Chauvet Lrgrnd 300E Beam User manual

Legend 300E Spot QRG
Page 16
Contact Us World Headquarters
General Information CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support Voice: [phone] (Press 4)
Fax: [phone]
World Wide Web www.chauvetlighting.com
Legend 300E Spot QRG – Rev. 01q
© Copyright 2010 CHAUVET®
All rights reserved
Printed in the P. R. C.
Quick Reference Guide

Legend 300E Spot QRG
Page 2
About this
Guide
The Legend 300E Spot Quick Reference Guide only contains the fixture’s
connection and mounting information as well as the menu options and the
tables with the DMX values.
Disclaimers
This Quick Reference Guide DOES NOT replace the product’s user
manual, which you can download from the CHAUVET® Web site
(www.chauvetlighting.com).
You must read ALL the disclaimers and safety notes in this document
as well as those in the product’s user manual before installing,
operating, or maintaining this product.
Safety
Notes
DO NOT open this fixture unless instructed. It contains no user
serviceable parts.
DO NOT aim this fixture toward any surface closer than 16 feet (5 m).
Otherwise, you may damage or overheat the illuminated surface.
DO NOT aim this fixture toward the Sun. Otherwise, the lenses could
concentrate the solar energy and cause internal overheating.
DO NOT open this fixture within 15 minutes of turning it off to
minimize the risk of lamp explosion.
DO NOT touch the lamp without wearing safety gloves and goggles
because it may explode.
DO NOT look at the light source when this fixture is on.
DO NOT touch the fixture when it is operating because it is very hot.
DO NOT cover the ventilation slots when the fixture is operating to
avoid internal overheating.
DO NOT install or operate this fixture where there is less than 50 cm to
the nearest surface to allow adequate ventilation around it.
DO NOT leave any flammable material within 1 m from this fixture
while operating or connected to the power outlet to minimize the risk of
fire.
DO NOT carry this fixture from the head; use the handles instead.
DO NOT mount this fixture overhead without using a safety cable.
DO NOT operate this fixture outdoors or in places where dust,
excessive heat, water, or humidity may affect it.
DO NOT operate this fixture if you see damage on the housing, lenses,
ultraviolet filter, or cables; have the damaged parts replaced by an
authorized technician at once.
DO NOT connect this fixture to a dimmer or rheostat.
ONLY connect this fixture to a grounded and protected circuit.
What is
Included
One Legend 300E Spot
Three additional gobos
Two omega clamps
One Warranty Card
One Quick Reference Guide
Legend 300E Spot QRG
Page 15
Continued from previous page
MODE 2
(Cont.) Channel Function Value Percent/Setting
28 Color Macro
000 007
008 028
029 049
050 069
070 090
091 110
111 131
132 152
153 173
174 194
195 215
216 235
236 255
Open
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
29 Function
000 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 209
210 229
230 239
240 249
250 255
No function
Enable BO during Pan or Tilt
Disable BO during Pan or Tilt
Enable BO during color change
Disable BO during color change
Enable BO during gobo change
Disable BO during gobo change
Lamp on
Pan / Tilt reset
Color / CMY reset
Gobo 1 / Gobo 2 reset
Shutter reset
Focus / zoom / prism / frost reset
Iris / flatb reset
Reset all
No function
Lamp off
Enable Flatb
Disable Flatb
End of Mode 2

Legend 300E Spot QRG
Page 14
Continued from previous page
MODE 2
(Cont.) Channel Function Value Percent/Setting
25 Pan/Tilt Macro
000 007
008 015
016 023
024 031
032 039
040 047
048 055
056 063
064 071
072 079
080 087
088 095
096 103
104 111
112 119
120 127
128 135
136 143
144 151
152 159
160 167
168 175
176 183
184 191
192 199
200 207
208 215
216 223
224 231
232 239
240 247
248 255
Off
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Macro 13
Macro 14
Macro 15
Macro 16
Macro 17
Macro 18
Macro 19
Macro 20
Macro 21
Macro 22
Macro 23
Macro 24
Macro 25
Macro 26
Macro 27
Macro 28
Macro 29
Macro 30
Macro 31
26 P/T Macro Speed 000 255 Fast~Slow
27 Preset Color
000 021
022 042
043 063
064 085
086 106
107 127
128 148
149 170
171 191
192 212
213 233
234 255
White
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Color 9
Color 10
Color 11
Continues on the next page
Legend 300E Spot QRG
Page 3
Features
21 or 29-channel DMX control, compact, fully electronic, 300-watt
moving yoke spot
Pan: 540⁰
Tilt: 270⁰
Color wheel: Seven colors + white
Split/linear colors
Rainbow color spin at variable speed
Gobo wheel 1: Indexed, rotating gobo wheel with gobo shake
Seven glass, slot-n-lock gobos + open
One multicolor, six black/white
Gobo wheel spin at variable speed
16-bit gobo rotation
Gobo wheel 2: Indexed gobo wheel
Eight metal + open
Gobo wheel spin at variable speed
Static frost
CTC filters (5,600 and 3,200 K)
CMY color mixing system with vector speed adjustments
Three-facet rotating prism
Variable shutter
Variable iris
Variable focus
Variable 16-bit dimming (0~100%)
Linear zoom (16~35º)
Individual reset of pan/tilt, color, gobo, shutter, prism, and focus
Move-in-black for pan/tilt, color, gobo
Remote fixture reset, lamp on/off, and vector speed adjustments
Built-in movement macros with range adjustments
Built-in color macros
Battery powered display
Additional
Features
Three-pin and five-pin DMX connections
User-configurable lamp ignition delay
User-configurable maintenance reminder
Electronic ballast with power factor correction
Electronic power supply
Automatic pan & tilt correction
Pan & tilt locks
Lamp & fixture use timers
Power saver mode
Options W-DMX (wireless DMX) receiver
W-DMX (wireless DMX) transmitter

Legend 300E Spot QRG
Page 4
AC Power This product has an auto-ranging power supply that can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
Fuse
Replacement 1) Turn the power to the fixture off and disconnect it from the power
outlet.
2) With a Philips screwdriver, unscrew the fuse holder out of its housing
and remove the blown fuse from its holder.
3) Replace the blown fuse with a fuse of the exact same type and rating.
4) Replace the fuse holder in its place, and reconnect power.
Mounting Before mounting this product, read the safety notes at the beginning of the
corresponding user manual and follow the mounting
p
rocedure indicated in
it.
Product
Mounting
Diagram
Legend 300E Spot QRG
Page 13
Continued from previous page
MODE 2
(Cont.) Channel Function Value Percent/Setting
15 R-Gobo 1
000 127
128 189
190 193
194 255
Index
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
16 R-Gobo 1 Fine 000 255 0~100%
17 Gobo 2
000 005
006 010
011 015
016 020
021 026
027 031
032 036
037 041
042 047
048 057
058 067
068 077
078 087
088 097
098 107
108 117
118 127
128 189
190 193
194 255
Open
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Gobo 13
Gobo 14
Gobo 15
Gobo 8 Shaking
Gobo 9 Shaking
Gobo 10 Shaking
Gobo 11 Shaking
Gobo 12 Shaking
Gobo 13 Shaking
Gobo 14 Shaking
Gobo 15 Shaking
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
18 Focus 000 255 Near~Far
19 Zoom 000 255 0~100%
20 Prism 000 008
009 255 Normal Prism effect
21 R-Prism 000 127
128 189
190 193
194 255
Index
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
22 R-Prism Fine 000 255 0~100%
23 Iris 000 255 100~0%
24 Frost 000 007
008 255 Normal Frost
Continues on the next page

Legend 300E Spot QRG
Page 12
MODE 2 Channel Function Value Percent/Setting
1Pan 000 255 0~540º
2 Pan Fine 000 255 0~100%
3 Tilt 000 255 0~270º
4 Tilt Fine 000 255 0~100%
5 Pan/Tilt Speed 000 255 Fast~Slow
6 Dimmer 000 255 0~100%
7 Dimmer Fine 000 255 0~100%
8 Shutter
000 007
008 015
016 131
132 167
168 203
204 239
240 247
248 255
Black out
Open
Slow~Fast
Slow open / fast close
Fast open / slow close
Slow open / slow close
Random strobe
Open
9 Color
000 007
008 015
016 023
024 031
032 039
040 047
048 055
056 063
064 127
128 189
190 193
194 255
White
Red
Orange
3,200 K
5,600 K
Pink
Green
Dark Blue
Color Mix
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
10 Cyan 000 255 0~100%
11 Magenta 000 255 0~100%
12 Yellow 000 255 0~100%
13 CMY Speed 000 255 Fast~Slow
14 Gobo 1
000 007
008 014
015 021
022 028
029 035
036 042
043 049
050 057
058 067
068 077
078 087
088 097
098 107
108 117
118 127
128 189
190 193
194 255
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 1 Shaking
Gobo 2 Shaking
Gobo 3 Shaking
Gobo 4 Shaking
Gobo 5 Shaking
Gobo 6 Shaking
Gobo 7 Shaking
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
Continues on the next page
Legend 300E Spot QRG
Page 5
Gobo
Wheels The Legend 300E Spot comes with two gobo wheels. Gobo wheel #1 has
seven rotating gobos, while gobo wheel #2 has eight fixed gobos, as
indicated below. The diagram shows the first and last gobo on each wheel,
as per the DMX Values tables.
Rotating Gobos Fixed Gobos
Extra
Gobos
Color
Wheel
178
15

Legend 300E Spot QRG
Page 6
Replacing a
Gobo
1) Turn the fixture off and disconnect it from the power outlet.
2) Open the head cover by loosening the four fastening screws at the sides
of the top cover.
3) Separate the gobo plate away from Gobo Wheel 1 by pushing it toward
the front of the moving head (direction 1 in the diagram). Be careful not
to push the gobo out of the gobo plate.
4) Extract the gobo plate l by pulling it outward (direction 2 in the
diagram).
5) On a flat surface, remove the expansion ring that holds the gobo in
place and remove the gobo from the gobo plate.
6) Insert a new gobo and hold it in place with the expansion ring.
7) Slide the tip of the gobo plate under the pressure plate near the center of
Gobo Wheel 1.
8) Push the gobo plate inwards. DO NOT force the gobo plate into the
gobo wheel slot. If correctly installed, the gobo plate should
accommodate itself in the gobo wheel slot.
Legend 300E Spot QRG
Page 11
Continued from previous page
MODE 1
(Cont.) Channel Function Value Percent/Setting
15 Focus 000 255 Near~Far
16 Zoom 000 255 0~100%
17 Prism 000 008
009 255 Normal Prism effect
18 R-Prism
000 127
128 189
190 193
194 255
Index
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
19 Iris 000 255 0~100%
20 Frost 000 255 0~100%
21 Function
000 069
070 079
080 089
090 099
100 109
110 119
120 129
130 139
140 149
150 159
160 169
170 179
180 189
190 199
200 209
210 229
230 239
240 249
250 255
No function
Enable BO during Pan or Tilt
Disable BO during Pan or Tilt
Enable BO during color change
Disable BO during color change
Enable BO during gobo change
Disable BO during gobo change
Lamp on
Pan / Tilt reset
Color / CMY reset
Gobo 1 / Gobo 2 reset
Shutter reset
Focus / zoom. / prism / frost reset
Iris / flatb reset
Reset all
No function
Lamp off
Enable flatb
Disable flatb
End of Mode 1

Legend 300E Spot QRG
Page 10
Continued from previous page
MODE 1
(Cont.) Channel Function Value Percent/Setting
8 Color
(Cont.)
064 127
128 189
190 193
194 255
Color Mix
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
9 Cyan 000 255 0~100%
10 Magenta 000 255 0~100%
11 Yellow 000 255 0~100%
12 Gobo 1
000 007
008 014
015 021
022 028
029 035
036 042
043 049
050 057
058 067
068 077
078 087
088 097
098 107
108 117
118 127
128 189
190 193
194 255
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 1 Shaking
Gobo 2 Shaking
Gobo 3 Shaking
Gobo 4 Shaking
Gobo 5 Shaking
Gobo 6 Shaking
Gobo 7 Shaking
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
13 R-Gobo 1
000 127
128 189
190 193
194 255
Index
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
14 Gobo 2
000 005
006 010
011 015
016 020
021 026
027 031
032 036
037 041
042 047
048 057
058 067
068 077
078 087
088 097
098 107
108 117
118 127
128 189
190 193
194 255
Open
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Gobo 13
Gobo 14
Gobo 15
Gobo 8 Shaking
Gobo 9 Shaking
Gobo 10 Shaking
Gobo 11 Shaking
Gobo 12 Shaking
Gobo 13 Shaking
Gobo 14 Shaking
Gobo 15 Shaking
Fast~Slow CW rotation
Stop
Slow~Fast CCW rotation
Continues on the next page
Legend 300E Spot QRG
Page 7
Replacing
the Lamp
1) Turn the fixture off and disconnect it from the power outlet.
2) Wait at least 15 minutes for the lamp to cool down.
3) Loosen the two screws on the lamp cover (marked “A” in the diagram).
4) Lift and rotate the lamp cover as per the diagram to expose the base of
the lamp.
5) Rotate the ceramic base of the lamp 90º counterclockwise.
6) Pull the lamp out by holding it from its base only.
7) Insert the new lamp and turn it 90º clockwise.
8) Reverse steps 3 and 4.
9) Use the adjustment screws (marked “B” in the diagram) to position the
lamp in the center of the reflector to obtain the best output.
Increasin
g
the
Lamp’s Life
ALWAYS turn the lamp off by using the DMX controller or the
fixture’s control panel. Then wait at least five minutes before switching
off the fixture. This will keep the fans running to extract any remaining
heat from the fixture’s head.
DO NOT power cycle the fixture unless it is necessary.
DO NOT touch the lamp without wearing gloves to avoid leaving
grease on the bulb or on the contacts that could reduce the lamp’s life.
ALWAYS change the lamp when it has reached its recommended
lifespan to avoid the risk of lamp explosion.

Legend 300E Spot QRG
Page 8
Menu Options
Main Level 2n
d
Level 3r
d
Level 4
th
Level
DMX Functions
DMX Address 001~512
N/A
DMX Channel Mode Mode 1 (21-channel)
Mode 2 (29-channel)
View DMX Value N/A
WDMX Setting
(Requires optional W-DMX
receiver)
Active No/Yes
Retransmit
Reset Memory
Fixture Setting
Pan Inverse
No/Yes N/A
Tilt Inverse
Bl. o P/T Moving
Bl. O Color Change
Bl. O Gobo Change
Lamp Setting
On/Off On/Off
N/A
State/Power On
Off Via DMX No/Yes
On if DMX On
Off if DMX Off
Cooling Mode Auto/High
Ignition Delay 0~255 s
Low Power Delay 0~255 s
Display Setting
Display Inverse No/Yes N/A
Backlight Auto Off
Backlight Intensity 1~10
Temperature Unit ºC/ºF
Fixture Test Auto Test N/A N/A
Manual Test
Fixture Information Fixture Use Time N/A N/ALamp On Time Exit/Rest Time
Firmware Version N/A
Reset Functions
Pan/Tilt
No/Yes N/A
Color/CMY
Gobo
Shutter/Dimmer
Focus/Zoom/Prism/Frost
Iris/Flatb
All
Special Functions Fixture Maintenance Interval/Remain Time N/A
Factory Setting No/Yes
Legend 300E Spot QRG
Page 9
Offset
Menu
Pan -128~127 R-Gobo 2 -128~127
Tilt -128~127 Gobo 2 -128~127
Shutter 0~255 Prism 0~255
Dimmer 0~255 R-Prism -128~127
Color -128~127 Frost 0~255
Cyan 0~255 Flatb 0~255
Magenta 0~255 Focus 0~255
Yellow 0~255 Zoom 0~255
Gobo 1 -128~127
Control
Panel
Description
Button Function
<MENU> Exits from the current menu or function
<ENTER> Enables the currently displayed menu or sets the currently
selected value into the selected function
<UP> Navigates upwards through the menu list and increases the
numeric value when in a function
<DOWN> Navigates downwards through the menu list and decreases the
numeric value when in a function
DMX Values
MODE 1 Channel Function Value Percent/Setting
1Pan 000 255 0~540º
2 Pan Fine 000 255 0~100%
3 Tilt 000 255 0~270º
4 Tilt Fine 000 255 0~100%
5 Pan/Tilt Speed 000 255 Fast~Slow
6 Dimmer 000 255 0~100%
7 Shutter
000 007
008 015
016 131
132 167
168 203
204 239
240 247
248 255
Black out
Open
Slow~Fast
Slow open/Fast close
Fast open/Slow close
Slow open/Slow close
Random strobe
Open
8 Color
000 007
008 015
016 023
024 031
032 039
040 047
048 055
056 063
White
Red
Orange
3,200 K
5,600 K
Pink
Green
Dark Blue
Continues on the next page