Chauvet Line Dancer LED User manual

5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com
User Manual
Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Auto-ranging
Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle

CHAUVET® Lighting. 2012. All Rights Reserved.
Information and specifications in
this User Manual are subject to change without notice. CHAUVET® assumes no
responsibility or liability for any errors or inaccuracies that may appear in this manual.
TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 2
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
MANUAL CONVENTIONS.........................................................................................................................................................................3
ICONS ..................................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 4
FEATURES............................................................................................................................................................................................4
PRODUCT OVERVIEW ............................................................................................................................................................................5
PRODUCT OVERVIEW (REAR PANEL).......................................................................................................................................................5
3. SETUP............................................................................................................................................................................... 6
ACPOWER...........................................................................................................................................................................................6
Power Linking ............................................................................................................................................................... 6
Orientation .................................................................................................................................................................... 7
Rigging.......................................................................................................................................................................... 7
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 8
CONFIGURING THE STARTING ADDRESS..................................................................................................................................................8
DMXOPERATION .................................................................................................................................................................................8
MASTER/SLAVE ....................................................................................................................................................................................8
STANDALONE OPERATION......................................................................................................................................................................9
Automatic...................................................................................................................................................................... 9
Sound-Active................................................................................................................................................................. 9
Custom Static Color Mixing........................................................................................................................................... 9
DMXCHANNEL VALUES ........................................................................................................................................................................9
5. APPENDIX....................................................................................................................................................................... 10
GENERAL MAINTENANCE .....................................................................................................................................................................10
DATA CABLING....................................................................................................................................................................................10
DATA LINKING.....................................................................................................................................................................................10
GENERAL TROUBLESHOOTING..............................................................................................................................................................11
RETURN PROCEDURE..........................................................................................................................................................................11
CLAIMS ..............................................................................................................................................................................................11
TECHNICAL SPECIFICATIONS ................................................................................................................................................................12
CONTACT US......................................................................................................................................................................................12

Line Dancer LED User Manual 3 Rev. 2
1.BEFORE YOU BEGIN
What is Included
1 x Line Dancer LED™
1 x Power Cable 1 x Warranty Card 1 x User Manual
Unpacking Instructions
Immediately upon receiving a product, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a product
must be returned to the factory, it is important that the product be returned in the original factory box
and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information from
the regular text.
CONVENTION MEANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the product’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating
mode/current status)
MENU > Settings A sequence of menu options to be followed
ON A value to be entered or selected
Icons This manual uses the following icons to indicate information that requires special attention on the part
of the user.
ICONS MEANING
C
ritical installation, configuration or operation information. Failure to
comply with this information may render the product partially or completely
inoperative, cause damage to the product or cause harm to the user.
Important installation or configuration information. Failure to comply with
this information may prevent the product from functioning correctly.
Useful non-critical information.

Line Dancer LED User Manual 4 Rev. 2
Safety Instructions
•Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the product.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not expose product to
rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse source.
•Secure product to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate product at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry the product directly from the cord. Always use the hanging/mounting bracket.
•Avoid direct eye exposure to the light source while it is on.
•
2.INTRODUCTION
Features
•4-channel DMX-512 LED effect light
•Individual control of red, green and blue LEDs
•Variable speed of motor
•Built-in automated programs via master/slave or DMX
•Built-in sound activated programs via master/slave or DMX
Additional Features
•Additional power output: max 30 units
Please read these instructions carefully. It includes important
information about the installation, usage and maintenance of this
product.

Line Dancer LED User Manual 5 Rev. 2
Product Overview
Product Overview (rear panel)
Single-yoke
Hanging/Standing
Brackets (2)
Bracket Adjustment
Knobs(2)
Signal Indicator
LED
Sound Sensitivity
Adjustment Knob
Microphone
Power Link Out
Power
In/Fuseholder
DMX In
DMX Out
Safety Attachment
Point
DIP Switches
Power Indicator
LED

Line Dancer LED User Manual 6 Rev. 2
3.SETUP
AC Power This product runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line
voltage to which you are connecting it is within the range of accepted voltages.
Always connect the product to a switched circuit. Never connect the product to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0
to 100% switch.
To determine the power requirements for a particular product, see the label affixed to the back plate
of the product or refer to the product’s specifications chart. A product’s listed current rating indicates
its average current draw under normal conditions.
Always connect the product to a circuit with a suitable electrical ground.
Power Linking
This product contains power linking via the edison outlet located in front of the power input cable.
Please see the diagram below for further explanation.
The maximum quantity of products that may be linked is 30.
Additional power
link out
Fixture #1
Fixture #2
Fixture #3

Line Dancer LED User Manual 7 Rev. 2
Do not use a tool on
the bracket
adjustment knob
Hanging
Bracket
Mounting
Orientation
The Line Dancer LED™ may be mounted in any safe position, provided there is adequate room for
ventilation.
Rigging
Be sure that the structure can support the weight of the product. Please see the “Technical
Specifications” section of this manual for a detailed weight listing. Mount the product securely. This
may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm in
size. When rigging consider routine maintenance and control panel access. Please see the following
steps for installation.
•If the power link out is intended to be used with multiple product, take into account the
length of each power cable, and mount the products close enough to one another to
accommodate for this.
•When aiming the products, you may use the bracket adjustment knob. Loosen the knob,
adjust to the desired angle, and then tighten the knob by turning clockwise. Do not use
tools for this step, as it may cause damage.
•Safety cables must always be used.

Line Dancer LED User Manual 8 Rev. 2
4. OPERATING INSTRUCTIONS
Configuring the Starting Address
Each product requires a starting address from 1~512. A product requiring one or more channels for control
begins to read the data on the channel indicated by the starting address. For example, a product that uses
seven DMX channels and is addressed to start on DMX channel 100, will read data from channels: 100, 101,
102, 103, 104, 105 and 106. Choose the starting addresses for each product so that the channels used do not
overlap. In addition, you should note the starting address selected for future reference. The Line Dancer LED™
product uses four DMX channels. If this is your first time using DMX, download the DMX Primer from
www.chauvetlighting.com.
DMX Operation
This is the operating mode which will allow for control with an external DMX controller. You must set the starting
address for this mode. If you are unfamiliar with DMX, download the DMX Primer from
www.chauvetlighting.com.
1. Plug the DMX controller into the product.
2. Using the DIP switches 1~9, assign the DMX starting address.
The blue LED located directly to the right of the DIP switches will blink rapidly when the
product detects DMX signal.
This product will switch to DMX mode automatically when a DMX controller is plugged into the
product.
Master/Slave
This is the operating mode which will allow 1 product to act as the “master” and control all of the other “slave”
products. You must set both the master and the slave(s) products to the correct mode for this operation.
Master Settings:
1. You may choose to operate this product in Automatic or Sound mode on the master product. Please
see the standalone options for these settings.
Slave Settings:
1. Set all DIP switches to the OFF position.
The first product in the chain will automatically be set to the master. When all of the DIP switches on
the slave products are set to the OFF position, they will follow the master.
Do not connect a DMX controller to the daisy chain for this operating mode.

Line Dancer LED User Manual 9 Rev. 2
Standalone Operation
Automatic
This product has preprogrammed chases. These are accessed via the DIP switches on the back of the
product. Please see the instructions below for further explanation.
1. Set DIP switch [10] to the ON position.
2. Set DIP switch [9] to the OFF position.
Sound-Active
This product has preprogrammed sound triggered chases. These are accessed via the DIP switches, and
the speed may be adjusted using the audio adjustment knob. Please see the instructions below for further
explanation.
1. Set DIP switch [9] to the ON position.
2. Set DIP switch [10] to the OFF position.
Custom Static Color Mixing
This product has the ability to accept custom settings. These are accessed via the DIP switches. Please
see the list below for these DIP switch settings.
Function DIP switch
Red 1
Green 2
Blue 3
Strobe Speed 4~8
The rotation speed is fixed to the default setting in this mode. It is not possible to adjust this speed in
standalone operation.
DMX Channel Values
CHANNEL
VALUE
FUNCTION
1
000 255
021 040
041 060
061 080
081 100
101 120
121 140
141 160
161 180
181 200
201 220
221 240
241

255
Mode
No Function
Red
Green
Blue
Red/Green
Red/Blue
Green/Blue
Red/Green/Blue
Mode 1
Mode 2
Mode 3
Mode 4
Sound
2 000 009
010 255
Strobe (only when CH.1 is between 021~240)
No Function
Slow ~ Fast
3 000 009
010 255
Run Speed (only when CH.1 is between 161~240)
No Function
Slow ~ Fast
4 000 009
010 255
Motor Speed
No Function
Slow ~ Fast

Line Dancer LED User Manual 10 Rev. 2
5.APPENDIX
General Maintenance
To maintain optimum performance and minimize wear, products should be cleaned frequently.
Usage and environment are contributing factors in determining frequency. As a general rule, products
should be cleaned at least twice a month. Dust build up reduces light output performance and can
cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to
power off product before conducting maintenance.
•Unplug product from power.
•Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
•Clean all glass when the product is cold with a mild solution of glass cleaner or Isopropyl
Alcohol and a soft lint free cotton cloth or lens tissue.
•Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
•Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the product operates. Damp, smoky
or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean
with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.
Clean the product at least every 30/60 days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
Data Cabling
To link products together you must obtain data cables. You can purchase CHAUVET® certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference. Use a Belden© 9841 or equivalent cable which meets the specifications
for EIA RS-485 applications.
Data Linking
You will need a serial data link to run light shows of one or more products using a DMX controller or
to run synchronized shows on two or more products set to a master/slave operating mode. The
combined number of channels required by all the products on a serial data link determines the
number of products the data link can support.
Products on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard, no more than 32 products should be connected on one data link.
Connecting more than 32 products on one serial data link without the use of a DMX optically-
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of products on a serial data link: 32

Line Dancer LED User Manual 11 Rev. 2
General Troubleshooting
SYMPTOM POSSIBLE CAUSE(S) POSSIBLE ACTION(S)
Breaker/Fuse
keeps blowing
Excessive circuit load Check total load placed on the electrical circuit.
Short circuit along the power wires Check for a short in the electrical wiring (internal and/or
external)
Device does not
power up No power Check for power on power outlet
Loose power cord Check power cord
Product is not
responding to
DMX
Wrong DMX addressing Check Control Panel and unit addressing
Damaged DMX cables Check DMX cables
Wrong polarity settings on the
controller Check polarity switch settings on the controller
Loose DMX cables Check cable connections
Faulty DMX interface Replace DMX input
Faulty Main PCB Replace Main PCB
Loss of signal
Non DMX cables Use only DMX compatible cables
Bouncing signals Install terminator as suggested
Long cable / Low level signal Install amplifier right after product with strong signal
Too many products Install an optically coupled DMX splitter after unit #32
Interference from AC wires Keep DMX cables separated from power cables or black
lights
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support.
Return Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused. Call CHAUVET® and request an RMA # prior to
shipping the product. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to pack product properly; any shipping damage resulting from
inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS packing or
double-boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper inside
the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a product is damaged due to shipping. Any other
claim for items such as missing component/part, damage not related to shipping, and concealed
damage, must be made within seven (7) days of receiving merchandise.

Line Dancer LED User Manual 12 Rev. 2
Technical Specifications
WEIGHT & DIMENSIONS
Length....................................................................................................................................................... 12.9 in (327 mm)
Width......................................................................................................................................................... 12.4 in (316 mm)
Height........................................................................................................................................................ 11.5 in (291 mm)
Weight...........................................................................................................................................................9.2 lbs (4.2 kg)
POWER
Auto-ranging Power Supply...........................................................................................................100~240 VAC, 50/60 Hz
Power Consumption @ 120 VAC, 60 Hz.............................................................................. 8 W (0.2 A) max, 0.2 A inrush
Power Consumption @ 230 VAC, 50 Hz............................................................................ 10 W (0.1 A) max, 0.2 A inrush
Power output.................................................................................................................................................... 30 units max
Fuse..................................................................................................................................................................F 2 A, 250 V
LIGHT SOURCE
LED...................................................................................................................72 (24 red, 24 green, 24 blue) 100,000 hrs
PHOTO OPTIC
Coverage Angle.............................................................................................................................................................. 70°
THERMAL
Maximum ambient temperature.....................................................................................................................104° F (40° C)
ORDERING INFORMATION
Line Dancer LED™..............................................................................................................................LINCEDANCERLED
WARRANTY INFORMATION
Warranty .......................................................................................................................................... 2-year limited warranty
Contact Us
World Wide General Information CHAUVET® Lighting
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET® Lighting
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com