press <ENTER> (a sub-menu will open).
2) Highlight the desired attribute (the current setting will show).
3) To change the value of the selected attribute, press <ENTER> (a pop up window
will open).
a) Set the attribute value (000~255
) (thefixture will assume the new attribute value
as you change it, as if you were working with a DMX controller).
b) Accept the new value.
4) Repeat steps 2and 3for the other attributes.
5) When done with the test, exit to the previous menu
(the values of all tested channels
will go back to zero).

Operation
-16- Legend 300E Spot User Manual Rev. 01g
Fixture Information
From the Main Menu, highlight Fixture Information and press <ENTER>
(a new menu
with the fixture information will open).
Fixture Operation Timer
1) Highlight Fixture Use Time (the accumulated fixture’s operation time will show).
You cannot modify or reset the fixture operation timer.
Lamp Operation Timer
1) Highlight Lamp On Time (the accumulated lamp’s operation time will show).
2) To reset the lamp operation timer, press <ENTER> (a pop up window will open).
a) Select Reset Time to reset the timer or Exit to exit without resetting.
b) Accept the selected option.
Firmware Version 1) Highlight Firmware Version.
2) To see the firmware versions installed, press <ENTER> (a sub-menu will open)
a) The display will show the current firmware version for each of the four CPU
boards (Athrough D) in the fixture.
b) Return to the previous menu.
Reset Functions From the Main Menu, highlight Reset and press <ENTER> (a new menu with the
resettable attributes will open).
You can leave this sub-menu at any time by pressing <MENU>.
Pan/Tilt Reset
1) Highlight Pan/Tilt and press <ENTER> (a pop up window will open).
a) Select YES to reset the pan and tilt movements to their home positions.
b) Accept the selected option.
Color/CMY Reset 1) Highlight Color/CMY and press <ENTER> (a pop up window will open).
a) Select YES to reset the color wheel and the CMY filters to their home positions.
b) Accept the selected option.
Gobo Reset
1) Highlight Gobo and press <ENTER> (a pop up window will open).
a) Select YES to reset the gobo wheel to its home position.
b) Accept the selected option.
Shutter/Dimmer Reset
1) Highlight Shutter/Dimmer and press <ENTER> (a pop up window will open).
a) Select YES to reset the shutter and dimmer to their home positions.
b) Accept the selected option.
Focus/Zoom/Prism/Frost
Reset
1) Highlight Focus/Zoom/Prism/Frost and press <ENTER> (a pop up window will
open).
a) Select YES to reset the focus, the zoom, the prism, and the frost to their home
positions.
b) Accept the selected option.
Iris/Flatb 1) Highlight Iris//Flatb and press <ENTER> (a pop up window will open).
a) Select YES to reset the iris and flatb to their home positions.
b) Accept the selected option.
Reset All 1) Highlight All and press <ENTER> (a pop up window will open).
a) Select YES to reset all moving optical parts and the moving head to their home
positions.
b) Accept the selected option.