Cisco Catalyst CG113-4GW6 Manual

Hardware Installation Guide for Cisco Catalyst Wireless Gateways
First Published: 2023-01-16
Last Modified: 2023-08-17
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1721R)
©2023 Cisco Systems, Inc. All rights reserved.

CONTENTS
Full Cisco Trademarks with Software License ?
Overview 1
CHAPTER 1
Cisco Catalyst Wireless Gateway CG113-W6 2
Package Contents 2
Hardware Specifications 2
Ethernet Interfaces, Power Port, and Reset Button 3
LED Indicators 4
Antenna Information 6
Power Supply 6
Cisco Catalyst Wireless Gateway CG113-4GW6 7
Package Contents 7
Hardware Specifications 7
Ethernet Interfaces and Power Port 8
SIM Card Slots 9
LED Indicators 10
Antenna Information 12
Power Supply 13
Safety Guidelines and Warnings 15
CHAPTER 2
Statement 1071—Warning Definition 15
Statement 407—Japanese Safety Instruction 16
Statement 1004—Installation Instructions 16
Statement 1033—Safety Extra-Low Voltage (SELV)—IEC 60950/ES1–IEC 62368 DC Power
Supply 16
Statement 1047—Overheating Prevention 16
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
iii

Statement 1074—Comply with Local and National Electrical Codes 17
Install Cisco Catalyst Wireless Gateways 19
CHAPTER 3
Device Placement 19
Install SIMs, LTE Models 20
Power 21
Data Connections 21
Connect Devices 23
CHAPTER 4
Declarations of Conformity and Regulatory Information 25
APPENDIX A
USA Conformity and Regulatory Information 25
Manufacturers Federal Communication Commission Declaration of Conformity Statement 25
Canada Conformity and Regulatory Information 27
Canada Compliance Statement 27
European Community and UK Conformity and Regulatory Information 28
European Community, Switzerland, Norway, Iceland, and Liechtenstein Compliance 28
United Kingdom Compliance 29
RF Exposure, Additional Information 30
Generic Discussion on RF Exposure 30
Additional Information on RF Exposure 30
Additional References 33
APPENDIX B
Additional References 33
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
iv
Contents

CHAPTER 1
Overview
Cisco Catalyst Wireless Gateways extend an enterprise network to remote workers, providing numerous
advantages:
• Hardware-based stable connectivity to an enterprise VPN
• Optimized network performance with Wi-Fi 6
• Cellular network connectivity, in supporting models, providing a cellular internet connection (with one
active and one standby SIM) for uninterrupted internet connectivity
• Separate service set identifiers (SSIDs) for connecting work and personal devices
Cisco Catalyst Wireless Gateway connectivity is as follows:
• The Cisco Catalyst Wireless Gateway CG113-W6 accesses the internet using a wired WAN connection
at a remote site.
•The Cisco Catalyst Wireless Gateway CG113-4GW6 accesses the internet using a wired WAN connection
at a remote site or using a cellular link. The device supports two SIM cards: one active, and one on
standby. If the wired WAN connection fails, the device fails over to the cellular link to ensure internet
connectivity.
The device has a single cellular connection, so only one SIM can be active at a given time. You can configure
which of the two SIM slots serves as primary and which serves as secondary (failover).
Note
Managing Cisco Catalyst Wireless Gateways
Use Cisco SD-WAN Manager to configure and manage Cisco Catalyst Wireless Gateways. Cisco SD-WAN
Manager provides a convenient workflow for configuring Wi-Fi, cellular, VPN, and other functionality. Cisco
SD-WAN Manager also provides methods for monitoring device performance.
•Cisco Catalyst Wireless Gateway CG113-W6, on page 2
•Cisco Catalyst Wireless Gateway CG113-4GW6, on page 7
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
1

Cisco Catalyst Wireless Gateway CG113-W6
The following sections provide hardware specifications and other information about the Cisco Catalyst Wireless
Gateway CG113-W6.
Package Contents
The package for this device contains the following:
• Device chassis
• Power supply
• Pointer card, providing a link to the product documentation
Hardware Specifications
Table 1: Hardware Specifications, Cisco Catalyst Wireless Gateway CG113-W6
SpecificationsItem
Interfaces
1
2.5 Gigabit ethernet
21 Gigabit ethernet
Wi-Fi
2.4 GHz, 5 GHz
Wi-Fi bands
Dual 2x2 MIMO (internal)Antennas
Cellular
None
Operating Conditions
0℃ to 45℃ (32℉ to 113℉)
Temperature
10 to 90% RH Non-condensingHumidity
3000 m (10,000 ft)Altitude
Storage Conditions
-25℃ to 70℃ (-13℉ to 158℉)
Temperature
5 to 95% RH Non-condensingHumidity
4570 m (15,000 ft)Altitude
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
2
Overview
Cisco Catalyst Wireless Gateway CG113-W6

SpecificationsItem
Power
12V, 3A maximum
Models, according to region: CG113-4G-PWR-US, -EU, -AU
Power adapter
USB-CPower connector
Mounting and Accessories
The device is installed on a desk or other flat surface. No additional mounting equipment is supplied.
Ethernet Interfaces, Power Port, and Reset Button
The ethernet interfaces, power port, and reset button are located on the back panel of the device.
Figure 1: Back Panel
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
3
Overview
Ethernet Interfaces, Power Port, and Reset Button

Figure 2: Reset Button, Interfaces, and Power Port
Reset button1
1 Gbps ethernet interfaces2
2.5 Gbps ethernet interface3
USB-C power port4
LED Indicators
The single LED indicator appears on the front panel of the device.
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
4
Overview
LED Indicators

Figure 3: Front Panel
Figure 4: LED Indicator on Front Panel
LED indicator for Wi-Fi connectivity1
Table 2: LED Indicator Behavior
DescriptionColorLED
Device is bootingRed, blinkingWi-Fi
Wi-Fi not readyRed, solid
Wi-Fi ready, no devices connectedGreen, solid
Wi-Fi ready, one or more devices connectedBlue, solid
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
5
Overview
LED Indicators

Antenna Information
Antennas, Gain, and Impedance
Table 3: List of Internal Antennas Supported on Cisco CG113-W6
Antenna ImpedanceAntenna GainAntenna Type
50 ohms2.4GHz: 4dBi
5GHz: 5dBi
Antenna type: Wi-Fi
Single-Port/Dual Band/Omni-directional
(Linear Polarization, Wi-Fi 1)
50 ohms2.4GHz: 2.6dBi
5GHz: 4.8dBi
Antenna type: Wi-Fi
Single-Port/Dual Band/Omni-directional
(Linear Polarization, Wi-Fi 2)
Maximum Transmitted Power
The frequency and the maximum transmitted power are listed below:
2412-2472MHz: 19.99 dBm
5180-5240MHz: 22.92 dBm
5260-5320MHz: 22.95 dBm
5500-5700: 29.97 dBm
Power Supply
The following power supplies are included with the device, depending on region.
Table 4: Power Supply Part and Model Numbers, by Region
Model NumberCisco Part NumberRegion
ADH-36DW BCG113-4G-PWR-USUSA
ADH-36DW ECG113-4G-PWR-AUAustralia
ADH-36DW CCG113-4G-PWR-EUEU, UK
Table 5: Power Supply Specifications
DescriptionSpecification
100-240V AC 50-60HzInput
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
6
Overview
Antenna Information

Cisco Catalyst Wireless Gateway CG113-4GW6
The following sections provide hardware specifications and other information about the Cisco Catalyst Wireless
Gateway CG113-4GW6.
Package Contents
The package for this device contains the following:
• Device chassis
• Power supply
• Pointer card, providing a link to the product documentation
Hardware Specifications
Table 6: Hardware Specifications, Cisco Catalyst Wireless Gateway CG113-4GW6
SpecificationsItem
Interfaces
1
2.5 Gigabit ethernet
21 Gigabit ethernet
Wi-Fi
2.4 GHz, 5 GHz
Wi-Fi bands
Dual 2x2 MIMO (internal)Antennas
Cellular
2
SIM slots
4G/Cat7Cellular bands
Operating Conditions
0℃ to 45℃ (32℉ to 113℉)
Temperature
10 to 90% RH Non-condensingHumidity
3000 m (10,000 ft)Altitude
Storage Conditions
-25℃ to 70℃ (-13℉ to 158℉)
Temperature
5 to 95% RH Non-condensingHumidity
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
7
Overview
Cisco Catalyst Wireless Gateway CG113-4GW6

SpecificationsItem
4570 m (15,000 ft)Altitude
Power
12V, 3A maximum
Models, according to region: CG113-4G-PWR-US, -EU, -AU
Power adapter
USB-CPower connector
Mounting and Accessories
The device is installed on a desk or other flat surface. No additional mounting equipment is supplied.
Ethernet Interfaces and Power Port
The ethernet interfaces, power port, and reset button are located on the back panel of the device.
Figure 5: Back Panel
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
8
Overview
Ethernet Interfaces and Power Port

Figure 6: Reset Button, Interfaces, and Power Port
Reset button1
1 Gbps ethernet interfaces2
2.5 Gbps ethernet interface3
USB-C power port4
SIM Card Slots
The SIM card slots are accessible from the bottom panel of the device. For information about installing SIM
cards, see Install SIMs, LTE Models, on page 20.
Figure 7: Bottom Panel
Cover for SIM card slots1
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
9
Overview
SIM Card Slots

Figure 8: SIM Card Slots, with the Cover Removed
SIM card slots 0 and 11
Figure 9: SIM Card Slots
LED Indicators
The LED indicators appear on the front panel of the device.
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
10
Overview
LED Indicators

Figure 10: Front Panel
Figure 11: LED Indicators on Front Panel
LED indicator for cellular connectivity1
LED indicator for Wi-Fi connectivity2
Table 7: LED Indicator Behavior
DescriptionColorLED
Device is bootingRed, blinkingWi-Fi
Wi-Fi not readyRed, solid
Wi-Fi ready, no devices connectedGreen, solid
Wi-Fi ready, one or more devices connectedBlue, solid
Firmware upgrade in progressGreen, blinking
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
11
Overview
LED Indicators

DescriptionColorLED
Device is booting
Red, blinking4G
Completed boot, no SIM detected, not connected to
network
Red, solid
SIM detected, connected to network, wired connection
is active and cellular connection is standby
Green, solid
Firmware upgrade in progressGreen, blinking
SIM detected, connected to network, cellular
connection is active, weak signal
Blue, blinking
SIM detected, connected to network, cellular
connection is active, strong signal
Blue, solid
Antenna Information
Antennas, Gain, and Impedance
Table 8: List of Internal Antennas Supported on Cisco CG113-4GW6 (Includes LTE)
Antenna ImpedanceAntenna GainAntenna Type
50 ohms2.4GHz: 4dBi
5GHz: 5dBi
Antenna type: Wi-Fi
Single-Port/Dual Band/Omni-directional
(Linear Polarization, Wi-Fi 1)
50 ohms2.4GHz: 2.6dBi
5GHz: 4.8dBi
Antenna type: Wi-Fi
Single-Port/Dual Band/Omni-directional
(Linear Polarization, Wi-Fi 2)
50 ohms617-960MHz: 2.1dBi
1710-2700MHz: 4.1dBi
3300-3800MHz: 3.6dBi
Antenna type: LTE
Single-Port/LTE Full Band/Omni-directional
(Mixed Polarization, LTE Main)
50 ohms617-960MHz: 2.1dBi
1710-2700MHz: 4.1dBi
3300-3800MHz: 3.6dBi
Antenna type: LTE
Single-Port/LTE Full Band/Omni-directional
(Vertical Polarization, LTE Auxiliary)
Maximum Transmitted Power
The frequency and the maximum transmitted power are listed below:
2412-2472MHz: 19.99 dBm
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
12
Overview
Antenna Information

5180-5240MHz: 22.92 dBm
5260-5320MHz: 22.95 dBm
5500-5700: 29.97 dBm
Power Supply
The following power supplies are included with the device, depending on region.
Table 9: Power Supply Part and Model Numbers, by Region
Model NumberCisco Part NumberRegion
ADH-36DW BCG113-4G-PWR-USUSA
ADH-36DW ECG113-4G-PWR-AUAustralia
ADH-36DW CCG113-4G-PWR-EUEU, UK
Table 10: Power Supply Specifications
DescriptionSpecification
100-240V AC 50-60HzInput
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
13
Overview
Power Supply

Hardware Installation Guide for Cisco Catalyst Wireless Gateways
14
Overview
Power Supply

CHAPTER 2
Safety Guidelines and Warnings
•Statement 1071—Warning Definition, on page 15
•Statement 407—Japanese Safety Instruction, on page 16
•Statement 1004—Installation Instructions, on page 16
•Statement 1033—Safety Extra-Low Voltage (SELV)—IEC 60950/ES1–IEC 62368 DC Power Supply,
on page 16
•Statement 1047—Overheating Prevention, on page 16
•Statement 1074—Comply with Local and National Electrical Codes, on page 17
Statement 1071—Warning Definition
IMPORTANT SAFETY INSTRUCTIONS
Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Read the installation instructions before using, installing, or
connecting the system to the power source. Use the statement number provided at the end of each warning
statement to locate its translation in the translated safety warnings for this device.
SAVE THESE INSTRUCTIONS
Warning
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
15

Statement 407—Japanese Safety Instruction
You are strongly advised to read the safety instruction before using the product.
https://www.cisco.com/web/JP/techdoc/pldoc/pldoc.html
When installing the product, use the provided or designated connection cables/power cables/AC adapters.
Note
Statement 1004—Installation Instructions
Read the installation instructions before using, installing, or connecting the system to the power source.
Warning
Statement 1033—Safety Extra-Low Voltage (SELV)—IEC
60950/ES1–IEC 62368 DC Power Supply
To reduce risk of electric shock, connect the unit only to a DC power source that complies with the SELV
requirements in IEC 60950-based safety standards or ES1 requirements in IEC 62368-based safety standards.
Warning
Statement 1047—Overheating Prevention
To reduce the risk of fire or bodily injury, do not operate the unit in an area that exceeds the maximum
recommended ambient temperature of: 45℃.
Warning
Hardware Installation Guide for Cisco Catalyst Wireless Gateways
16
Safety Guidelines and Warnings
Statement 407—Japanese Safety Instruction