Circutor Raption 150C Series User manual

Raption 150C Series
INSTALLATION GUIDE
(M358A01-03-22A)

Raption 150C
Installation guide2

Raption 150C
Installation guide 3
Revision log
Date Revision Description
04/22 M358A01-03-22A Initial Version
Disclaimer
CIRCUTOR, SA reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifica-
tions and the most updated manuals.
www.circutor.com

Raption 150C
Installation guide4
Raption 150C
Installation Guide
COPYRIGHT INFORMATION
This document is copyrighted, 2022 by CIRCUTOR, S.A. All rights are reserved. CIRCUTOR,
S.A. reserves the right to make improvements to the products described in this manual at
any time without notice.
No part of this manual can be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of the original manufacturer. Information
provided in this manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, or for any infringements upon the
rights of third parties that may result from its use.
All other product names or trademarks are properties of their respective owners.
CIRCUTOR reserves the right, in its discretion, to make any amendments, corrections or
changes to this manual and its contents at any time, without obligation to give prior notice.

Raption 150C
Installation guide 5
Here’s your guide to
install Raption 150C
Disclaimer ................................................................................................................................................ 3
Revision log ............................................................................................................................................. 3
Here’s your guide to install Raption 150C ......................................................................................... 5
1.-So, hello! ............................................................................................................................................. 6
2.-Before the installation ..................................................................................................................... 8
A.-Important safety instructions...................................................................................................... 8
B.-Electrical wiring considerations ................................................................................................. 9
C.-Important Electrical Safety instructions ................................................................................. 10
D.-EVSE Classification ...................................................................................................................... 11
E.-Storage .......................................................................................................................................... 12
F.-Unloading and handling ............................................................................................................. 13
3.-Dimensions and Overview ............................................................................................................. 14
A.-Dimensions ................................................................................................................................... 14
B.-Overview ....................................................................................................................................... 15
4.-Installation ........................................................................................................................................ 16
A.-Minimum distances .................................................................................................................... 16
B.-Foundation ................................................................................................................................... 17
C.-Opening ........................................................................................................................................ 23
D.-Placing .......................................................................................................................................... 25
E.-Wiring ............................................................................................................................................ 29
F.-Verification .................................................................................................................................... 34
G.-How to use and configure.......................................................................................................... 34
5.-Technical Data .................................................................................................................................. 36
Need help? ............................................................................................................................................ 39
Guarantee .............................................................................................................................................. 39

Raption 150C
Installation guide6
This manual provides information for installing the Charge Point, which has been designed
and tested to allow charging electric vehicles, as specified at IEC 61851 standards.
This document has different sections describing electrical components inside the Charge
Point and a step-by-step installation procedure.
It is mandatory to follow the basic security information supplied in this manual to ensure
safe and proper installation.
Failure to follow safety instructions may involve personal injury, equipment damage and
danger of death. CIRCUTOR is not responsible for events arising from such breach.
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENT
ELECTRIC RISK
-This symbol indicates a potentially hazardous situation which, if not avoided
may result in a risk of fire, serious injury or death.
- The Charge Point must be disconnected from any power source before
performing any maintenance, repair or electrical manipulation inside.
ATTENTION!
- Follow the instructions preceded by this symbol, if not respect them or
perform them correctly, may result in minor or moderate injury to the user,
damage to equipment, damage to facilities or other property.
- Handling the equipment can cause injuries as result of the dimension and
weight. Persons handling the unit must wear safety shoes and gloves.
1

Raption 150C
Installation guide 7
So, hello!
• Compliant with IEC 61851; Electric vehicle conductive charging system
(IEC 61851-1, IEC 61851-21-2 and IEC 61851-23).
• Compliant with IEC 62196, Plugs, sockets-outlets, vehicle connectors and
vehicles inlets, Conductive charging of electric vehicles (IEC 62196-1 and
IEC 62196-3).
• Compatible with CHAdeMO.
• Compliant with IEC 61851-24, Digital communication between a DC EV
charging station and an electric vehicle for control of DC charging.Meets
the CCS specification, DIN 70121. ISO 15118 ready.
• Directives: 2014/53/EU, Radio and Telecommunication Terminal
equipment; 2014/30/EU, Electromagnetic Compatibility (EMC);
2014/35/EU, Low Voltage directive.
• RFID complies with ISO 14443A/B/ MIFARE Classic/ DESFire EV1/ ISO
18092/ECMA-340/NFC 13.56MHz
• Meter complies with 2014/32/EU, Measuring Instruments Directive.
• Modem 4G complies with CE/RED.
• Compliant with RoHS 2011/65/EU-2017/2102, Restriction of Hazardous
Substances.

Raption 150C
Installation guide8
2
AImportant safety instructions
The Charge Point is designed for installation at indoor and outdoor areas. For each of the
different conditions of installation, the unit must be installed safely and ensure adequate
protection.
• Charge point must not be installed in
areas where there is potential risk of
explosion or any salinity level.
• Charge point must not be installed
in industrial areas with high level of
humidity or pollutants.
• Do not install the Charge Point where
falling objects may damage the
equipment.
• The surface where the Charge Point is
placed must withstand the mechanical
forces.
• Do not use this unit for anything other
than electric vehicle charging modes
expected in IEC 61851-1.
• Do not modify this unit. If modified,
CIRCUTOR will reject all responsibility and
the warranty will be void.
• Comply strictly with electrical safety
regulations according to your country.
• Do not make repairs or manipulations
with the unit energized.
• Only trained and qualified personnel
should have access to the electrical parts
inside the Charge Point.
• Check the installation annually by
qualified technician.
• Remove from service any item that has
a fault that could be dangerous for users
(broken plugs, caps that don’t close...).
• Use only CIRCUTOR supplied spare parts.
• Do not use this unit if the enclosure or the
EV connector is broken, cracked, open, or
shows any other indication of damage.
Read carefully all the instructions before starting in order
to ensure properly installation of the Charge Point.

Raption 150C
Installation guide 9
Before the installation
The input power supply line for the Charge Point must be hardwired from a dedicated
power transformer or generator and not by LV overhead power lines. It has to be done
under electrical safety regulations according to your country.
BElectrical wiring considerations
Take into consideration this section before start wiring
connections of the Charge Point.
1  INPUT POWER SUPPLY
The dimensioning of the input power supply line of the Charge Point must be checked
by a qualified electrician. Note that various factors, such as, cable length between
distribution board and the Charge Point; maximum input current of the Charge Point;
the installation way, may have influence of the selected cable. In such cases, increasing
the cable cross-section can be necessary. The installation company will be responsible
for dimensioning the wires cross section and the electrical protections, taking into
account the conditions above.
2  POWER SUPPLY LINE DIMENSIONING
Depending on the input power line, you can carry out the charging sessions
to the electric vehicle with different output power, it is possible to limit the
maximum output power by software so as not to exceed the available input power.
In order to implement this limitation by software, refer to the User Manual.
Note: In Chapter 4, you are going to find more electrical instructions so as to
implement a secure POWER SUPPLY LINE.
3  MAXIMUM OUTPUT POWER

Raption 150C
Installation guide10
Important Electrical Safety Instructions
C
A safe work environment is not enough to control all potential electrical hazards. It is
recommended to be very cautious and work safely. So, the safety rules shown below
could help to control risks of injury or death from workplace hazards.
• Avoid contact with energized
electrical circuits.
• Disconnect the power source
before servicing or repairing
electrical equipment.
• Use only tools and equipment with
non-conducting handles when
working on electrical devices.
• Never use metallic pencils or
rulers, or wear rings or metal
watchbands when working with
electrical equipment.
• Enclose all electric contacts and
conductors so that no one can
accidentally come into contact.
• When it is necessary to handle
equipment that is plugged in, be
sure hands are dry and, when
possible, wear nonconductive
gloves, protective clothes and
shoes with insulated soles.
• Never handle electrical equipment
when hands, feet, or body are wet
or perspiring, or when standing on
a wet floor.
Read carefully all the instructions before starting in order
to ensure properly handling of electrical parts.

Raption 150C
Installation guide 11
DEVSE Classification
Classification of the unit according to the IEC 61851-1:2017:
1 — Power supply Input • EV supply equipment connected to AC
supply network
• Permanently connected
2 — Power supply Output • DC EV supply equipment
3 — Environmental conditions • Indoor and outdoor
4 — Access • Equipment for locations with restricted
access and;
• Equipment for locations with non-
restricted access.
5 — Mounting method • Stationary equipment
- Ground mounted; floor mounted
6 — Protection against electric shock • Class I
7 — Charging models • Mode 4

Raption 150C
Installation guide12
Whenever possible, the Charge point must be unloaded in their place of installation and
operation. In case of unloaded to a temporary location for storage, it is convenient to not
remove the packaging and store them meeting the following minimum requirements:
• Safety: Charge Point must be protected against negative elements such as heat radiation,
direct solar radiation, mechanical damage, organic dissolvent impacts, etc.
• Temperature: for temperatures below -20 ºC and over +60º C special attention must be
paid to the storage and handling.
• Environment: Charge Point must be stored in a dry and dust-free location. The distance
from a heat source must be 1 m away. Outdoor storage of the unit has to be avoided.
EStorage
What’s included:
Charge Point
Installation
Manual
CirCarLife RFID
Mifare Card
Access
door Key
Foundation Kit
Eyebolts
Installation Guide

Raption 150C
Installation guide 13
All processes of unloading and handling of the Charge Point must be executed and monitored
by qualified personnel attending to the significant weight of the unit, complying with safety
rules and using the appropriate points of support.
Important notes:
• The delivery truck only unloads the pallet carrying the Charge Point.
• The delivery truck does not have the lifting facilities to move the Charge Point to its final
location.
• The placement of the Charge Point to its final location is the responsibility of the
contractor.
Once the Charge Point is already unloaded from the truck, move it to its final location with a
forklift.
FUnloading and handling

Raption 150C
Installation guide14
3
ADimensions
• Units specified in millimeters:
1140
1910
550
610
460
1290

Raption 150C
Installation guide 15
Dimensions and Overview
BOverview
1- Cover 2- CCS light beacon 3- CCS holder 4- CCS connector
5- Handle 6- RFID reader 7- Card payment 8- Touch screen
9- Air inlet Unit 10- CHAdeMO light beacon 11- CHAdeMO holder 12- CHAdeMO connector
13- Power M. air inlet 14- Decorative rear panel 15- 4G Antenna 16- Courtesy light
17- Exit cable 18- Emergency button 19- Decorative front panel
1
3
2
5
6
4
10
12
8
11
13
14
9
19
17
16
15
Note: Depending on the model, the components can vary.
7
18

Raption 150C
Installation guide16
4
AMinimum distances
When installing the Charge Point, respect the minimum distances for maintenance and safety
reasons.
Please comply accordingly to your country specifications.
The next picture shows how it should be installed.
• Do not install near areas where water or fluids can penetrate into the unit.
• Do not install the Charge Point on unstable terrain.
(1) Respect the minimum lateral distance to allow proper circulation of air flow. This unit has
forced ventilation.
(2) If Bollard Impact Protector is installed, keep 900 mm as a minimum distance in order to
give enough space to open the frontal door of the Charge Point for maintenance tasks.
1000 mm
(1)
50 mm
900 mm
(2)
1000 mm
(1)
Air inlet Air
outlet

Raption 150C
Installation guide 17
Installation
BFoundation
Foundation rod
435 mm x M16
24x
6x
1x
Nuts M16
Template upper part
The purpose of this chapter is the technical definition and basic requirements for implementing
the base and fixing the Charge Point.
• The unit is adequate for indoor and outdoor installation
• A foundation kit with a mounting template is provided to ensure the distances between
the foundation bolts.
Washers M16
6x
1x
Template lower part

Raption 150C
Installation guide18
TEMPLATE UPPER PART DIMENSIONS

Raption 150C
Installation guide 19
TEMPLATE LOWER PART DIMENSIONS

Raption 150C
Installation guide20
• Place the foundation bolts into the templates using provided nuts with the help of a
24mm open-end wrench. Take into consideration the following measures.
Step 1
Step 2