Chauvet Intimidator COLOR LED User manual

User Manual

Page 2 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
TABLE OF CONTENTS
1. Before You Begin...........................................................................................................3
What Is Included .........................................................................................................................3
Unpacking Instructions................................................................................................................3
Claims.................................................................................................................................................3
Text Conventions ........................................................................................................................3
Symbols......................................................................................................................................3
Disclaimer...................................................................................................................................3
Product at a Glance.....................................................................................................................4
Safety Notes ...............................................................................................................................4
2. Introduction....................................................................................................................5
Overview.....................................................................................................................................5
Dimensions.................................................................................................................................6
3. Setup...............................................................................................................................7
AC Power....................................................................................................................................7
Fuse Replacement...............................................................................................................................7
Mounting.....................................................................................................................................8
Orientation...........................................................................................................................................8
Rigging................................................................................................................................................8
4. Operation........................................................................................................................9
Control Panel Operation..............................................................................................................9
Menu Map...................................................................................................................................9
Configuration (DMX)..................................................................................................................10
Starting Address ................................................................................................................................10
DMX Channel Modes, Assignments, and Values.......................................................................11
Advanced Mode.................................................................................................................................11
Basic Mode........................................................................................................................................13
Configuration (Standalone)........................................................................................................14
Sound-Active Mode............................................................................................................................14
Automatic Modes...............................................................................................................................14
Master/Slave Mode............................................................................................................................15
Manual Pan/Tilt Operation..................................................................................................................16
Pan/Tilt Angle Range.........................................................................................................................16
Display..............................................................................................................................................17
Reset Software ..................................................................................................................................17
Factory Defaults.................................................................................................................................17
Changing Gobos.......................................................................................................................18
5. Technical Information..................................................................................................19
Product Maintenance ................................................................................................................19
6. Technical Specifications..............................................................................................20
Returns.....................................................................................................................................21
Contact Us................................................................................................................................21

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 3 of 21
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator™ Spot LED 450
•Hanging Bracket with Mounting
Hardware
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts
, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention
Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liabil
ity for any errors or
omissions, and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Leon 04/04/13 D. Couppe 04/09/13

Page 4 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Duty Cycle
x
Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or back panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•This product is not intended for permanent installation.
•Keep this User Manual for future use. If you sell the product to another user, be
sure to give this document to the next owner.

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 5 of 21
2.INTRODUCTION
Overview
Button Menu
LCD Screen
Back Panel View
Front Panel View
Power In
Fuse Holder
DMX Out
DMX In

Page 6 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Dimensions
24 in
610 mm
11.9 in
303 mm
16.6 in
423 mm

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 7 of 21
3.SETUP
AC Power
The Intimidator™ Spot LED 450 has an auto-
ranging power supply and it can work with
an input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0–100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with another of the same type and rating.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Intimidator™ Spot LED 450 may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity.
•The rubber feet also serve as floor supports. When mounting the product
on the
floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
Bracket Attachment
Rubber Feet (x4) for floor
mounting without bracket
Bottom Panel View
Side View w/bracket attached

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 9 of 21
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MENU> Selects an operation mode or backs out of the current menu option
<UP> Scrolls up the list of options or selects a higher value
<DOWN>
Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Main Level
Programming Level
Description
DMX Address 001–512 Sets the DMX starting address
Run
Slave Slave operating mode
Fast Automatic mode, fast program
Slow Automatic mode, slow program
Sound Sound-Active mode
Pan
Normal
Normal pan operation
Reverse
Reverse pan operation
Tilt Normal Normal tilt operation
Reverse Reverse tilt operation
Display Bright Display backlight remains on
30Close Display backlight turns off after 30
seconds of control panel inactivity
Pan Angle
540 Pan angle range 540°
360
Pan angle range 360°
180 Pan angle range 180°
Tilt Angle
270
Tilt angle range 270°
180
Tilt angle range 180°
90 Tilt angle range 90°
Channel ADVANCED 14-channel mode
Basic 8-channel mode
Temp. Disp
T1__, T2__, T3__
Displays LED temperature
ResetSystem No Does not reset fixture
Ok Resets fixture
Load Set No Does not load factory defaults
Ok Loads factory defaults

Page 10 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ Spot LED 450 uses up to 14 DMX channels in its ADVANCED
personality, which defines the highest configurable address to 499.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item.
2. If it is not already selected, use <UP> or <DOWN> to select DMX Address.
3. Press <ENTER> and 001–512 shows on the display.
4. Use <UP> or <DOWN> to select the starting address.
5. Press <ENTER>.
DMX
Personalities
The Intimidator™ Spot LED 450 has two DMX personalities. One is a basic 8-channel
personality and the other is a more advanced 14-channel personality.
To select either the basic or advanced personality, do the following:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item.
2. Use <UP> or <DOWN> to select Channel.
3. Press <ENTER> and ADVANCED or Basic shows on the display.
4. Use <UP> or <DOWN> to select ADVANCED for the 14-channel mode or Basic for
the 8-channel mode.
5. Press <ENTER>.

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 11 of 21
DMX Channel Modes, Assignments, and Values
Advanced
Mode
Channel Function Value Setting
1
Pan
000 ó255
0–540°
2
Fine Pan
000 ó255
Fine control of panning
3
Tilt
000 ó255
0–270°
4
Fine Tilt
000 ó255
Fine control of tilting
5
Speed
000 ó255
Pan/Tilt speed (fast to slow)
6 Color Wheel
000 ó007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó063
064 ó066
067 ó078
079 ó092
093 ó107
108 ó120
121 ó136
137 ó152
153 ó170
171 ó212
213 ó255
White
Blue
Yellow
Pink
Green
Red
Light Blue
Orange Red
White
From White to Blue
From Blue to Yellow
From Yellow to Pink
From Pink to Green
From Green to Red
From Red to Light Blue
From Light Blue to Orange Red
Rainbow effect with increasing speed
Reverse rainbow effect with increasing speed
7 Gobo Wheel
064 ó071
072 ó079
080 ó087
088 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó191
192 ó255
Gobo 7 shake with increasing speed
Gobo 6 shake with increasing speed
Gobo 5 shake with increasing speed
Gobo 4 shake with increasing speed
Gobo 3 shake with increasing speed
Gobo 2 shake with increasing speed
Gobo 1 shake with increasing speed
Open
Rainbow effect with increasing speed
Reverse rainbow effect with increasing speed
8 Gobo Rotation
000 ó063
064 ó147
148 ó231
232 ó255
Indexing
Rotation with increasing speed
Reverse rotation with increasing speed
Boomerang with increasing speed
9 Prism
000 ó007
008 ó012
013 ó130
131 ó247
248 ó255
Open
Prism on
Prism rotation with increasing speed
Reverse prism rotation with increasing speed
Static prism effect
10
Focus
000 ó255
Motorized focus, zoom out to zoom in
11
Dimmer
000 ó255
0–100%

Page 12 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
DMX Channel Modes, Assignments, and Values (cont.)
Advanced
Mode
(cont.)
Channel Function Value Setting
12 Shutter
000 ó003
004 ó007
008 ó076
077 ó145
146 ó215
216 ó255
Closed
Open
Strobe effect with increasing speed
Pulse strobe
Random shutter
Open
13 Control Functions
000
ó
007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó135
136 ó143
144 ó151
152 ó159
160 ó255
No function
Blackout while pan/tilt moving
Blackout while moving color wheel
Blackout while moving gobo wheel
Disable blackout while pan/tilt/moving color wheel
Disable blackout while pan/tilt/moving gobo wheel
Disable blackout while moving all options
No function
Reset pan
Reset tilt
Reset color wheel
Reset gobo wheel
Reset gobo rotation
Reset prism
Reset focus
Rest all channels
No function
14 Movement Macros
000 ó007
008 ó023
024 ó039
040 ó055
056 ó071
072 ó087
088 ó103
104 ó119
120 ó135
136 ó151
152 ó167
168 ó183
184 ó199
200 ó215
216 ó231
232 ó247
248 ó255
No function
Automatic movement 1
Automatic movement 2
Automatic movement 3
Automatic movement 4
Automatic movement 5
Automatic movement 6
Automatic movement 7
Automatic movement 8
Sound-active movement 1
Sound-active movement 2
Sound-active movement 3
Sound-active movement 4
Sound-active movement 5
Sound-active movement 6
Sound-active movement 7
Sound-active movement 8

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 13 of 21
DMX Channel Modes, Assignments, and Values (cont.)
Basic Mode
Channel Function Value Setting
1
Pan
000 ó255
0–540°
2
Tilt
000 ó255
0–270°
3 Color Wheel
000 ó007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó063
064 ó066
067 ó078
079 ó092
093 ó107
108 ó120
121 ó136
137 ó152
153 ó170
171 ó212
213
ó
255
White
Blue
Yellow
Pink
Green
Red
Light Blue
Orange Red
White
From White to Blue
From Blue to Yellow
From Yellow to Pink
From Pink to Green
From Green to Red
From Red to Light Blue
From Light Blue to Orange Red
Rainbow effect with increasing speed
Reverse rainbow effect with increasing speed
4 Gobo Wheel
064
ó
071
072 ó079
080 ó087
088 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó191
192 ó255
Gobo 7 shake with increasing speed
Gobo 6 shake with increasing speed
Gobo 5 shake with increasing speed
Gobo 4 shake with increasing speed
Gobo 3 shake with increasing speed
Gobo 2 shake with increasing speed
Gobo 1 shake with increasing speed
Open
Rainbow effect with increasing speed
Reverse rainbow effect with increasing speed
5 Gobo Rotation
000
ó
063
064 ó147
148 ó231
232 ó255
Indexing
Rotation with increasing speed
Reverse rotation with increasing speed
Boomerang with increasing speed
6 Prism
000 ó007
008 ó012
013 ó130
131 ó247
248 ó255
Open
Prism on
Prism rotation with increasing speed
Reverse prism rotation with increasing speed
Static prism effect
7
Focus
000 ó255
Motorized focus, zoom out to zoom in
8 Shutter
000 ó003
004 ó007
008 ó076
077 ó145
146 ó215
216 ó255
Closed
Open
Strobe effect with increasing speed
Pulse strobe
Random shutter
Open

Page 14 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either
Automatic or Sound-Active)
to a DMX string connected to a DMX controller.
Products in standalone
mode may transmit DMX signals that could interfere with
the DMX signals from the controller.
Sound-
Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item.
2. Use <UP> or <DOWN> to select Run.
3. Press <ENTER> and Slave, Fast, Slow or Sound shows on the display.
4. Use <UP> or <DOWN> to select Sound.
5. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Automatic Modes
To enable either of the Automatic modes, follow the instructions below:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item.
2. Use <UP> or <DOWN> to select Run.
3. Press <ENTER> and Slave, Fast, Slow, or Sound shows on the display.
4. Use <UP> or <DOWN> to select Fast (Automatic mode, fast program) or Slow
(Automatic mode, slow program).
5. Press <ENTER>.

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 15 of 21
Master/Slave
Mode
The Master/Slave mode allows a single Intimidator™ Spot LED 450 unit (the “master”) to
control the actions of one or more Intimidator™ Spot LED 450 units (the “slaves”) without
the need of a DMX controller. The master unit will be set to operate in either Automatic or
Sound-Active mode, while the slave units will b
e set to operate in Slave mode. Once set
and connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> and menu items show on the display with a blinking <next to the
selected menu item.
2. Use <UP> or <DOWN> to select Run.
3. Press <ENTER> and Slave, Fast, Slow, or Sound shows on the display.
4. Use <UP> or <DOWN> to select Slave.
5. Press <ENTER>.
6. Connect the DMX input of the first slave unit to the DMX output of the master unit.
7. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
8. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in Fast (Automatic) mode, Slow (Automatic) mode, or
Sound (Sound-Active) mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure all the slave units before connecting the master unit to the DMX
daisy chain.
•Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master
unit.
•Do not connect more than 31 slave units to the master unit.

Page 16 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Manual Pan/Tilt
Operation
To select whether you want the Intimidator™ Spot LED 450 to operate with normal
panning or inverted panning, do the following:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item.
2. Use <UP> or <DOWN> to select Pan.
3. Press <ENTER> and Normal or Reverse shows on the display.
4. Use <UP> or <DOWN> to select Normal pan operation or Reverse (inverse) pan
operation.
5. Press <ENTER>.
To select whether you want the Intimidator™ Spot LED 450 to operate with normal
tilting or inverted tilting, do the following:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item
2. Use <UP> or <DOWN> to select Tilt.
3. Press <ENTER> and Normal or Reverse shows on the display.
4. Press <UP> or <DOWN> to select Normal tilt operation or Reverse (inverse) tilt
operation.
5. Press <ENTER>.
Pan/Tilt Angle
Range
You are able to select the ranges for the pan and tilt angles on the Intimidator™ Spot
LED 450 to achieve the effect you like.
To select the pan angle range, do the following:
1. Press <MENU>and menu items show on the display with a blinking <
next to the
selected menu item.
2. Use <UP> or <DOWN> to select Pan Angle.
3. Press <ENTER> and 540, 360, or 180 shows on the display.
4. Use <UP> or <DOWN> to select either 540 (540° range), 360 (360° range), or 180
(180° range).
5. Press <ENTER>.
To select the tilt angle range, do the following:
1. Press <MENU>and menu items show on the display with a blinking <
next to the
selected menu item.
2. Use <UP> or <DOWN> to select Tilt Angle.
3. Press <ENTER> and 270, 180, or 90 shows on the display.
4. Use <UP> or <DOWN> to select either 270 (270° range), 180 (180° range), or 90
(90° range).
5. Press <ENTER>.

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 17 of 21
Display
You are able to select the length of time the display’s backlight remains on.
To select the time:
1. Press <MENU>and menu items show on the display with a blinking <next to the
selected menu item.
2. Use <UP> or <DOWN> to select Display.
3. Press <ENTER> and Bright or 30Close shows on the display.
4. Use <UP> or <DOWN> to select Bright (the display’s backlight remains on) or
30Close (the display’s backlight turns off after 30 seconds of control panel
inactivity).
5. Press <ENTER>.
Reset Software
To reset the software on the Intimidator™ Spot LED 450, do the following:
1. Press <MENU>and menu items show on the display with a blinking <
next to the
selected menu item.
2. Use <UP> or <DOWN> to select ResetSystem.
3. Press <ENTER> and No or Ok shows on the display.
4. Use <UP> or <DOWN> to select No (does not reset the software settings) or Ok
(resets the software settings).
5. Press <ENTER>.
Factory Defaults
To load the factory default settings on the Intimidator™ Spot LED 450, do the following:
1. Press <MENU> and menu items show on the display with a blinking <
next to the
selected menu item.
2. Use <UP> or <DOWN> to select Load Set.
3. Press <ENTER> and No or Ok shows on the display.
4. Use <UP> or <DOWN> to select No (does not load the factory default settings) or
Ok (loads the factory default settings).
5. Press <ENTER>.

Page 18 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
Changing
Gobos
To change the gobos in the Intimidator™ Spot LED 450,
you do not need to remove
the gobo wheel. Simply:
1. Turn off and disconnect fixture from power outlet.
2. Place the product on a flat, level surface with the top facing up.
3. Access the gobo plate by removing the cover on the moving head. By hand, gently
pry up the right side, and then push right with the indented handles.
NOTE: If you expose the driver board, you are on the wrong side of the head.
Replace the cover immediately and remove the cover on the opposite side of the
moving head.
4. Rotate the gobo wheel until the gobo that needs replacing is accessible.
5. Separate the gobo holder assembly away from the gobo wheel by pushing it
forward and up. Be careful not to push the gobo out of the gobo plate.
6. Extract the gobo holder by pulling it outward (straight up).
7. On a flat surface, remove the expansion ring that holds the gobo in place and
remove the gobo from the gobo plate.
8. Insert a new gobo and hold it in place with the expansion ring.
9. To re-insert the new gobo, slide the tip of the gobo holder under the pressure plate
near the center of the gobo wheel.
10. Push the gobo holder assembly inwards. DO NOT force the gobo holder into the
gobo wheel slot. Slightly move the holder from side-to-side if needed to get it to seat
properly. If correctly installed, the bottom of the holder will be flush with the gobo
wheel.
11. Push cover back into position.
Expansion Ring
Gobo
Gobo Holder
Gobo Wheel Detail Views
Gobo Replacement Diagram
Gobo Holder Removal
Easy-access
Panel

Intimidator™ Spot LED 450 User Manual Rev. 2 Page 19 of 21
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, clean the product at least twice a month. However,
usage and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is at room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grimeto the outside edges of the external optics or
glass/transparent surfaces.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint.
Always dry the glass/transparent surfaces carefully after cleaning them.
Do not spin the cooling fans using compressed air
because you could damage
them.

Page 20 of 21 Intimidator™ Spot LED 450 User Manual Rev. 2
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
16.6 in (423 mm)
11.9 in (303 mm)
24 in (610 mm)
43.6 lbs (19.8 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
400 W
395 W
Operating current
3.3 A
1.7 A
Fuse
F 7 A, 250 V
F 7 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
60 W
50,000 hours
Color
Quantity
Current
White
3
16 A
Photo Optic
Parameter
Illuminance @ 2 m
23,680 lx
Beam angle
19°
Strobe rate
0–20 Hz
Pan and Tilt
540°
270°
Pan/Tilt ranges
540°, 360°, 180°
Pan
270°, 180°, 90°
Tilt
Gobo size
26.75 mm outside
23 mm image
3 mm maximum thickness
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Fan cooled
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
8, 14
Ordering
Product Name
Item Code
UPC Number
Intimidator™ Spot LED 450
08010611
781462209599