Circutor URBAN User manual

URBAN DC
INSTALLATION GUIDE
(M335A01-03-22A)

URBAN DC
2Installation Guide

URBAN DC
3
Installation Guide
Disclaimer
CIRCUTOR, SA reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifica-
tions and the most updated manuals.
www.circutor.com
Revision log
Date Revision Description
07/21 M335A01-03-21A Initial Version
11/21 M335A01-03-21B Changes in the following sections:
2.A.- 2.B.- 2.C.- 2.D.- 3.- 4.- 5.G.- 6.- 7.
02/22 M335A01-03-22A Changes in the following sections:
1.- 3.- 5.I.- 6.- 7.

URBAN DC
4Installation Guide
URBAN DC Manual
COPYRIGHT INFORMATION
This document is copyrighted, 2022 by CIRCUTOR, S.A. All rights are reserved. CIRCUTOR
S.A. reserves the right to make improvements to the products described in this manual
at any time without notice.
No part of this manual can be reproduced, copied, translated or transmitted in any form
or by any means without the prior written permission of the original manufacturer.
Information provided in this manual is intended to be accurate and reliable. However,
the original manufacturer assumes no responsibility for its use, or for any infringements
upon the rights of third parties that may result from its use.
All other product names or trademarks are properties of their respective owners.
CIRCUTOR reserves the right, in its discretion, to make any amendments, corrections
or changes to this manual and its contents at any time, without obligation to give prior
notice.

URBAN DC
5
Installation Guide
Here’s your guide to
install URBAN DC
Disclaimer .................................................................................................................................................3
Revision log...............................................................................................................................................3
Here’s your guide to install URBAN DC .............................................................................................5
1.-So, hello ................................................................................................................................................6
2.-Before installation...............................................................................................................................8
A. Important Safety Instructions ...................................................................................................8
B. Electrical wiring considerations................................................................................................9
C. Important Electrical Safety Instructions................................................................................10
D. EVSE Classification ....................................................................................................................11
3.- Oveview...............................................................................................................................................12
4.- Dimensions........................................................................................................................................14
5.-. Installation........................................................................................................................................16
A. Space requirements.....................................................................................................................17
B. Foundation ....................................................................................................................................18
C. Opening .........................................................................................................................................19
D. Positioning ....................................................................................................................................20
E. Fixation...........................................................................................................................................21
F. Metal plate .....................................................................................................................................21
G. Wiring ............................................................................................................................................22
H. Verification ...................................................................................................................................23
I. How to use and configure MASTER and SATELLITE URBAN DC ..........................................24
6.-. How to use URBAN DC BASIC ......................................................................................................26
A.Standby...........................................................................................................................................26
B. Start charging...............................................................................................................................26
C. Charging.........................................................................................................................................26
D. Charged..........................................................................................................................................27
E Stop charging.................................................................................................................................27
F. Error ...............................................................................................................................................27
7. Technical data .................................................................................................................................. 28
Need help?..............................................................................................................................................31
Guarantee................................................................................................................................................31

URBAN DC
6Installation Guide
1

URBAN DC
7
Installation Guide
This manual provides commissioning and use instructions information about URBAN
DC, which has been designed and tested to allow electric vehicle charging, specified
in IEC 61851.
This document has different sections such as step-by-step installation procedure
and technical data.
ELECTRIC RISK
Take precautions to make the electrical connection inside the unit. Unit
must be disconnected from any power source during commissioning.
ATTENTION!
Indicates that the damage to property can occur if appropiate
precautions are not taken.
So, hello!
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENT
• Compliant with IEC 61851; Electric vehicle conductive charging system (IEC 61851-1 and
IEC 61851-23).
• Compliant with IEC 62196; Plugs, sockets-outlets,vehicle connectors and vehicle inlets-
Conductive charging of electric vehicles (IEC 62196-1, IEC 62196-2 and IEC 62196-3).
• Directives: 2014/53/UE, Radio and Telecommunication Terminal equipment; 2014/30/
UE, Electromagnetic Compatibility (EMC); 2014/35/UE, Low Voltage.
• Compliant with IEC 61851-24, Digital communication between a DC EV charging station
and an electric vehicle for control of DC charging. Meets the CCS specification, DIN
SPEC 70121. ISO 15118 ready.
• Compliant with RoHS 2011/65/EU-2017/2102, Restriction of Hazardous Substances.
• RFID complies with ISO 14443A/B, Identification cards- Contactless integrated circuit
cards- Proximity cards.
• Modem 4G complies with CE/RED

URBAN DC
8Installation Guide
Important Safety Instructions
2
Refer toTECHNICAL DATA section for more information about environmental installation conditions.
The Charge Point is designed for installation at indoor and outdoor areas. For each of the
different conditions of installation, the unit must be installed safely and ensure adequate
protection.
• Charge Point must not be installed in
areas where there is potential risk of
explosion or any salinity level.
• Charge Point must not be installed
in industrial areas with high level of
humidity or pollutants.
• Do not install the Charge Point where
falling objects may damage the
equipment.
• The surface where the Charge
Point is placed must withstand the
mechanical forces.
• Do not use this unit for anything
other than electric vehicle charging
modes are expected in IEC 61851.
• Do not modify this unit. If modified,
CIRCUTOR will reject all responsibility
and the warranty will be void.
• Comply strictly with electrical safety
regulations according to your country.
• Do not make repairs or manipulations
with the unit energized.
• Only trained and qualified personnel
should have access to the electrical
parts inside the Charge Point.
• Check the installation annually by
qualified technician.
• Remove from service any item
that has a fault that could be
dangerous for users (broken
plugs, caps that don’t close...).
• Use only CIRCUTOR supplied spare
parts.
• Do not use this unit if the enclosure
or the EV connector is broken,
cracked, open, or shows any
Read carefully all the instructions before starting in order
to ensure properly installation of the Charge Point.
A

URBAN DC
9
Installation Guide
Electrical wiring considerations
Take into consideration this section before start wiring
connections of the Charge Point.
Before installation
1  ELECTRICAL PROTECTIONS
Charge Point may not include elements of electrical protection.
If this equipment has internal electrical protections, are installed in each socket-outlet
for the protection of the user against an electrical failure, according to the international
standard IEC 61851-1:2017.
In order to guarantee the total protection of the users and the installation (power supply line
included) in front of any electrical hazard, it is mandatory to install a main circuit breaker
(MCB) and a residual current device (RCD) upstream of the Charge Point.
These electrical protections and the rest of the installation have to be aligned with the local
and national rules. The selectivity of the protections has to be guaranteed at all times.
2  POWER SUPPLY LINE DIMENSIONING
The dimensioning of the input power supply line of the Charge Point must be checked by
a qualified electrician. Note that various factors such as cable length between distribution
board and Charge Point, maximum output current of the Charge Point may have influence
of the selected cable.
In such cases, increasing the cable cross-section it is required to adapt the temperature
resistance of the power supply line.
3  MAXIMUM OUTPUT CURRENT
Please refer to the TECHNICAL DATA section to consult the default factory settings from
maximum output current of the Charge Point.
Depending on the model this value may vary.
B

URBAN DC
10 Installation Guide
• Avoid contact with energized
electrical circuits.
• Disconnect the power source
before servicing or repairing
electrical equipment.
• Use only tools and equipment with
non-conducting handles when
working on electrical devices.
• Never use metallic pencils or
rulers, or wear rings or metal
watchbands when working with
electrical equipment.
• Enclose all electric contacts and
conductors so that no one can
accidentally come into contact.
• When it is necessary to handle
equipment that is plugged in, be
sure hands are dry and, when
possible, wear nonconductive
gloves, protective clothes and
shoes with insulated soles.
• Never handle electrical equipment
when hands, feet, or body are wet
or perspiring, or when standing on
a wet floor.
Important Electrical Safety Instructions
Read carefully all the instructions before starting in
order to ensure properly handling of electrical parts.
A safe work environment is not enough to control all potential electrical hazards. It is
recommended to be very cautious and work safely. So, the safety rules shown below
could help to control risks of injury or death from workplace hazards.
C

URBAN DC
11
Installation Guide
DEVSE Classification
Classification of the unit according to the IEC 61851-1:2017:
1 — Power supply Input
• EV supply equipment connected to
AC supply network
• Permanently connected
2 — Power supply Output • DC EV supply equipment
3 — Environmental conditions • Indoor and outdoor
4 — Access
• Equipment for locations with restrict-
ed access and;
• Equipment for locations with non-re-
stricted access.
5 — Mounting method
• Stationary equipment
- Ground mounted; floor mounted
6 — Protection against electric shock • Class I
7 — Charging modes • Mode 4

URBAN DC
12 Installation Guide
3
What’s included:
Charge Point Installation &
User Manual
Foundation
Kit
Electric
cabinet key +
security key
+
Installation guide
CirCarLife RFID
Mifare Card(1)
(1) Depending on the model chosen, the elements included in the package can vary.

URBAN DC
13
Installation Guide
Overview
1
4
5
3
2
1.- Hat
2.-LED beacon light
3.-Holder
4.-Cable
5.-Key lock access
6.-Ventilation
7.-Base
8.-START button
9.-STOP button
10.-Cable roller
11.-Cable gland
12.- Screen
13.- RFID reader
14.- Credir card payment (2)
6
7
9
5
5
6
11
10
1 1
22
66
55
33
12
10 10
5
5 5
5
11 11
66
77
8
13 14
URBAN DC BASIC URBAN DC MASTERURBAN DC SATELLITE
(2) Depending on the model, the components can vary.

URBAN DC
14 Installation Guide
4

URBAN DC
15
Installation Guide
Dimensions
446
234
1750
80
281
Measures in mm
479
Charge point:
288 438
1064
1198

URBAN DC
16 Installation Guide
5
What is needed:
Nuts
DIN 934 M16
Washers
DIN 9021 M16
Templates
Foundation bolts
16x
2x
4x
4x

URBAN DC
17
Installation Guide
Installation
ASpace requirements
100
500 500
x(3)
Measures in mm
When installing the unit, respect the minimum distances for maintenance and safety reasons.
Please comply accordingly to your country specifications.
The next picture shows how it should be installed.
• Do not install near areas where water or fluids can penetrate into the unit.
• Do not install the unit on unstable terrain.
(3) X If Bollard Impact Protector is installed, keep 500 mm as a minimum distance in order to
give enough space to open the frontal door of the Charge Point for maintenance tasks.

URBAN DC
18 Installation Guide
BFoundation
450
250
119
230
320
300
Measures in mm
• Place the foundation bolts into
the template using the provided
nuts with the help of a 24mm
open-end wrench.
• Once the kit is assembled, it must
be placed in the ground taking
into consideration the following
measures.
Note: If there is any further doubt about the terrain regarding the installation of this unit,
due to the weight and dimensions, it will be necessary to define a final solution to install the
unit. It shall be performed an specific technical project made by an architectural firm prior
to its installation.
220
130
500 300
Front view Side view
400

URBAN DC
19
Installation Guide
C
1 2
Opening
1.- Introduce provided URBAN DC key in the lock located at the mid part
of the unit and the security key at the top and bottom locks of the unit.
Then, the unit is unlocked and ready to be opened.
2. - Pull outward the Tamper switch(4) to operate the Charge Point.
(4) Tamper Switch: The Charge Point has a security switch (antitamper protection) installed
that will avoid any charging session if the doors are opened.
It has three positions.
1.- Operative postition: The Charge Point is closed.
2.- Error position: The Charge Point is opened without supervision.
3.- Mantenance position: The Charge Point is opened under maintenance (Pulling otward
the tamper switch).

URBAN DC
20 Installation Guide
DPositioning
1.- Remove the template nuts before proceeding.
2.- Place the Charge Point through the four foundation bolts. Make sure that the Charge Point
pre-holes of the metal plate match with the cable glands.
URBAN DC can be placed at outdoor or indoor areas to charge electric vehicles. This product
series is designed to be placed on the ground.