Cisco GS7000 Operator's manual

OL-29937-01
Model GS7000 Hub/Node Status
Monitor/Local Control Module
Installation and Configuration Guide

For Your Safety
Explanation of Warning and Caution Icons
Avoid personal injury and product damage! Do not proceed beyond any symbol
until you fully understand the indicated conditions.
The following warning and caution icons alert you to important information about
the safe operation of this product:
You may find this symbol in the document that accompanies this product.
This symbol indicates important operating or maintenance instructions.
You may find this symbol affixed to the product. This symbol indicates a live
terminal where a dangerous voltage may be present; the tip of the flash points
to the terminal device.
You may find this symbol affixed to the product. This symbol indicates a
protective ground terminal.
You may find this symbol affixed to the product. This symbol indicates a
chassis terminal (normally used for equipotential bonding).
You may find this symbol affixed to the product. This symbol warns of a
potentially hot surface.
You may find this symbol affixed to the product and in this document. This
symbol indicates an infrared laser that transmits intensity-modulated light
and emits invisible laser radiation or an LED that transmits intensity-
modulated light.
Important
Please read this entire guide. If this guide provides installation or operation
instructions, give particular attention to all safety statements included in this guide.

Notices
Trademark Acknowledgments
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its
affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks.
Third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between
Cisco and any other company. (1110R)
Publication Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may
appear in this publication. We reserve the right to change this publication at any
time without notice. This document is not to be construed as conferring by
implication, estoppel, or otherwise any license or right under any copyright or
patent, whether or not the use of any information in this document employs an
invention claimed in any existing or later issued patent.
Copyright
© 2009-2010, 2013 Cisco and/or its affiliates. All rights reserved.
Information in this publication is subject to change without notice. No part of this
publication may be reproduced or transmitted in any form, by photocopy,
microfilm, xerography, or any other means, or incorporated into any information
retrieval system, electronic or mechanical, for any purpose, without the express
permission of Cisco Systems, Inc.

OL-29937-01 iii
Contents
Important Safety Instructions v
Chapter 1 Overview 1
Model GS7000 Hub/Node Description ................................................................................ 2
Overview...................................................................................................................... 2
Physical Description ................................................................................................... 2
Functional Description............................................................................................... 5
Status Monitor/Local Control Module Description ...........................................................8
Overview...................................................................................................................... 8
Status Monitor Description ....................................................................................... 8
Local Control Module Description........................................................................... 9
Chapter 2 Installation 11
Installing the SM/LCM......................................................................................................... 12
Overview.................................................................................................................... 12
Opening the Housing............................................................................................... 12
Installing the Module ............................................................................................... 12
Closing the Housing................................................................................................. 17
Node Power Limitations.......................................................................................... 17
Chapter 3 Configuration 19
Local Control Module Configuration Procedure .............................................................. 20
Introduction............................................................................................................... 20
Configuring the LCM...............................................................................................20
Status Monitor Configuration Procedure........................................................................... 27
Introduction............................................................................................................... 27
SM Configuration Parameters................................................................................. 27
Configuring the SM .................................................................................................. 29
Application Software Remote Download and Upgrade ..................................... 30
Chapter 4 Management Via SNMP 33
Introduction............................................................................................................................ 34
MIBs Used in the Optical Hub/Node................................................................................. 35
MIB-2 Specifications .............................................................................................................. 36
MIB-2 System MIB .................................................................................................... 36
MIB-2 Entity MIB ...................................................................................................... 36

Contents
iv OL-29937-01
Cisco Proprietary MIB Specifications.................................................................................. 39
Optical Transmitter Table........................................................................................ 39
Optical Receiver Table.............................................................................................. 40
saFnForwardConfig.................................................................................................. 40
Redundancy Control Table...................................................................................... 42
Power Supply Table.................................................................................................. 42
HMS MIB Specifications ....................................................................................................... 43
SCTE-HMS-PROPERTY-MIB.................................................................................. 43
SCTE-HMS-ALARMS-MIB...................................................................................... 45
SCTE-HMS-COMMON-MIB................................................................................... 46
SCTE-HMS-FIBERNODE-MIB................................................................................ 46
SCTE-HMS-DOWNLOAD-MIB ............................................................................. 47
SCTE-HMS-HE-COMMON-MIB............................................................................ 50
SCTE-HMS-HE-OPTICAL-AMPLIFIER-MIB....................................................... 50
SCTE-HMS-HE-OPTICAL-SWITCH-MIB............................................................. 52
Chapter 5 Troubleshooting 55
SM/LCM Sensors and Indicators........................................................................................ 56
Local Control Module Troubleshooting ............................................................................. 57
Introduction............................................................................................................... 57
Green STATUS LED not Blinking........................................................................... 57
Red FAULT LED Blinking Slowly.......................................................................... 57
Red FAULT LED Flashing Fast...............................................................................59
Red FAULT LED On Solid....................................................................................... 59
Status Monitor Troubleshooting.......................................................................................... 60
Introduction............................................................................................................... 60
SM Transponder Module Indicators ...................................................................... 60
No Frequency Found State ...................................................................................... 61
Ch Description (Channel Description) State......................................................... 61
Registered State......................................................................................................... 62
Error State .................................................................................................................. 63
Chapter 6 Customer Information 65
Glossary 67
Index 75

Important Safety Instructions
OL-29937-01 v
Important Safety Instructions
Read these instructions. Keep these instructions. Heed all warnings. Follow all
instructions. Only use attachments/accessories specified by the manufacturer.
Read and Retain Instructions
Carefully read all safety and operating instructions before operating this equipment,
and retain them for future reference.
Follow Instructions and Heed Warnings
Follow all operating and use instructions. Pay attention to all warnings and cautions
in the operating instructions, as well as those that are affixed to this equipment.
Terminology
The terms defined below are used in this document. The definitions given are based
on those found in safety standards.
Service Personnel - The term service personnel applies to trained and qualified
individuals who are allowed to install, replace, or service electrical equipment. The
service personnel are expected to use their experience and technical skills to avoid
possible injury to themselves and others due to hazards that exist in service and
restricted access areas.
User and Operator - The terms user and operator apply to persons other than service
personnel.
Ground(ing) and Earth(ing) - The terms ground(ing) and earth(ing) are synonymous.
This document uses ground(ing) for clarity, but it can be interpreted as having the
same meaning as earth(ing).
Electric Shock Hazard
This equipment meets applicable safety standards.
WARNING:
To reduce risk of electric shock, perform only the instructions that are
included in the operating instructions. Refer all servicing to qualified service
personnel only.
Electric shock can cause personal injury or even death. Avoid direct contact with
dangerous voltages at all times.

Important Safety Instructions
vi OL-29937-01
Know the following safety warnings and guidelines:
Only qualified service personnel are allowed to perform equipment installation
or replacement.
Only qualified service personnel are allowed to remove chassis covers and access
any of the components inside the chassis.
Equipment Placement
WARNING:
Avoid personal injury and damage to this equipment. An unstable mounting
surface may cause this equipment to fall.
To protect against equipment damage or injury to personnel, comply with the
following:
Install this equipment in a restricted access location (access restricted to service
personnel).
Make sure the mounting surface or rack is stable and can support the size and
weight of this equipment.
Strand (Aerial) Installation
CAUTION:
Be aware of the size and weight of strand-mounted equipment during the
installation operation.
Ensure that the strand can safely support the equipment’s weight.
Pedestal, Service Closet, Equipment Room or Underground Vault Installation
WARNING:
Avoid the possibility of personal injury. Ensure proper handling/lifting
techniques are employed when working in confined spaces with heavy
equipment.
Ensure this equipment is securely fastened to the mounting surface or rack
where necessary to protect against damage due to any disturbance and
subsequent fall.
Ensure the mounting surface or rack is appropriately anchored according to
manufacturer’s specifications.
Ensure the installation site meets the ventilation requirements given in the
equipment’s data sheet to avoid the possibility of equipment overheating.

Important Safety Instructions
OL-29937-01 vii
Ensure the installation site and operating environment is compatible with the
equipment’s International Protection (IP) rating specified in the equipment’s data
sheet.
Connecting to Utility AC Power
Important: If this equipment is a Class I equipment, it must be grounded.
If this equipment plugs into an outlet, the outlet must be near this equipment,
and must be easily accessible.
Connect this equipment only to the power sources that are identified on the
equipment-rating label, which is normally located close to the power inlet
connector(s).
This equipment may have two power sources. Be sure to disconnect all power
sources before working on this equipment.
If this equipment does not have a main power switch, the power cord connector
serves as the disconnect device.
Always pull on the plug or the connector to disconnect a cable. Never pull on the
cable itself.
Connection to Network Power Sources
Refer to this equipment’s specific installation instructions in this manual or in
companion manuals in this series for connection to network ferro-resonant AC
power sources.
AC Power Shunts
AC power shunts may be provided with this equipment.
Important: The power shunts (where provided) must be removed before installing
modules into a powered housing. With the shunts removed, power surge to the
components and RF-connectors is reduced.
CAUTION:
RF connectors and housing seizure assemblies can be damaged if shunts are
not removed from the equipment before installing or removing modules from
the housing.
Grounding (Utility AC Powered Equipment in Pedestals, Service Closets, etc.)
This section provides instructions for verifying that the equipment is properly
grounded.

Important Safety Instructions
viii OL-29937-01
Safety Plugs (USA Only)
This equipment may be equipped with either a 3-terminal (grounding-type) safety
plug or a 2-terminal (polarized) safety plug. The wide blade or the third terminal is
provided for safety. Do not defeat the safety purpose of the grounding-type or
polarized safety plug.
To properly ground this equipment, follow these safety guidelines:
Grounding-Type Plug - For a 3-terminal plug (one terminal on this plug is a
protective grounding pin), insert the plug into a grounded mains, 3-terminal
outlet.
Note: This plug fits only one way. If this plug cannot be fully inserted into the
outlet, contact an electrician to replace the obsolete 3-terminal outlet.
Polarized Plug - For a 2-terminal plug (a polarized plug with one wide blade
and one narrow blade), insert the plug into a polarized mains, 2-terminal outlet
in which one socket is wider than the other.
Note: If this plug cannot be fully inserted into the outlet, try reversing the plug.
If the plug still fails to fit, contact an electrician to replace the obsolete 2-terminal
outlet.
Grounding Terminal
If this equipment is equipped with an external grounding terminal, attach one end of
an 18-gauge wire (or larger) to the grounding terminal; then, attach the other end of
the wire to a ground, such as a grounded equipment rack.
Safety Plugs (European Union)
Class I Mains Powered Equipment –Provided with a 3-terminal AC inlet and
requires connection to a 3-terminal mains supply outlet via a 3-terminal power
cord for proper connection to the protective ground.
Note: The equipotential bonding terminal provided on some equipment is not
designed to function as a protective ground connection.
Class II Mains Powered Equipment –Provided with a 2-terminal AC inlet that
may be connected by a 2-terminal power cord to the mains supply outlet. No
connection to the protective ground is required as this class of equipment is
provided with double or reinforced and/or supplementary insulation in
addition to the basic insulation provided in Class I equipment.
Note: Class II equipment, which is subject to EN 50083-1, is provided with a
chassis mounted equipotential bonding terminal. See the section titled
Equipotential Bonding for connection instructions.