Chauvet SlimBEAM QUAD IRC User manual

User Manual

Page 2 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Product at a Glance ........................................................................................................................4
Safety Notes....................................................................................................................................4
2. Introduction................................................................................................................... 5
Product Overview............................................................................................................................5
Product Dimensions........................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power........................................................................................................................................7
Fuse Replacement..........................................................................................................................7
Power Linking......................................................................................................................................... 7
Mounting .........................................................................................................................................8
Orientation.............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation....................................................................................................................... 9
Control Panel Operation..................................................................................................................9
Menu Map .......................................................................................................................................9
DMX Linking....................................................................................................................................9
Configuration (DMX) .......................................................................................................................9
DMX Personality and Starting Address................................................................................................... 9
DMX Channel Assignments and Values.......................................................................................10
16CH .................................................................................................................................................... 10
SlimBEAM™ QUAD IRC Zones for DMX Control................................................................................. 10
9-CH..................................................................................................................................................... 11
9-CH (cont.).......................................................................................................................................... 12
4-CH..................................................................................................................................................... 12
Configuration (Standalone)...........................................................................................................13
Static Color Mode................................................................................................................................. 13
Auto Program Mode.............................................................................................................................. 13
Program Speed..................................................................................................................................... 13
Sound-Active Mode .............................................................................................................................. 13
Sound Sensitivity.................................................................................................................................. 13
Custom Color Mixing Mode .................................................................................................................. 13
Dimmer Mode....................................................................................................................................... 14
IRC-6 Infrared Remote Control............................................................................................................. 14
IRC-6 Operation.................................................................................................................................... 14
Master/Slave Mode............................................................................................................................... 15
5. Maintenance .................................................................................................................16
Product Maintenance....................................................................................................................16
6. Technical Specifications..............................................................................................17
Returns .............................................................................................................................18
Contact Us........................................................................................................................19

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 3 of 19
1.BEFORE YOU BEGIN
What Is
Included
•SlimBEAM™ QUAD IRC
•Power Cord •Warranty Card •Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container
to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure
to report damage to the carrier immediately may invalidate your claim. In addition, keep the
box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. Chauvet
assumes no responsibility or liability for any errors or omissions
that may appear in this manual. Chauvet
reserves the right to update the existing
document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Updated
R. Isenstadt 03/24/15 A. Leon 04/14/15

Page 4 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, make sure there is adequate support for the
product’s weight, and always secure to a fastening device using a safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer or rheostat.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always carry by
the base.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 5 of 19
2.INTRODUCTION
Product Overview
DMX In
Power In
Microphone
Power Out
Safety
Loop
Fuse
Holder
Display
Menu
Buttons
Adjustment
Knobs
IR Sensor
DMX Out

Page 6 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
Product Dimensions
10.8 in
273 mm
8.3 in
212 mm
3.2 in
80 mm

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 7 of 19
3.SETUP
AC Power
The SlimBEAM™ QUAD IRC has an auto-
ranging power supply and it can work with an
input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s
power
requirements (
circuit breaker, power outlet, and wiring), use the current value listed on the
label affixed to the product’s back panel, or refer to the product
’s specifications chart. The
listed current rating indicates the product’s average current draw under normal conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or
fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
4. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking The product provides power linking via the Edison
outlet located in the back of the unit.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 18 SlimBEAM™ QUAD IRC unit
s on 120 VAC or up to
34 SlimBEAM™ QUAD IRC units on 230 VAC.
The power linking diagram corresponds to the North American version of the product
ONLY! If using the product in other markets, you must consult with the local Chauvet
distributor as power linking connectors and requirements may differ in your country or
region.
1st Product
2nd Product
3rd Product
Additional
Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in the
Safety Notes.
Orientation
The SlimBEAM™ QUAD IRC
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy access
to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product can support the
product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp
of appropriate weight
capacity.
•When power linking multiple products, mount the products close enough for
power
linking cables to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
M12 Threaded
Holes
Rubber Feet x4
(for floor mounting)
Mounting Clamps
(such as the CLP-15N
from Chauvet)
Safety Cable
(such as CH-05 from Chauvet)

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 9 of 19
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Please refer to the Product Overview to see the button locations on the control panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
DMX Mode
4-CH
d 1–d512 Selects the DMX Personality and the DMX
starting address
9-CH
16CH
Static Color Mode
C--
C1–C 15
Selects 1 of 15 static colors
Auto Program Mode
P--
P1–P 10
Selects 1 of 10 auto program
Program Speed
S--
S 1–S100
Sets auto program speed (slow to fast)
Sound-Active Mode
Snd
Selects Sound-Active mode
Sound Sensitivity
SenS
u 0–u100
Sets the sound sensitivity
Custom Color Mixing
Mode U--
r 0–r255
Red (0–100%)
g 0–g255
Green (0–100%)
b 0–b255
Blue (0–100%)
A0–A255
Amber (0–100%)
Dimmer dIN
OFF
No dimming curve
dIN1
Fast dimming curve
dIN2 Medium dimming curve
dIN3
Slow dimming curve
Infrared Mode SET
ON
Turns infrared on or off
OFF
DMX Linking
The SlimBEAM™ QUAD IRC
works with a DMX controller. Information about DMX is in the
CHAUVET® DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
DMX Personality
and Starting
Address
When selecting a starting DMX address, alway
s consider the number of DMX channels the
selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The SlimBEAM™ QUAD IRC uses up to 16 DMX channels, which defines the highest
configurable address to 497.
If you are not familiar with the DMX protocol, download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly until 4-CH, 9-CH, or 16CH shows on the display.
2. Press <ENTER> when the desired personality is selected, and d 1–d512 will show on
the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.

Page 10 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
DMX Channel Assignments and Values
16CH
Channel
Function
Value
Percent/Setting
1
Red 1
000ó255
0–100%
2
Green 1
000ó255 0–100%
3
Blue 1
000
ó
255
0–100%
4
Amber 1
000
ó
255
0–100%
5
Red 2
000ó255
0–100%
6
Green 2
000ó255 0–100%
7
Blue 2
000
ó
255
0–100%
8
Amber 2
000ó255
0–100%
9
Red 3
000ó255
0–100%
10
Green 3
000ó255 0–100%
11
Blue 3
000
ó
255
0–100%
12
Amber 3
000ó255
0–100%
13
Strobe
000
ó
010
No function
011ó255
Strobe, slow to fast
Program Speed 000ó255
Program speed, slow to fast,
when CH. 14 is 011–230
Sound Sensitivity
000ó010
Off
011ó255 Sound sensitivity, low to high,
when CH. 14 is 231–255
14 Auto/Sound
Programs
000
ó
010
No function
011ó032
Auto program 1
033ó054
Auto program 2
055ó076
Auto program 3
077
ó
098
Auto program 4
099ó120
Auto program 5
121ó142
Auto program 6
143ó164
Auto program 7
165ó186
Auto program 8
187
ó
208
Auto program 9
209ó230
Auto program 10 (Cycles through all programs)
231ó255
Sound program
15
Dimmer
000ó255 0–100%
16 Dimmer Speed Mode
000
ó
051
Preset dimmer speed from display menu
052ó101
Dimmer speed mode off
102ó152
Dimmer speed mode1 (fast speed)
153ó203
Dimmer speed mode2 (middle speed)
204
ó
255
Dimmer speed mode3 (slow speed)
SlimBEAM™
QUAD IRC
Zones for
DMX Control
1
2
3

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 11 of 19
9-
CH
Channel
Function
Value
Percent/Setting
1
Red
000ó255
0–100%
2
Green
000
ó
255
0–100%
3
Blue
000ó255 0–100%
4
Amber
000
ó
255
0–100%
5 Color Macros and
Color Temperature
000
ó
010
No function
011ó030
R: 100%
G: 0–100%
B: 0
A: 0
031ó050
R: 100%–0
G: 100%
B: 0
A: 0
051ó070
R: 0
G: 100%
B: 0–100%
A: 0
071ó090
R: 0
G: 100%–0
B: 100%
A: 0
091ó110
R: 0–100%
G: 0
B: 100%
A: 0
111ó130
R: 100%
G: 0
B: 100%–0
A: 0
131ó150
R: 100%
G: 0–100%
B: 0–100%
A: 0
151ó170
R: 100%–0
G: 100%–0
B: 100%
A: 0
171ó200
R: 100%
G: 100%
B: 100%
A: 100%
201ó205
Color temperature 1
206ó210
Color temperature 2
211
ó
215
Color temperature 3
216
ó
220
Color temperature 4
221
ó
225
Color temperature 5
226
ó
230
Color temperature 6
231ó235 Color temperature 7
236
ó
240
Color temperature 8
241
ó
245
Color temperature 9
246
ó
250
Color temperature 10
251
ó
255
Color temperature 11
6
Strobe
000
ó
010
No function
011
ó
255
Strobe, slow to fast
Program Speed 000ó255 Program speed, slow to fast,
when CH. 7 is
011
–
230
Sound Sensitivity
000
ó
010
Off
011ó255
Sound sensitivity, low to high,
when CH. 7 is 231–255

Page 12 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
9-
CH
(cont.)
Channel
Function
Value
Percent/Setting
7Auto/Sound
Programs
000
ó
010
No function
011
ó
032
Auto program 1
033ó054 Auto program 2
055
ó
076
Auto program 3
077
ó
098
Auto program 4
099
ó
120
Auto program 5
121
ó
142
Auto program 6
143ó164 Auto program 7
165
ó
186
Auto program 8
187
ó
208
Auto program 9
209
ó
230
Auto program 10 (Cycles through all programs)
231
ó
255
Sound program
8
Dimmer
000ó255 0–100%
9 Dimmer Speed Mode
000
ó
051
Preset dimmer speed from display menu
052
ó
101
Dimmer speed mode off
102ó152 Dimmer speed mode1 (fast speed)
153
ó
203
Dimmer speed mode2 (middle speed)
204
ó
255
Dimmer speed mode3 (slow speed)
4-CH
Channel
Function
Value
Percent/Setting
1
Red
000ó255
0–100%
2
Green
000
ó
255
0–100%
3
Blue
000ó255
0–100%
4
Amber
000ó255 0–100%

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 13 of 19
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
•Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX signals
that could interfere with the DMX signals from the controller.
Static Color Mode
To run the SlimBEAM™ QUAD IRC in static-color mode, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER> and C 1–C15 will show on the display.
3. Use <UP> or <DOWN> to select the desired color.
4. Press <ENTER>.
Auto Program
Mode
To run the SlimBEAM™ QUAD IRC in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER> and P 1–P 10 will show on the display.
3. Use <UP> or <DOWN> to select the desired program.
4. Press <ENTER>.
Program Speed
To adjust the auto program speed, follow the instructions below:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Press <UP> or <DOWN> and S 1–S100 will show on the display.
3. Use <UP> or <DOWN> to increase or decrease the program speed.
4. Press <ENTER> at the desired speed to set it and return to Auto Program mode.
Sound-Active
Mode
To run the SlimBEAM™ QUAD IRC in sound-active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Sound Sensitivity
To adjust the sound sensitivity, follow the instructions below:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Press <UP> or <DOWN> and u 0–u100 will show on the display.
3. Use <UP> or <DOWN> to increase or decrease the sound sensitivity.
4. Press <ENTER> when the product responds to the beat of the music to set the
sensitivity and return to Sound-Active mode.
Custom Color
Mixing Mode
To custom mix a color, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following will show on the display:
•rxxx (red, 0-255)
•gxxx (green, 0-255)
•bxxx (blue, 0-255)
•Axxx (amber, 0-255)
3. Press <ENTER> to cycle through the color settings
4. Use <UP> or <DOWN> to increase or decrease the selected color value.
NOTE: Selecting 0will turn the color off.
5. Repeat steps 3 and 4 until you have your desired color.

Page 14 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
Dimmer Mode
To change or turn off the dimming curve, follow the instructions below:
1. Press <MENU> repeatedly until dIN shows on the display.
2. Press <ENTER> and one of the following will show on the display:
•OFF
•dIN1 (fast dimming curve)
•dIN2 (medium dimming curve)
•dIN3 (slow dimming curve)
3. Use <UP> or <DOWN> to cycle through the dimmer settings.
4. Press <ENTER> to select the desired setting.
IRC-6 Infrared
Remote Control
The SlimBEAM™ QUAD IRC is compatible with the IRC-
6 infrared remote control from
Chauvet.
To run the SlimBEAM™ QUAD IRC in Infrared mode, do the following:
1. Press <MENU> repeatedly until SET shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select either:
•ON to set the product to respond to the IRC-6 remote.
•OFF to set the product to not respond to the IRC-6 remote.
4. Press <ENTER>.
IRC-6 Operation
Be sure the IRC-6 remote is pointing directly at the product and there is nothing in
between the remote and the product.
The following buttons function with this product:
•<BLACK OUT> - Turns LEDs on/off
•<STROBE> - Activates Strobe
•<AUTO>- Activates Auto Program mode, P1–P 10
•<SPEED> - Activates speed control in auto program mode
NOTE: For strobe speed, do not press the speed button
•<SOUND> - Activates Sound mode
•<SENSITIVITY> - Activates sensitivity control in sound-active mode
•<MANUAL> - Activates Custom Color Mixing mode
•<R> - Selects red to be increased or decreased
•<G> - Selects green to be increased or decreased
•<B> - Selects blue to be increased or decreased
•<A> - Selects white to be increased or decreased
•<%> - Selects total output level to be increased or decreased in Custom Color
Mixing mode.
•<FADE> - Activates Auto Program mode, P6–P 9
•<+> - Increases selected value or strobe speed
•<-> - Decreases selected value or strobe speed
•Number Buttons:
<0> - White
<1> - Red
<2> - Orange
<3> - Yellow
<4> - Green
<5> - Cyan
<6> - Blue
<7> - Magenta
<8> - Pink
<9> - Amber
•All other buttons have no function with this product
The IRC-6 will not respond to any inputs when Black Out is activated. If the remote
does not respond when a button is pressed, try pressing <BLACK OUT>. You may
have inadvertently activated Black Out.

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 15 of 19
Master/Slave
Mode
The Master/Slave mode allows a single SlimBEAM™ QUAD IRC
(the master) to control
the actions of one or more SlimBEAM™ QUAD IRC products
(the slaves) without the need
of a DMX controller. The master will be set to operate in either Custom or Sound-Active
mode, or an auto program, while the slave units will be set to operate in Slave mode. Once
set and connected, the slaves will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> repeatedly until one of the DMX modes shows on the display.
2. Press <ENTER> and d 1–d51 will show on the display.
3. Use <UP> or <DOWN> to set the DMX address to d 1.
4. Connect the DMX input of the first slave unit to the DMX output of the master.
5. Connect the DMX input of the subsequent slaves to the DMX output of the previous
slave.
6. Finish setting and connecting all the slaves.
Master unit:
1. Set the master to operate in Custom, Auto, or Sound mode.
2. Make the master unit the first unit in the daisy chain.
•Configure all the slave units before connecting the master to the daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
•
Do not connect more than 31 slaves to the master.

Page 16 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
5.MAINTENANCE
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can lead
to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting product
s at least twice a month.
Howev
er, be aware that usage and environmental conditions could be contributing factors
to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust
collected on the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning
tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 17 of 19
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
10.8 in (273 mm)
3.2 in (80 mm)
8.3 in (212 mm)
5.2 lb (2.4 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
29 W
28 W
Operating Current
0.4 A
0.2 A
Power linking current (units)
0.4 A (18 units)
0.4 A (34 units)
Fuse
T 1 A, 250 V
T 1 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
3 W
50,000 hours
Color
Quantity
Current
Quad-color RGBA
3
1.2 A
Photometrics
Parameter
Beam angle
15°
Strobe Rate
0 to 20 Hz
Illuminance
343 lux @ 2m (per section)
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
4, 9 or 16
Ordering
Product Name
Item Code
UPC Number
SlimBEAM™ QUAD IRC
03050935
781462212834

Page 18 of 19 SlimBEAM™ QUAD IRC User Manual Rev. 1
R
ETURNS
In case you need to get support or return a product:
•If you are located in the U.S., contact Chauvet World Headquarters (see Contact Us).
•If you are located in the UK or Ireland, contact Chauvet Europe Ltd. (see Contact Us).
•If you are located in Mexico, contact Chauvet Mexico (see Contact Us).
•If you are located in Benelux, contact Chauvet Europe BVBA (see Contact Us).
•If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetlighting.com for distributors outside the U.S.,
UK, Ireland, Mexico, or Benelux.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow their instructions on how to return Chauvet
products to them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
Send the merchandise prepaid, in its original box, and with its original packing and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product returned
without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper and
place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

SlimBEAM™ QUAD IRC User Manual Rev. 1 Page 19 of 19
C
ONTACT
U
S
WORLD HEADQUARTERS - Chauvet
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: tec[email protected]
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial
Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.co.uk
MEXICO - Chauvet Mexico
General Information
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: servi[email protected]x
World Wide Web www.chauvet.com.mx
CHAUVET EUROPE - Chauvet Europe BVBA
General Information
Address:Stokstraat 18
9770 Kruishoutem
Belgium
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.eu
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux
contact your dealer. Follow their
instructions to request support or to return a product. Visit our website for contact details.