Chauvet 4 Bar Flex User manual

4BAR™ User Manual 1 2/8/2012 10:53 AM
4BAR™
User Manual
Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Auto-ranging
Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle
(Included)

4BAR™ User Manual 2 2/8/2012 10:53 AM
CHAUVET® 2010. All Rights Reserved.
Information and specifications in this User Manual are subject to change without notice. CHAUVET® assumes no
responsibility or liability for any errors or inaccuracies t
hat may appear in this manual.
TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 2
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
MANUAL CONVENTIONS.........................................................................................................................................................................3
ICONS ..................................................................................................................................................................................................3
ACPOWER...........................................................................................................................................................................................4
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 5
FEATURES (FIXTURE).............................................................................................................................................................................5
FEATURES (FOOTSWITCH)......................................................................................................................................................................5
Additional Features....................................................................................................................................................... 5
DMXCHANNEL VALUES........................................................................................................................................................................5
PRODUCT OVERVIEW ............................................................................................................................................................................6
3. SETUP............................................................................................................................................................................... 6
FUSE REPLACEMENT.............................................................................................................................................................................7
MOUNTING ...........................................................................................................................................................................................7
Orientation .................................................................................................................................................................... 7
Rigging.......................................................................................................................................................................... 7
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 7
NAVIGATING THE CONTROL PANEL .........................................................................................................................................................8
MENU MAP...........................................................................................................................................................................................8
OPERATION..........................................................................................................................................................................................8
DMX Mode.................................................................................................................................................................... 8
Automatic Mode............................................................................................................................................................ 9
Sound Mode.................................................................................................................................................................. 9
MASTER/SLAVE OPERATION.................................................................................................................................................................10
FOOTSWITCH OPERATION....................................................................................................................................................................10
There is no need to modify any settings for the 4BAR™ before connecting the footswitch. It will operate properly in
any mode.................................................................................................................................................................... 11
Disconnecting the Footswitch..................................................................................................................................... 11
GENERAL TROUBLESHOOTING..............................................................................................................................................................12
CONTACT US......................................................................................................................................................................................13
GENERAL MAINTENANCE .....................................................................................................................................................................14
RETURNS PROCEDURE........................................................................................................................................................................14
CLAIMS ..............................................................................................................................................................................................14
TECHNICAL SPECIFICATIONS ................................................................................................................................................................15

4BAR™ User Manual 3 2/8/2012 10:53 AM
1. BEFORE YOU BEGIN
What is included
Ø1 x 4BAR™
Ø1 x 4BAR™ transport bag
Ø1 x Tripod stand
Ø1 x Tripod stand transport bag
Ø1 x Footswitch
Ø1 x Warranty Card
Ø1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information from
the regular text.
CONVENTION MEANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the fixture’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating mode/current status)
MENU > Settings A sequence of menu options to be followed
ON A value to be entered or selected
Icons
This manual uses the following icons to indicate information that requires special attention on the part
of the user.
ICONS MEANING
This paragraph contains critical installation, configuration or operation information. Failure
to comply with this information may render the fixture partially or completely inoperative,
cause damage to the fixture or cause harm to the user.
This paragraph contains important installation or configuration information. Failure to
comply with this information may prevent the fixture from functioning correctly.
This paragraph reminds you of useful, although not critical, information.

4BAR™ User Manual 4 2/8/2012 10:53 AM
AC Power
This fixture has an auto-ranging power supply that can accommodate a wide range of input voltages.
The only thing necessary to do before powering on the unit is to make sure the line voltage you are
applying is within the range of accepted voltages. This fixture will accommodate between 100~240
VAC, 50-60 Hz. All fixtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for
a 0% to 100% switch.
All fixtures must be connected to circuits with a suitable Earth Ground.
Safety Instructions
•Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to
rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse and be sure to
replace with same lamp source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Avoid direct eye exposure to the light source while it is on.
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact
CHAUVET® at: 954-929-1115.
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.

4BAR™ User Manual 5 2/8/2012 10:53 AM
2. INTRODUCTION
Features (fixture)
•15-channel DMX LED wash light system
•RGB control of 4 separate lights
•Built-in automated programs via DMX
•Built-in sound activated programs DMX
Features (footswitch)
•Trigger built-in static or automated programs (includes RGB fades)
•Instantly set any program to sound active
•Instantly blackout any program
Additional Features
•Includes footswitch with 33 ft cable, tripod with bag and transport case for lights
•Independent positioning of each light
•Low-profile lights are 1.7 in deep
•Adjustable stand height from 56 in to 91 in
DMX Channel Values
CHANNEL
VALUE
FUNCTION
Description
CH 1 Auto Programs
1
000 ó009
010 ó249
250 ó255
Control/Operating Mode
RGB Mode (ch.2-15)
Auto Programs
Sound-Active
010 ó029
030 ó049
050 ó069
070 ó089
090 ó109
110 ó129
130 ó149
150 ó169
170 ó189
190 ó209
210 ó229
230 ó249
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Auto 11
Auto 12
2
000 ó009
010 ó255
Master dimmer
No function
Dimmer (low óhigh)
3
000 ó009
010 ó255
Strobe
No function
Strobe (slow ófast)
4
000 ó255
Red 1
RGB Color Mixing
0% ó100%
5
000 ó255
Green 1
6
000 ó255
Blue 1
7
000 ó255
Red 2
RGB Color Mixing
0% ó100%
8
000 ó255
Green 2
9
000 ó255
Blue 2
10
000 ó255
Red 3
RGB Color Mixing
0% ó100%
11
000 ó255
Green 3
12
000 ó255
Blue 3
13
000 ó255
Red 4
RGB Color Mixing
0% ó100%
14
000 ó255
Green 4
15
000 ó255
Blue 4

4BAR™ User Manual 6 2/8/2012 10:53 AM
Product Overview
Power In
4-pin Footswitch
Connection
Control Panel
Microphone
Sound Sensitivity
Adjustment Knob
DMX In
DMX Out
4
3
1
2
Fuseholder

4BAR™ User Manual 7 2/8/2012 10:53 AM
The fuse is located
inside this
compartment.
Remove using a flat
head screwdriver.
3. SETUP
Fuse Replacement
With a flat head screwdriver wedge the fuse
holder out of its housing. Remove the damaged
fuse from its holder and replace with exact
same type fuse. Insert the fuse holder back in
its place and reconnect power.
Mounting
Orientation
This fixture may be mounted on the included tripod stand, in any location, provided there is adequate
room for ventilation.
Rigging
There are two methods of mounting this fixture.
•Using the included tripod stand
•Using a clamp on the two clamp hanging bolts
Adjust the angle of the each of the four lights on the fixture by loosening both knobs and tilting the
fixture. After finding the desired position, retighten both knobs.
oWhen selecting installation location, take into consideration access and routine
maintenance.
oNever mount in places where the fixture will be exposed to rain, high humidity,
extreme temperature changes or restricted ventilation.
oThe clamps for hanging are sold separately.
oWhen using the clamp hanging bolts, BOTH of the two hanging positions MUST be
used.
Disconnect the power cord before replacing a fuse and always
replace with the same type fuse.
Clamp hanging bolts
(2) two total
Light pan angle
adjustment knob
Light tilt angle
adjustment knob

4BAR™ User Manual 8 2/8/2012 10:53 AM
4.OPERATING INSTRUCTIONS
Navigating the Control Panel
Access control panel functions using the three panel buttons located directly underneath the LED
Display.
The Control Panel LED Display shows the menu items you select from the menu map .When a menu
function is selected, the display will show immediately the first available option for the selected menu
function.
Menu Map
MENU OPTION
SUB-MENU
FUNCTION /DESCRIPTION
UP BUTTON
DOWN BUTTON
*512
Auto displays
d.***
after 3 seconds
A***
Allows to change DMX address
Changes DMX address
in ascending order
Changes DMX address
in descending order
d.***
Displays DMX address; cannot change
*SND
Sets to sound-active Displays current speed Displays current speed
AUTO
Plays program automatically Displays current speed Displays current speed
S*** Allows to change Auto speed Change run speed in
ascending order Change run speed in descending order
Operation
DMX Mode
This mode allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with
DMX, download the DMX Primer from the www.chauvetlighting.com website.
1) Press the <MENU> button until one of the following is displayed: AUTO, SND, 512.
2) Immediately, press the <UP> button until 512is displayed (not necessary if 512is already
displayed).
3) Wait for 5 seconds, until the display reads “d.***”.
4) Press <MENU>until the display reads “A***”.
5) Then, use the <UP> and <DOWN> buttons to select the DMX starting address.
Button
Function
<MENU>
Used to access the menu or to return to a
previous menu option
<DOWN>
Scrolls through menu options in descending
order
<UP>
Scrolls through menu options in ascending
order

4BAR™ User Manual 9 2/8/2012 10:53 AM
Automatic Mode
This fixture has several built-in automatic programs. To access them, please see the below
instructions:
1) Press the <MENU> button until one of the following is displayed: AUTO, SND,
512.
2) Immediately, press the <DOWN> button until AUTO is displayed (not necessary if
AUTO is already displayed).
3) Wait for 5 seconds.
4) Press <MENU> until the display reads “S***”.
5) Then, use the <UP> and <DOWN> buttons to select the operating speed of the program.
Sound Mode
This fixture has several built-in automatic programs. To trigger these programs via sound, please see
the below instructions:
1) Press the <MENU> button until one of the following is displayed: AUTO, SND,
512.
2) Immediately, press the <UP> button until SND is displayed (not necessary if SND is
already displayed).
3) Wait for 5 seconds.
1. Then, use the <SOUND SENSITIVITY ADJUSTMENT KNOB> to adjustment the sensitivity
of the program to the sound received from the microphone.

4BAR™ User Manual 10 2/8/2012 10:53 AM
Master/Slave Operation
This mode allows for multiple 4BAR™s to be controlled with a single footswitch. Please see the
following instructions for the setup.
1) Connect the footswitch to the first 4BAR™.
2) Then, connect from the DMX Out of the Master 4BAR™ to the DMX In of the Slave unit.
3) Set the DMX starting address of the Slave(s) to “001”.
Master
Slave
DMX out to other
slave fixture(s)

4BAR™ User Manual 11 2/8/2012 10:53 AM
Footswitch operation
The included footswitch provides quick access to preset colors, color change programs, and triggering via the
onboard microphone on the 4BAR™. Please see the chart, along with the set of instructions, below for further
explanation.
1. Power on the fixture.
2. Connect the footswitch to the 4BAR™ via the 4-pin connection cable with plug.
3. Press pedal # 1 (Preset) to activate control. When this is operating properly, the LEDs on the 4BAR™ will
light white (first function on pedal # 1)
PEDAL
SUB-OPTION
FUNCTION
1
(PRESET)
1 x press
White
2 x press
Red
3 x press
Green
4 x press
Blue
5 x press
Cyan
6 x press
Yellow
7 x press
Violet
8 x press
Color change every second in a continuous loop
9 x press
Color change every 3 seconds in a continuous loop
2
(SOUND ON)
- Sound controlled
3
(BLACKOUT)
- Blackout
There is no need to modify any settings for the 4BAR™ before connecting the footswitch. It will operate
properly in any mode.
There is no need to modify any settings for the 4BAR™ before connecting the footswitch. It will operate
properly in any mode.
Disconnecting the Footswitch
In order to properly disconnect the footswitch, please follow these steps:
1. Unplug the footswitch from the 4BAR™.
2. Turn the power to the fixture off (unplug the power cable).
3. Turn the power to the fixture on again (plug in the power cable), and the fixture will properly operate on any one of
the 3 modes.

4BAR™ User Manual 12 2/8/2012 10:53 AM
General Troubleshooting
Symptom Solution(s)
Applies to
Lights
Foggers
& Snow Controllers
Dimmers
& Chaser
Auto shut off
Check fan thermal switch reset
ü
Breaker/Fuse keeps
blowing
Check total load placed on device
ü
Device has no power
Check for power on Mains.
Check device’s fuse. (internal and/or external)
ü üü
Fixture is on but there
is no movement to the
audio
Make sure you have the correct audio mode on the
control switches. If audio provided via ¼” jack,
make sure a live audio signal exists
Adjust sound sensitivity knob
ü üü
Lamps cuts off
sporadically
Possible bad lamp or fixture is overheating.
Lamp may be at end of its life.
ü
Light will not come on
after power failure
Some discharge lamps require a cooling off period
before the electronics in the fixture can kick start it
again, wait 5 to 10 minutes before powering up
ü
Loss of signal
Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power
cables or black lights.
üüüü
No flash
Re-install bulb, may have shifted in shipping
ü
No light output
Check slip ring & brushes for contact
Install bulb
Call service technician
ü
Remote does not work
Make sure connector is firmly connected to device
ü
ü
Stand alone mode
All Chauvet lighting fixtures featuring stand-alone
functions do not require additional settings, simply
power the fixture and it will automatically enter into
this mode
ü
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support at the location on the next page.

4BAR™ User Manual 13 2/8/2012 10:53 AM
Contact Us
World Wide
General Information CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com

4BAR™ User Manual 14 2/8/2012 10:53 AM
General Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).
Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from
inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is
always a safe method to use.
Note: If you are given an RMA #, please include the following information on a piece of
paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

4BAR™ User Manual 15 2/8/2012 10:53 AM
Technical Specifications
WEIGHT & DIMENSIONS
Length........................................................................................................................... 47 in (1,193 mm)
Height (fully extended) ................................................................................................. 91 in (2,311 mm)
Weight .............................................................................................................................29 lbs (13.2 kg)
POWER
Auto-ranging power supply................................................................................100~240 VAC, 50/60 Hz
Power consumption @ 120 V, 60 Hz ............................................................................48 W, 0.4 A max
Inrush current @ 120 V, 60 Hz........................................................................................................ 0.8 A
Power consumption @ 230 V, 50 Hz ............................................................................37 W, 0.2 A max
Inrush current @ 230 V, 50 Hz........................................................................................................ 0.2 A
Fuse......................................................................................................................................F 2 A, 250 V
LIGHT SOURCE
LED.........................................432 10 mm (108 per light) (144 Red, 144 Green, 144 Blue) 100,000 hrs
PHOTO OPTIC
Luminance @ 1 m (per light, 1 of 4).............................................................................................980 lux
Beam Angle (per light, 1 of 4)............................................................................................................. 21°
Field Angle (per light, 1 of 4) .............................................................................................................. 33°
THERMAL
Maximum ambient operating temperature.........................................................................104° F (40° C)
CONTROL & PROGRAMMING
Data input................................................................................................locking 3-pin XLR male socket
Data output...........................................................................................locking 3-pin XLR female socket
Data pin configuration ..............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols......................................................................................................................USITT DMX512-A
DMX Channels .....................................................................................................................................15
ORDERING INFORMATION
4BAR™........................................................................................................................................... 4BAR
WARRANTY INFORMATION
Warranty.............................................................................................................. 2-year limited warranty