Cisco Blower Module 10000 ESR User manual

Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2000. Cisco Systems, Inc. All rights reserved. 78-10832-01
Cisco 10000 ESR
AC Power Entry Module Installation
This publication contains instructions for installing the AC Power Entry Module
(PEM) in the Cisco 10000 Edge Services Router (ESR). If you are not familiar
with the Cisco 10000 router, see the Cisco 10000 ESR System Description, and
the Cisco 10000 ESR Hardware Installation Guide for additional information.
Contents
The following sections are included in this configuration guide:
•Product Description, page 2
•Prerequisites and Preparation, page 3
•Installation Guidelines, page 4
•Adding or Replacing an AC PEM, page 5
•FCC Class A Compliance, page 20
•Cisco Connection Online, page 20
•Documentation CD-ROM, page 22

Product Description
2
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Product Description
The AC PEM provides power conversion directly from the facility VAC input
power (100 VAC to 240 VAC) to the –48V VDC used internally by the system (see
Figure 1). AC power is delivered to the AC PEM from the VAC connection power
cable to the power cord attached to the PEM.
Figure 1 AC PEM
There are two PEM bays in the chassis; however, you only need one PEM to power
the router. You can install an additional PEM for power redundancy.
30004
POWER
FAULT

3
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Prerequisites and Preparation
Prerequisites and Preparation
Before you perform any of the procedures in this guide, Cisco recommends that
you:
•Read the safety guidelines in the next section and review the electrical safety
and ESD-prevention guidelines in the Cisco 10000 ESR Hardware
Installation Guide.
•Ensure that you have all of the necessary tools and equipment before
beginning the installation (see the “Installation Guidelines” section on
page 4).
•Have access to the following documents (shipped with your Cisco 10000
system) during the installation:
– Cisco 10000 ESR System Description
– Cisco 10000 ESR Hardware Installation Guide
– Cisco 10000 ESR Troubleshooting Guide
– Cisco 10000 ESR Software Configuration Guide
Safety Guidelines
Before you begin the installation or replacement procedure, review the safety
guidelines in this section to avoid injuring yourself or damaging the equipment.
Before you install, configure, or perform maintenance on the router, you should
also review the safety warnings listed in the Cisco 10000 ESR Hardware
Installation Guide.
Safety Warnings
Safety warnings appear throughout this publication in procedures that, if
performed incorrectly, may harm you. A warning symbol precedes each warning
statement. The following warning is an example of a safety warning. It identifies
the warning symbol and associates it with a bodily injury hazard.

Installation Guidelines
4
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Warning This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment, be
aware of the hazards involved with electrical circuitry and be
familiar with standard practices for preventing accidents. To see
translations of the warnings that appear in this publication, refer
to the Regulatory Compliance and Safety Information document
that accompanied this device.
Note If you need translations of the safety warning, see the Cisco 10000
ESR Hardware Installation Guide.
Installation Guidelines
The Cisco 10000 system is hot-swappable, which means you can remove and
replace a defective PEM while the system is operating (assuming that your system
has a second AC PEM installed for redundancy). It is not necessary to notify the
software or reset the system power. This feature lets you add, remove, or replace
a second PEM while the system maintains all routing information and ensures
session preservation.
Required Tools and Equipment
You need the following tools and equipment to install an AC PEM:
•A Number 2 Phillips screwdriver
•3/16-inch flat-blade screwdriver
•An electrostatic discharge (ESD) preventive wrist or ankle strap with
connection cord

5
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Adding or Replacing an AC PEM
Adding or Replacing an AC PEM
This section describes how to add or replace an AC PEM in the Cisco 10000
chassis. It contains the following procedures:
•Removing the Front Cover, page 5
•Installing a Second AC PEM, page 7
•Replacing an AC PEM, page 12
•Troubleshooting the Installation, page 19
Removing the Front Cover
Use the following procedure to remove the front cover from the system. If your
system does not use a front cover, go to the “Installing a Second AC PEM” section
on page 7 or to the “Replacing an AC PEM” section on page 12.
Step 1 Unlock each bezel plug by inserting the tip of a flat-blade screwdriver between
the top and bottom sections of the plug, and then rotating the screwdriver to
unlock the top portion of the plug (Figure 2).
Repeat this procedure for all four bezel plugs and then remove the plugs.
Figure 2 Unlocking the Bezel Plugs
30038
POWER
FAULT
MISWIRE
POWER
FAULT
MISWIRE
FANSOK
FANFAILURE
MULTI-FANFAILURE
POWER
FAULT
MISWIRE
Cisco 10000
30039
POWER
FAULT
MISWIRE
POWER
FAULT
MISWIRE
FANSOK
FANFAILURE
MULTI-FANFAILURE
POWER
FAULT
MISWIRE
Cisco 10000

Adding or Replacing an AC PEM
6
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Step 2 Remove the cover by lifting it up slightly and then pulling it toward you
(Figure 3).
Figure 3 Removing the Front Cover
Step 3 Continue installing or replacing the AC PEM:
•If you are installing a second AC PEM, go to the “Installing a Second AC
PEM” section on page 7.
•If you are replacing an AC PEM, go to the “Replacing an AC PEM” section
on page 12.
30040
13
240A
PROCESSOR ONLY
0B 5678
PROCESSOR ONLY
POWER
FAULT
MISWIRE
POWER
FAULT
MISWIRE
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
FAIL
CAALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
FAIL
CAALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
FAIL
CAALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
FAIL
CAALARM
LOOP
C10000
6CT3
CISCO
10000
LINK
TX
RX
FAIL
GIGABIT ETHERNET
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
CH OC-12-DSO SM-IR
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
PERFORMANCE ROUTING ENGINE
ALARMS
CISCO
10000
ACTIVITY
LINK
CRITICAL
MAJOR
MINOR
ACO
SLOT0
STATUS
FAIL
BITS
P/N
ESR-PRE3
CONSOLE
ETHERNET
LINK
ACTIVITY
AUX
PERFORMANCE ROUTING ENGINE
ALARMS
CISCO
10000
ACTIVITY
LINK
CRITICAL
MAJOR
MINOR
ACO
SLOT0
STATUS
FAIL
BITS
P/N
ESR-PRE3
CONSOLE
ETHERNET
LINK
ACTIVITY
AUX
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
TX
RX
FAIL
OC–12/STM–4 POS SM–IR
FANS
OK
FAN
FAILURE
MULTI-
FAN
FAILURE
When hot swapping this fan tray,
removal and replacement must
be done in under two minutes or
system shutdown will occur.
CAUTION
FANS OK
FAN FAILURE
MULTI-FAN FAILURE
POWER
FAULT
MISWIRE
POWER
FAULT
MISWIRE
Cisco 10000

7
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Adding or Replacing an AC PEM
Installing a Second AC PEM
Use the following procedure to install a second AC PEM in the bottom power bay
for redundancy.
Step 1 Attach an antistatic wrist strap to your wrist and to an ESD socket on the chassis,
or to a bare metal surface on the chassis or frame (Figure 4).
Figure 4 ESD Chassis Connection
PROCESSOR ONLY
POWER
FAULT
MISWIRE
CISCO
10000
CH OC-12-DSO SM-IR
6XCT3–DS0
5
6XCT3–DS0
5
FAIL
PERFORMANCE ROUTING ENGINE
ST
A
TUS
ACO
CRITICAL
MINOR
MAJOR
FAIL
PERFORMANCE ROUTING ENGINE
ST
A
TUS
ACO
CRITICAL
MINOR
MAJOR
6XCT3–DS0
5
6XCT3–DS0
5
6XCT3–DS0
5
OC–12/STM–4 POS SM–IR
32236
ESD
socket

Adding or Replacing an AC PEM
8
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Step 2 Loosen the captive screws to remove the blank cover from the bottom power bay
(Figure 5).
Figure 5 Removing the Blank Cover
13
240A
PROCESSOR
PROCESSOR
FANS
OK
FAN
FAILURE
MULTI-
FAN
FAILURE
Whenhot swappingthis fantray,
removal andreplacement must
bedonein undertwominutesor
systemshutdownwill occur.
CAUTION
Captive
screws
POWER
FAULT
CISCO
10000
LINK
TX
RX
FAIL
GIGABIT ETHERNET
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
CH OC-12-DSO SM-IR
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
FAIL
CONSOLE
ST
A
TUS
ACO
CRITICAL
MINOR
MAJOR
ETHERNET
LINK
ACTIVITY
AUX
SLOT 0
SLOT 1
CISCO
10000
32692

9
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Adding or Replacing an AC PEM
Step 3 Install the new AC PEM all the way into the power bay to ensure a secure
connection to the backplane, and then tighten the captive screws (Figure 6).
Figure 6 Installing an AC PEM
13
240A
PROCESSOR
PROCESSOR
FANS
OK
FAN
FAILURE
MULTI-
FAN
FAILURE
Whenhot swappingthis fantray,
removal andreplacement must
bedonein under twominutesor
systemshutdownwill occur.
CAUTION
POWER
FAULT
POWER
FAULT
Captive
screws
32234
CISCO
10000
LINK
TX
RX
FAIL
GIGABIT ETHERNET
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
CH OC-12-DSO SM-IR
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
FAIL
CONSOLE
ST
A
TUS
ACO
CRITICAL
MINOR
MAJOR
ETHERNET
LINK
ACTIVITY
AUX
SLOT 0
SLOT 1
CISCO
10000

Adding or Replacing an AC PEM
10
Cisco 10000 ESR AC Power Entry Module Installation
78-10832-01
Step 4 Connect the power cord from the PEM to your power cord that connects to the
facility VAC input.
Step 5 Set the AC power cord connectors in a cord strain relief (canoe) to prevent them
from accidently disconnecting (Figure 7).
Figure 7 AC Power Cord Connectors in Canoes
Step 6 Plug the facility AC input power cord into a power receptacle.
32235
13
240A
PROCESSORONLY
0B 5678
PROCESSORONLY
POWER
FAULT
POWER
FAULT
CISCO
10000
LINK
TX
RX
FAIL
GIGABIT ETHERNET
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
CH OC-12-DSO SM-IR
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
FAIL
PERFORMANCE ROUTING ENGINE
CONSOLE
ST
A
TUS
ACO
CRITICAL
MINOR
MAJOR
ETHERNET
LINK
ACTIVITY
AUX
SLOT0
SLOT1
FAIL
PERFORMANCE ROUTING ENGINE
CONSOLE
ST
A
TUS
ACO
CRITICAL
MINOR
MAJOR
ETHERNET
LINK
ACTIVITY
AUX
SLOT0
SLOT1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
ALARM
LOOP
FAIL
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
CARRIER
TX
RX
FAIL
OC–12/STM–4 POS SM–IR
CISCO
10000
CISCO
10000
FANS
OK
FAN
FAILURE
MULTI-
FAN
FAILURE
When hot swapping this fan tray,
removal and replacement must
be done in under two minutes or
system shutdown will occur.
CAUTION
1