Cineversum Black Wind Four R599782 User manual

2 R599782 - Blackwing Four User Manual
Changes
Cineversum provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular purpose. Cineversum may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the
information in this publication; these changes are incorporated in new editions of this publication.
Copyright
All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Cineversum.
Guarantee
Cineversum provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. Cineversum must be informed immediately in writing of
any complaints.
If the purchaser or third party caries out modifications or repairs on goods delivered by Cineversum, or if the goods
are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of
risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will
be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or
special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance
are not subject to the guarantee provided by Cineversum either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must
be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of
their respective holders. All brands and product names mentioned in this manual serve as comments or examples
and are not to be understood as advertising for the products of their manufactures.

R599782 - Blackwing Four User Manual 3
TABLE OF CONTENTS
1.0 SAFETY INSTRUCTIONS ............................................................................................. 5
1.1 Important information........................................................................................................................ 5
Lead-free regulation ............................................................................................................5
Information for Users on Disposal of Old Equipment ........................................................ 5
About the installation place................................................................................................. 5
1.2 Important safeguards.......................................................................................................................... 5
1.3 REGIONAL SPECIFIC INFORMATION......................................................................................... 7
FCC INFORMATION (USA ONLY) ................................................................................. 7
2.0 INSTALLATION GUIDELINES .................................................................................... 8
2.1 Environment of Use ........................................................................................................................... 8
Mounting this unit to the ceiling ......................................................................................... 8
Precautions of Usage........................................................................................................... 8
2.2 Air-Flow and Space Requirements .................................................................................................... 8
2.3 Ceiling mounting the unit .................................................................................................................. 9
Precautions for Ceiling-mount ............................................................................................ 9
2.4 Projection Distance and Offset Setting............................................................................................ 10
Projection Distance ........................................................................................................... 10
Projector position : setting the correct lens shift............................................................... 10
Adjust the picture Focus.................................................................................................... 12
Adjust the picture Zoom.................................................................................................... 12
3.0 REMOTE CONTROL UNIT (RCU) ............................................................................ 13
3.1 General view .................................................................................................................................... 13
3.2 Loading and replacing batteries....................................................................................................... 13
3.3 How to use the remote control unit.................................................................................................. 14
4.0 GETTING STARTED .................................................................................................... 15
4.1 General View ................................................................................................................................... 15
Front side........................................................................................................................... 15
Rear side............................................................................................................................ 15
Input Panel side ................................................................................................................. 15
4.2 Connecting the Power Cord............................................................................................................. 16
4.3 Operating LEDs ............................................................................................................................... 17
4.4 Operating and Navigation Buttons .................................................................................................. 18
5.0 CONNECTIONS............................................................................................................. 18
5.1 Connecting a device to the projector ............................................................................................... 19
5.2 Connecting a SCART device ........................................................................................................... 20
5.3 Caution when connecting a device .................................................................................................. 20
6.0 MENU AND PICTURE SETTING............................................................................... 21
6.1 Menu Structure ................................................................................................................................ 21
6.2 Picture Adjust menu......................................................................................................................... 24
Picture Mode ..................................................................................................................... 24
Contrast ............................................................................................................................. 24
Brightness.......................................................................................................................... 24
Color.................................................................................................................................. 24
Tint .................................................................................................................................... 24
Color Temperature............................................................................................................. 24
Gamma .............................................................................................................................. 24
Advanced........................................................................................................................... 25
Lens Aperture .................................................................................................................... 25
Reset.................................................................................................................................. 25
6.3 Input Signal menu............................................................................................................................ 26
HDMI Inputs .....................................................................................................................26
Component ........................................................................................................................ 26
Video / S-Video .................................................................................................................26
PC...................................................................................................................................... 26

4 R599782 - Blackwing Four User Manual
Picture Position ................................................................................................................. 26
Aspect Ratio ...................................................................................................................... 26
V-Stretch (for Video sources)............................................................................................ 27
Over Scan (only SD) and Mask (only HD)....................................................................... 28
Film Mode (only 480i, 576i, 1080i).................................................................................. 28
6.4 Installation Menu ............................................................................................................................. 28
Lens Control...................................................................................................................... 28
Pixel Adjust ....................................................................................................................... 28
Installation Style................................................................................................................ 29
Keystone............................................................................................................................ 29
Screen Adjust .................................................................................................................... 29
6.5 Display Setup Menu......................................................................................................................... 29
Back Color ........................................................................................................................ 29
Menu Position ...................................................................................................................29
Menu Display ....................................................................................................................29
Line Display ...................................................................................................................... 29
Source Display ..................................................................................................................29
Logo .................................................................................................................................. 29
Language ........................................................................................................................... 29
6.6 Function Menu................................................................................................................................. 29
Lamp Power ......................................................................................................................29
Test Pattern........................................................................................................................ 30
Off-Timer .......................................................................................................................... 30
High Altitude Mode........................................................................................................... 30
6.7 Information Menu ............................................................................................................................ 30
Input Source ...................................................................................................................... 30
Source................................................................................................................................ 30
Resolution ......................................................................................................................... 30
H. Frequency ..................................................................................................................... 30
V. Frequency ..................................................................................................................... 30
Deep Color ........................................................................................................................ 30
Lamp Time ........................................................................................................................ 30
6.8 Expert Calibration............................................................................................................................ 30
7.0 ANAMORPHIC LENS .................................................................................................. 31
7.1 Optional 2.35 CineMax and 2.35 THEATRE Concept.................................................................... 31
7.2 Using the Remote Control Unit. ...................................................................................................... 31
7.3 2.35 CineMax and 2.35 CineMax PRO options .............................................................................. 32
7.4 2.35 THEATER Concept ................................................................................................................. 32
8.0 MAINTENANCE............................................................................................................ 34
8.1 Clean Dirt on the Cabinet ................................................................................................................ 34
8.2 Dirt on the Lens ............................................................................................................................... 34
8.3 Replacing the Lamp ......................................................................................................................... 34
Light-source Lamp and Lamp Usage Time....................................................................... 34
Procedure for Lamp Replacement..................................................................................... 34
Resetting Lamp Time ........................................................................................................ 35
8.4 Cleaning and Replacing the Dust Filters ......................................................................................... 35
8.5 Troubleshooting ............................................................................................................................... 35
9.0 MISCELLANEOUS ....................................................................................................... 37
9.1 RS-232 input and IR Codes ............................................................................................................. 37
9.2 PC compatible signals...................................................................................................................... 41
9.3 Specifications.................................................................................................................................. 43

1.0 SAFETY INSTRUCTIONS
R599782 - Blackwing Four User Manual 5
1.0 SAFETY INSTRUCTIONS
1.1 Important information
Lead-free regulation
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains
lead in some components.
Disposal of these materials may be regulated in your community due to environmental considerations. For disposal
or recycling information please contact your local authorities, or the Electronics Industries Alliance: http://
www.eiae.org.
Information for Users on Disposal of Old Equipment
This symbol indicates that the electrical and electronic equipment should not be disposed as general
household waste at its end of life. Instead, the product should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment for proper treatment, recovery
and recycling in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will help
prevent potential negative effects on the environment and human health which could otherwise be caused by
inappropriate waste handling of this product.
For more information about collection point and recycling of this product, please contact your local municipal office,
your household waste disposal service or the shop where you purchased the product. Penalties may be applicable
for incorrect disposal of this waste, in accordance with national legislation.
Other Countries outside the European Union:
If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules
in your country for the treatment of old electrical and electronic equipment.
About the installation place
Do not install the projector in a place that cannot support its weight securely.
If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.
1.2 Important safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for
its installation, use and service.
Please read these Important Safeguards carefully before use.
• All the safety and operating instructions should be read before the product is operated.
• All warnings on the product and in the operating instructions should be adhered to.
• All operating instructions should be followed.
• Place the projector near a wall outlet where the plug can be easily unplugged.
•Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
• Do not use attachments not recommended by the product manufacturer as they may be hazardous.
•Do not use this product near water. Do not use immediately after moving from a low temperature to high
CAUTION:
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel. This
projector is equipped with a 3-blade grounding type plug to satisfy FCC rule. If you are unable to insert the plug
into the outlet, contact your electrician.
WARNING:
To prevent fire or shock hazards, do not expose this appliance to rain or moisture. This apparatus must be
earthed.
The power input is auto-ranging from 100 to 240 VAC.

1.0 SAFETY INSTRUCTIONS
6 R599782 - Blackwing Four User Manual
temperature, as this causes condensation, which
may result in fire, electric shock, or other
hazards.
•Do not place this product on an unstable cart,
stand, or table. The product may fall, causing
serious injury to a child or adult, and serious
damage to the product. The product should be
mounted according to the manufacturer’s
instructions, and should use a mount
recommended by the manufacturer.
•When the product is used on a cart, care should
be taken to avoid quick stops, excessive force,
and uneven surfaces which may cause the
product and cart to overturn, damaging
equipment or causing possible injury to the
operator.
•Slots and openings in the cabinet are provided
for ventilation. These ensure reliable operation of
the product and protect it from overheating.
These openings must not be blocked or covered.
(The openings should never be blocked by
placing the product on bed, sofa, rug, or similar
surface. It should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided and the
manufacturer’s instructions have been adhered
to). For proper ventilation, separate the product
from other equipment, which may prevent
ventilation and keep a distance of more than 5-9”
(150 mm).
•This product should be operated only with the
type of power source indicated on the label. If you
are not sure of the type of power supply to your
home, consult your product dealer or local power
company.
•This product is equipped with a three-wire plug.
This plug will fit only into a grounded power
outlet. If you are unable to insert the plug into the
outlet, contact your electrician to install the
proper outlet. Do not defeat the safety purpose of
the grounded plug.
•Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular
attention to cords at doors, plugs, receptacles,
and the point where they exit from the product.
•For added protection of this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet and disconnect the cable system. This
will prevent damage to the product due to
lightning and power line surges.
•Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as
this can result in a risk of fire or electric shock.
•Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
•Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltages and other hazards. Refer all
service to qualified service personnel.
•Unplug this product from the wall outlet and refer
service to qualified service personnel under the
following conditions:
a) When the power supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have fallen
on the product.
c) If the product has been exposed to rain or
water.
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the Operation
Manual, as an improper adjustment of controls may
result in damage and will often require extensive
work by a qualified technician to restore the product
to normal operation.
e) If the product has been dropped or damaged in
any way.
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
•When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or with same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.
•Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
•The product should be placed more than one foot
away from heat sources such as radiators, heat
registers, stoves, and other products (including
amplifiers) that produce heat.
•When connecting other products such as VCR’s,
and personal computers, you should turn off the
power of this product for protection against
electric shock.
•Do not place combustible behind the cooling fan.
For example, cloth, paper, matches, aerosol cans
or gas lighters that present special hazards when
over heated.
•Do not look into the projection lens while the
illumination lamp is turned on. Exposure of your
eyes to the strong light can result in impaired
eyesight.
•Do not look into the inside of this unit through
vents (ventilation holes), etc. Do not look at the
illumination lamp directly by opening the cabinet
while the illumination lamp is turned on. The
illumination lamp also contains ultraviolet rays
and the light is so powerful that your eyesight can
be impaired.
•Do not drop, hit, or damage the light-source lamp
(lamp unit) in any way. It may cause the light-
source lamp to break and lead to injuries. Do not
use a damaged light source lamp. If the light-
source lamp is broken, ask your dealer to repair

1.0 SAFETY INSTRUCTIONS
R599782 - Blackwing Four User Manual 7
it. Fragments from a broken light-source lamp may cause injuries.
•The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the
light source lamp. If anything is unclear, please consult your dealer.
•Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the
projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal
injury.
• Use only the accessory cord designed for this product to prevent shock.
•The power supply voltage rating of this product is AC120 V, AC100 V – AC240 V, the power cord attached
conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure
Safety and EMC.
• When it is used by other power supply voltage, power cable must be changed.
•Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult
your product dealer.
•Caution: Do not allow any unqualified person to install the unit. Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation
is performed by an unqualified person, it may cause personal injury or electrical shock.
1.3 REGIONAL SPECIFIC INFORMATION
FCC INFORMATION (USA ONLY)
Changes or modification not approved by Cineversum could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encourage to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC
The Federal Communications Commission (FCC) is an independent United States government agency, created,
directed, and empowered by Congressional statute.
The FCC was established by the Communications Act of 1934 as the successor to the Federal Radio Commission
and is charged with regulating all non-Federal Government use of the radio spectrum, including radio and television
broadcasting, and all interstate telecommunications like wire, satellite and cable as well as all international
communications that originate or terminate in the United States. The FCC's jurisdiction covers the 50 states, the
District of Columbia, and U.S. possessions.

2.0 INSTALLATION GUIDELINES
8 R599782 - Blackwing Four User Manual
2.0 INSTALLATION GUIDELINES
2.1 Environment of Use
• Do not use this unit in rooms with cigarette smoke or oily smoke. This may cause the unit to malfunction.
Mounting this unit to the ceiling
Check temperature around the unit. When a heater is in use, the ceiling may reach a temperature higher than
anticipated, hence leading to malfunction of the unit.
Precautions of Usage
This unit makes use of a light source lamp that may reach a high temperature during projection. Do not allow
projection under the following conditions. Doing so may cause fire or malfunction of the unit.
• Projection with the unit laid on sides.
•Projection with the unit installed in an unreasonable angle. Avoid using this unit at an angle of more than 15°
horizontally and 5° vertically. Doing so may cause unevenness in the color or shorten the lamp life.
• Projection at a location that blocks the air inlets or exhaust vents.
• Projection at a place exposed to air blasts from an air conditioner.
2.2 Air-Flow and Space Requirements
This unit can be installed in table, ceiling, rear table or rear ceiling position. Make sure that the unit is installed within
the space requirements described below.
•A: Air inlets
•B: Air outlet
Air flow
A
A
B
Chasis Filter

2.0 INSTALLATION GUIDELINES
R599782 - Blackwing Four User Manual 9
Space requirements
2.3 Ceiling mounting the unit
When mounting of this unit is required, make use of the 4 screw holes (M5x20 screws) at the bottom of this
unit indicated by the letter A. Allow sufficient space around the air inlets to avoid blocking them.
Precautions for Ceiling-mount
•To ceiling-mount this unit, special expertise and techniques are necessary.
Be sure to ask your dealer or specialist to perform mounting.
• Do not mount at places that may be subjected to vibration and shock.
•Depth of the screw holes (A) is 22 mm. Do not use long screws as you may
damage inside the projector.
•Install at a safe place in case this unit or a part of it may drop. If the light-
source lamp is broken, small pieces of glass from the mesh of the filter
may appear outside the unit.
•Regardless whether the unit is still under guarantee, Cineversum is not
liable for any product damage caused by mounting the unit with third party
ceiling mount or when the environment is not suitable for ceiling-mount.
200 mm
300 mm
300 mm
300 mm
300 mm
AA
AA

2.0 INSTALLATION GUIDELINES
10 R599782 - Blackwing Four User Manual
2.4 Projection Distance and Offset Setting
Projection Distance
•The projection screen sizes and projecting distances in the table above are provided only as a guide. Please use
them as reference during installation.
• Use a projection image of 16:9 aspect ratio for setup adjustment.
Projector position : setting the correct lens shift
The optimum image can be obtained when the centre of this projector’s lens and the screen are placed
perpendicular to each other. Take note of the projection angle when placing them. You can also use up to +/- 15° up
and down position and configure trapezoidal correction.
Projection Screen Size
Diagonal size
(Aspect Ratio 16:9)
Projection Screen Size
Base size
(Aspect Ratio 16:9)
Projection Screen
Height
(Aspect Ratio 16:9)
Blackwing Four
Projecting Distance
minimum - maximum
50" (1270 mm) 43,6" (1107 mm) 24,5" (623 mm) 151 cm - 305 cm
60" (1524 mm) 52,3" (1328 mm) 29,4" (747 mm) 178 cm - 366 cm
70" (1778 mm) 61,0" (1550 mm) 34,3" (872 mm) 209 cm - 428 cm
83" (2108 mm) 72,3" (1837 mm) 40,7" (1034 mm) 251 cm - 507 cm
92" (2337 mm) 80,2" (2037 mm) 45,1" (1146 mm) 279 cm - 562 cm
100" (2540 mm) 87,2" (2214 mm) 49,0" (1245 mm) 301 cm - 613 cm
110" (2794 mm) 95,9" (2435 mm) 53,9" (1370 mm) 331 cm - 675 cm
138" (3505 mm) 120,3" (3055 mm) 67,7" (1718 mm) 418 cm - 843 cm
150" (3810 mm) 130,7" (3321 mm) 73,5" (1868 mm) 453 cm - 860 cm
180" (4572 mm) 156,9" (3985 mm) 88,2" (2241 mm) 545 cm - 1107 cm
200" (5080 mm) 174,3" (4428 mm) 98,1" (2491 mm) 6060 cm - 1230 cm
This unit comes with a vertical and horizontal shift to suit most installations. Make sure that your installation
does not exceed 80% vertical offset and 34% horizontal offset to avoid trapezoidal correction.
Screen Height
(H)
Screen Base (B)
Horizontal Shift +/- 34%
Vertical Shift
+/- 80%

2.0 INSTALLATION GUIDELINES
R599782 - Blackwing Four User Manual 11
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen position.
Adjust the picture to your screen.
• The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).
• The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).
•The shift level is set to 0% vertically and horizontally by default, that means that the optical lens is aligned with
the center of the screen.
• If the projector is not installed vertically, use trapezoidal Correction to fulfill your screen.
•If you plan to use both the vertical and horizontal shifts, make sure to not exceed the values contained in the tab
below:
2.4.0.1 Adjust the picture position
The Blackwing Four projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens
Control] setting into the [Installation] menu, select the shift adjustment. Or use the direct access button on the
Remote Control Unit [LENS] to make the lens control adjustment.
You can use self-generated test pattern of the projector or an external pattern, from a calibration DVD by example,
by setting the [Test Pattern] to Off.
Select the [Shift] adjustment and move the picture with the navigation buttons.
Left - Right shift 0% 5% 10% 15% 20% 25% 30% 34%
max. Up - Down shift 80% 74% 66% 57% 47% 34% 18% 0%
BACK
TEST
LIGHT
ASPECT
HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STANDBY
MENU
CINEMA
3
GAMMA C.TEMP
USER2 THX
LENS.
AP.
PIC.
ADJ.
PICTURE MODE
INPUT
CINEMA
1
CINEMA
2
NATURAL
STAGE
DYNAMIC
USER1
ON
LENS
BACK
TEST
LIGHT
ASPECT
HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STANDBY
MENU
CINEMA
3
USER2 THX
PICTURE MODE
INPUT
CINEMA
1
CINEMA
2
NATURAL
STAGE DYNAMIC
USER1
ON
LENS

2.0 INSTALLATION GUIDELINES
12 R599782 - Blackwing Four User Manual
Adjust the picture Focus
Into the [Lens Control] menu, press the [Ok] button to access the [Focus] adjustment. Use the up and down buttons
to adjust the picture focus.
Select the [Focus] adjustment and obtain a clear picture using [Up] and [Down] buttons.
Adjust the picture Zoom
Into the [Lens Control] menu, press the [Ok] button to access the [Zoom] adjustment. Use the up and down buttons
to adjust the picture size until the screen is completely filled.
Select the [Zoom] adjustment and resize the picture using [Up] and [Down] buttons.
BACK
TEST
LIGHT
ASPECT
HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STANDBY
MENU
CINEMA
3
USER2 THX
PICTURE MODE
INPUT
CINEMA
1CINEMA
2
NATURAL
STAGE DYNAMIC
USER1
ON
LENS
BACK
TEST
LIGHT
ASPECT
HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STANDBY
MENU
CINEMA
3
USER2 THX
PICTURE MODE
INPUT
CINEMA
1CINEMA
2
NATURAL
STAGE DYNAMIC
USER1
ON
LENS

3.0 REMOTE CONTROL UNIT (RCU)
R599782 - Blackwing Four User Manual 13
3.0 REMOTE CONTROL UNIT (RCU)
3.1 General view
3.2 Loading and replacing batteries
• Push the cover tab with the fingernail a little backwards and pull upwards the cover top.
Slide the cover forward to remove.
• Push the battery body towards the spring and lift up to remove.
Insert two AAA size batteries, making sure the polarities match the + and - marks inside the battery
compartment.
•Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until
it is firmly closed.
BACK
TEST
LIGHT
ASPECT
HIDE
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STAND BY
MENU
CINEMA
3
GAMMA
C.TEMP
USER2
LENS.
AP.
PIC.
ADJ.
PICTURE MODE
INPUT
CINEMA
1CINEMA
2
NATURAL
STAGE
DYNAMIC
USER1
ON [Power On] button
Select Active [Input]
Display [Menu]
[Stand By] button
[Aspect] Ratio
[Hide] Display
[Back] to previous menu
Navigation buttons
Backlight button
HDMI1, HDMI2,Component
Video, S-Video, PC
Lens Aperture
User1, User2, TH-PRO
Confirm button
[Lens] control:
Shift, Focus and Zoom
Display Test pattern
Gamma Adj.
Color temp. Adj.
Picture Control
Select Picture mode
Cinema1, Cinema2, Cinema3
Natural, Stage, Dynamic

3.0 REMOTE CONTROL UNIT (RCU)
14 R599782 - Blackwing Four User Manual
3.3 How to use the remote control unit
The operable distance of the remote control unit is about 7m for direct reception and within 30 degree angle with
respect to the sensor.
CAUTION WHEN USING BATTERIES
Do not mix new and old batteries.Do not mix different type of batteries as they are different in characteristics. Insert
batteries according to the + and - marks on the battery case. Do not put batteries into fire or recharge them if they
are not design to. Remove the batteries if the remote control is not to be used for a prolonged period. Use
manganese batteries wherever possible, Do not use rechargeable batteries.
NOTICE
If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out.
When this happens, replace the batteries. Insert the batteries according to the + and - marks.
The remote control unit can be used by having the transmission signal reflected off a screen, as the effect of
signals reflected from the RCU differ with the type of screen used, operable distance may decrease.
Front InfraRed sensor
Back InfraRed sensor

4.0 GETTING STARTED
R599782 - Blackwing Four User Manual 15
4.0 GETTING STARTED
4.1 General View
Front side
• Air Inlets: see “Air-Flow and Space Requirements”, page 8.
Rear side
• Operating LEDs: see section 4.3, page 17 for more details.
• Operating and Navigation buttons described in section 4.4, page 18.
• Lamp trap: see “Procedure for Lamp Replacement”, page 34 for more details about lamp replacement.
Input Panel side
• Main Power: connect the power cord as shown below.
• Input Panel: connect your video source to the correct input.
Air Inlet
Front IR sensor
Optical Lens
Back IR sensor
Operating LEDs Lamp trap
Operating buttons
Main Power
Input Panel

4.0 GETTING STARTED
16 R599782 - Blackwing Four User Manual
4.2 Connecting the Power Cord
•Before plugging in the Power Cord, ensure that all devices have been
connected.
•Connect the power cord to the power input terminal of the projector.
CAUTION AGAINST FIRE AND ELECTRIC SHOCK
Since the power consumption of this unit is high, insert the power plug directly into a wall outlet.
When not using devices, remove the power plug from the wall outlet.
Do not use power cords for connection other than specified.
Do not use a power voltage different from that which is indicated.
Do not cut, tear or modify the power cords. Also, do not place a heavy object on, heat or stretch the power cords as
this may cause damage to the cords.
Do not insert or pull plugs with a wet hand.

4.0 GETTING STARTED
R599782 - Blackwing Four User Manual 17
4.3 Operating LEDs
ID
Operating LED
Description
STANDBY/ON
(green or red)
LAMP
(orange)
WARNING
(red) Blinking
1 red - - - Unit is in standby mode
2 green - - - Unit is in operate mode (during projection)
3 blinking green - - Ye s
Unit is in operate mode, but HIDE is ON.
Press again on HIDE button to obtain a
picture.
4 blinking red - - Ye s Unit is in cooldown mode. (switching off)
5/6 - orange - -
Lamp time has reached 2900 hours,
prepare to replace the lamp before 3000
hours.
CAUTION
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets/exhaust vents by
standing the projector on its end or laying it on its side.
INPUT HIDE
MENU
BACK
OK
STANDBY/ON
(green/red LED)
LAMP
(orange LED)
WARNING
(red LED)

5.0 CONNECTIONS
18 R599782 - Blackwing Four User Manual
4.4 Operating and Navigation Buttons
5.0 CONNECTIONS
This unit can be connected to any compatible devices using the available inputs listed below:
• 2x HDMI revision 1.3 with HDCP
•1x Video
• 1x S-Video
• 1x Component (YPbPr / RGB / SCART)
• 1x 12 volt Trigger
• 1x RS-232
• 1x PC - VGA (sub D-15
The RS-232 terminal port can be used for automation.
For audio output, connect your audio video source to an amplifier.
This unit features a 12 Volt trigger output that can be used to control external device in On/Off mode or together with
an optional anamorphic lens systems.
Button Description
Hide display To temporary hide the picture.
Input source To switch input source.
Power button To turn On or Off the projector.
Up - down - left - right To navigate into On Screen Display (OSD) Menu.
OK (Enter) To select or to confirm action.
Back To return to previous menu or cancel action.
Menu To display On Screen Display (OSD) Menu.
INPUT HIDE
MENU
BACK
OK
Power button
Up - down
OK
Input source Back
Menu
Hide display
Left - right

5.0 CONNECTIONS
R599782 - Blackwing Four User Manual 19
5.1 Connecting a device to the projector
For input resolution and refresh rates, check the “PC compatible signals”, page 41.
Input Device
HDMI1, HDMI2 HDMI or DVI-D sources: Blu-Ray Disc player, DVD-player with HDMI, Game
Console, Computer with DVI-D output.
VGA Computer (VGA output), Multimedia box .
RS-232 (*) Automation Device, Control Device or Computer with RS-232*
S-Video DVD-Player, Game Console, digital camera, video camera
Video DVD-Player, Computer video, Game Console (SD), digital camera, video
camera.
YPbPr or RGB
or SCART (EU)
DVD-Player, HDTV Receiver, Game Console (SD or HD), DVB-T receiver,
Multimedia box, Analog Camera.
In order to use a SCART device* (Europe) on the Component input, you
must use cable sold separately and configure it into the projector menu.
Make sure to use a certified HDMI cable, especially when the distance between the different devices are
longer than 5 meters. If it is the case, the use of a split system or optical fiber cable is highly recommended.
(*) USING RS-232 WITH ACOMPUTER
The RS-232 Control and Automation may require specific software and tools. See “RS-232 input and IR Codes”,
page 37 for more details on RS-232 cabling and protocol.
YPbPr
Video
S-Video
RS-232
HDMI 2
HDMI 1
VGA (Sub D-15) or
RGB
or
SCART

5.0 CONNECTIONS
20 R599782 - Blackwing Four User Manual
5.2 Connecting a SCART device
5.3 Caution when connecting a device
CONNECTING ASCART DEVICE
This unit can be connected to a SCART device using a SCART to RGB+Sync cable. Once connected, select the
COMP. input as active input. Then browse into the projector menu to Input Signal > COMP. and select SCART
option.
CAUTION !
Prior to connecting any device to this unit, switch the projector in standby mode
Never connect a HDMI source to this unit when the projector is in operate mode. The HDMI termination is a self-
powered connection and can cause electric discharges.
SCART