Chiayo Coach Pro 500 User manual

ISO 9001:2008
Personal Wireless Portable Ampler
Operation Manual
CHIAYO

-1-
● Coach Pro 500 operating instruction
Congratulation and thank you for the purchase of this all-in-one ultra compact portable
sound system. To ensure a trouble-free operation, please read this manual thoroughly to
fully understand its controls and functions.
Coach Pro 500 can be equipped with 1 wireless receiver module. This receiver module can
be either VHF or UHF. The VHF module is a 󰘰xed crystal single frequency type whereas
the UHF module is a PLL synthesized type with 16 preset frequencies (identi󰘰ed by
external 16 channel rotary switch(s)) or 󰘰xed crystal single frequency.
● Con󰘰guration:
All versions of Coach Pro 500 series comes equipped with the following:
1. Mini wired microphone (DM-555)
2. Shoulder strap
3. Switch mode power supply
4. Operation manual
● Optional accessories:
1. Wireless handheld or beltpack transmitter
2. Charger for UHF transmitter
3. Tripod stand (ST-30)
4. Storage bag (SB-61)
● Matching transmitter
band handheld transmitter beltpack transmitter
UHF SQ-1016(16 freq.)
SQ-1016V(16 freq.+volume control)
Q-815(󰘰xed freq.)
SM-1016(16 freq.)
M-815(󰘰xed freq.)
VHF Q-1005 M-1005
Remark: Manufacturer reserves the rights to change the above combinations without prior
notice.

-2-
Coach Pro 500 Rear control panel
● Parts and function
1. USB port
2. LCD display
3. Play/Pause
4. Play mode: Short press to switch between "repeat all", "repeat single" and "play
random". Press for 1-2 seconds to change "EQ" modes.
5. Skip forward
6. Skip backward
7. Folder forward
8. Folder backward
9. Remote sensor
10. Power and volume control of wireless microphone
11. Channel selector
12. RF signal indicator
13. Echo control
14. Emergency alarm(2 sounds for selection)
15. Master volume control
16. Tone control
17. Volume control of audio input/USB
18. Power/Battery low indicator: Normal(GREEN)/battery low(RED)
19. Power on-o󰘯/Volume control of wired microphone
20. Charging indicator: During charging(RED)/Charging 󰘰nished(GREEN)
21. DC in
22. Aux output
23. Aux input
24. Wired microphone input
14
11
16
21
26
12
17
22
3
8
13
18
23
5
9
14 19
24
7
10
15
20

-3-
● Recharge its inbuilt Lithium battery before 󰘰rst use
After unpacking the unit for the 󰘰rst time, please charge the unit for about 4~5 hours before
any operation. This is absolutely necessary as the built-in rechargeable battery might have
been discharged naturally due to long shipment and storage time, even though it has been
fully charged in the factory prior to shipment.
To charge the battery, just plug in the DC end of the switch mode power supply into the
DC IN of the unit and charging will start automatically. During the charging process, the
charging indicator LED will be RED. When this LED turns GREEN, this battery is then fully
charged.
● Operating procedures
To operate this portable sound unit, switch on the main POWER switch, which will be
GREEN. If it turns RED, its battery power might be too low and recharging is necessary.
The main power switch does not switch on the wireless microphone and USB digital player
as each of them has dedicated Power / Volume control.
● Operating the built-in wireless microphone system
To use the wireless microphone, 󰘰rst switch on the main power switch, then switch on the
WR power/volume control switch. Switch on the corresponding transmitter and set this
system to the same frequency and RF signal LED will grow.
● Operating the dynamic wired microphone
There is a MIC IN jack with dedicated volume control for this portable sound unit. To use
a cable microphone (dynamic only), just plug the end with a phone jack plug into MIC IN .
Switch on the Power / volume control knob MIC and rotate it to adjust the volume.
● Operating the USB Digital Player
To use the USB Digital Player, 󰘰rst switch on the main power switch, then switch on the
AUX/USB power/volume control switchand rotate it to adjust the volume. Plug USB into the
port and begin your misic playing and setting.
How to use each buttons of this digital player:
▲
II: Press to play/pause the music.
▲
: Press to skip forward.
▲
: Press to skip backward.
▲ ▲
: Press to skip folders forward.
▲ ▲
: Press to skip folders backward.
MODE: Short press to switch between "repeat all", "repeat single" and "play random".
Press for 1-2 seconds to change "EQ" modes.

-4-
UHF handheld microphone Q-815
● Parts and functions
1. Microphone module and ballscreen
2. Power/Battery low indicator
3. Power switch
4. Battery cover
● Battery installation
This microphone requires 2 AA-size batteries to operate. Please insert the batteries
according to the correct polarity. Many batteries are known to have leakage problem of
conductive and corrosive liquid. Please observe the rule to remove the batteries if they are
not to be used for a longer period.
1 2 3 4
UHF handheld microphone SQ-1016/SQ-1016V
● Parts and functions
1. Microphone module and ballscreen
2. Power/Battery low indicator
3. Power switch
4. Channel selector
5. Battery cover
6. Charging port
7. Volume control (SQ-1016V)
● Battery installation
This microphone requires 2 AA-size batteries to operate. Please insert the batteries
according to the correct polarity. Many batteries are known to have leakage problem of
conductive and corrosive liquid. Please observe the rule to remove the batteries if they are
not to be used for a longer period.
● Channel setting
Use the attached small screw driver to set the channel and the channel number will show
on the window above it.
1 2 3 4 5
6
7

-5-
UHF beltpack transmitter SM-1016
● Parts and functions
1. Antenna
2. Power/Battery low indicator
3. Power switch
4. Mini XLR connector
5. Release buttons of battery compartment
6. Battery cover
7. Lavalier microphone
8. Charging contacts
9. Channel selector
10. Gain control (GT, hign impedance)
11. Gain control (MT, low impedance)
● Battery installation
This microphone requires 2 AA-size batteries to operate. Please insert the batteries
according to the correct polarity. Many batteries are known to have leakage problem of
conductive and corrosive liquid. Please observe the rule to remove the batteries if they are
not to be used for a longer period.
● Channel and sensitivity setting
Use the attached small screw driver to set the channel and the channel number will show
on the window above it.
Gain control is an adjustable design that enables user to set di󰘯erent output levels. GT is
for the use of instrument with high impedance, such as guitar while MT is for the use of low
impedance such as lavalier or headset microphone. To adjust the audio input levels, simply
use a small screw driver to rotate to a desired level.
1
2 3 4
5
6
7 8
9
10 11
VHF handheld microphone Q-1005
● Parts and functions
1. Microphone module and ballscreen
2. Power/Battery low indicator
3. Power switch
4. Battery cover
● Battery installation
This microphone requires 2 AA-size batteries to operate. Please insert the battery
according to the correct polarity. Many batteries are known to have leakage problem of
conductive and corrosive liquid. Please observe the rule to remove the battery if it's not to
be used for a longer period.
1 2 3 4

-6-
UHF beltpack transmitter M-815
VHF beltpack transmitter M-1005
● Parts and functions
1. Antenna
2. Power/Battery low indicator
3. Power switch
4. Mini XLR connector
5. Release buttons of battery compartment
6. Battery cover
7. Lavalier microphone
8. Charging contacts
9. Gain control (GT, hign impedance)
10. Gain control (MT, low impedance)
● Battery installation
This microphone requires 2 AA-size batteries to operate. Please insert the batteries
according to the correct polarity. Many batteries are known to have leakage problem of
conductive and corrosive liquid. Please observe the rule to remove the batteries if they are
not to be used for a longer period.
● Sensitivity setting
Gain control is an adjustable design that enables user to set di󰘯erent output levels. GT is
for the use of instrument with high impedance, such as guitar while MT is for the use of low
impedance such as lavalier or headset microphone. To adjust the audio input levels, simply
use a small screw driver to rotate to a desired level.
1
2 3 4
5
6
78
910

Web site: http://www.chiayo.com.tw E-mail: [email protected]
Ofce: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan / Tel: [phone] Fax: [phone]
Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan / Tel: [phone] Fax: [phone]
12I1244