Cisco Digistar EoC User manual

DigiStar Ethernet over Coax End-Point E320.1
User Guide

2
Notice
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may
appear in this guide. Cisco reserves the right to change this guide at any time
without notice. No part of this document may be reproduced in any form
without the express written permission of Cisco Systems, Inc.
Trademark Acknowledgments
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco
and/or its affiliates in the U.S. and other countries. A listing of Cisco's
trademarks can be found at www.cisco.com/go/trademarks .
Third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between
Cisco and any other company. (1009R)
Notice for CATV Installers
If you are a CATV installer, read the information in the box below.

3
Important Safety Instructions
Protecting Against Power Surges
To protect the EP from power surge damage, ground (earth) your cable product
to provide some protection against voltage surges and built-up static charges.
To avoid these voltage surges caused by lightning storms and power outages,
plug the EP into a surge protector to reduce the risk of damage.
Heed Warnings
Adhere to all warnings on the product and in the operating instructions.
Read, Retain, and Follow These Instructions
Read instructions before you operate this unit. Follow all operating instructions
that accompany this product. Retain the instructions for future use. Give
particular attention to all safety precautions.
Comply With Warnings
Avoid electric shock. Comply with all warnings and cautions in the operating
instructions, as well as those that are affixed to this product.
Power Warnings
Providing a Power Source
A label on this product indicates the correct power source for this product.
Operate this product only from an electrical outlet with the voltage and
frequency indicated on the product label.
If you are uncertain of the type of power supply to your home or business,
consult your service provider or your local power company.
If this product is equipped with a two-prong (polarized) safety plug, follow
these safety guidelines to properly ground this product:
Grounding This Product (U.S.A, and Canada Only)
Avoid electric shock. Comply with all warnings and cautions in the operating
instructions, as well as those that are affixed to this product.
Continued on next page

4
Important Safety Instructions, Continued
WARNING: To avoid electric shock and fire hazard, match the plug
and outlet connections carefully, then fully insert. If the plug and outlet
do not match, or you can not fully insert the plug, contact an electrician to
update your power outlet.
For a 2-prong plug (a polarized plug with one wide blade and one narrow
blade), insert the plug into a polarized mains, 2-prong outlet in which one
socket is wider than the other.
Note: If you are unable to insert this plug fully into the outlet, try reversing the
plug. If the plug still fails to fit, contact your electrician to replace your outlet.
Overloading
WARNING: Avoid electric shock and fire hazard! Do not overload
main AC outlets and extension cords. For products that require battery
power or other power sources to operate them, refer to the operating
instructions for those products.
Do not overload electrical outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock. For products that
require battery power or other power sources to operate, refer to the operating
instructions for those products.
Preventing Power Cord Damage
Arrange all power cords so that people or pets can not walk on the cords. Do
not place objects on the cords. Do not lean objects against the cords. Placing
objects on or leaning objects against cords can damage the cords. Give particular
attention to cords at the point at which the cord connects to plugs, at the
electrical outlets, and where the cords exit the product.
Usage Warnings
Providing Ventilation
Continued on next page

5
Important Safety Instructions, Continued
This product has openings for ventilation that protect it from overheating. To
ensure the reliability of this product, do the following:
Do not block or cover these openings
Do not place entertainment devices (such as VCRs or DVDs), lamps, book,
vases with liquids, or other objects on top of this product.
Do not place this product in any of the following locations:
- On a bed, sofa, rug, or similar surface.
- Near heat sources such as radiators, heat registers, stoves, or other
products that produce heat.
- In an enclosure, such as a bookcase or rack, unless the installation
provides proper ventilation.
Selecting a Proper Location
WARNING: Avoid personal injury and damage to this product! An
unstable surface may cause this product to fall.
Place this product in a location that is close enough to an electrical outlet and
where the power cord is easily accessible to be disconnected from the wall
outlet or from the rear panel of the product.
Important: The power cord is the mains power supply disconnect device. Place
this product on a stable surface. The surface must support the size and weight
of this product.
Cleaning This Product
WARNING: Avoid electric shock! Unplug this product before
cleaning.
Before cleaning this product, unplug it from the electrical outlet. Use a damp
cloth to clean this product. Do not use a liquid cleaner or an aerosol cleaner. Do
not use a magnetic/static cleaning device (dust remover) to clean this product.
Continued on next page

6
Important Safety Instructions, Continued
Protecting This Product from Foreign Objects and Water or Moisture Damage
WARNING: Avoid electric shock and fire hazard! Never push objects
through the openings in this product. Foreign objects can cause electrical
shorts that can result in electric shock or fire. Do not expose this product
to rain or moisture. Do not place objects filled with liquid, such as vases,
on this product.
Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock.
Do not expose this product to liquids or moisture. Do not place this product on
a wet surface. Do not spill liquids on or near this product. Do not use this
product near water, such as a bath tub, wash bowl, sink, or laundry tub, in a
wet basement, or near a swimming pool.
Accessories Warnings
WARNING: Avoid any potential for electric shock or fire. Do not use
accessories with this product unless recommended by your cable service
provider.
Avoid any potential for electric shock or fire. Do not use accessories with this
product unless recommended by your cable service provider.
Service Warnings
Servicing This Product
WARNING: Avoid electric shock! Opening or removing the cover
may expose you to dangerous voltages. This product contains no
user-serviceable parts. Refer all servicing to qualified service personnel.
Continued on next page

7
Important Safety Instructions, Continued
Do not open the cover of this product. If you open the cover, your warranty will
be void. Refer all servicing to qualified personnel only. Contact your service
provider for instructions.
Obtaining Service for Product Damage
For damage that requires service, unplug this product from the AC outlet. Then
contact your cable service provider or qualified service personnel to obtain
service for the following conditions:
If there is damage to the power supply cord or plug
If liquid enters this product
If you expose this product to rain or water
If you drop this product, a heavy object falls on this product, or damage
occurs to the cover of this product
If this product does not operate normally by following the operating
instructions.
Checking Product Safety
Upon completion of any service or repairs to this product, the service technician
performs safety checks to determine that this product is in proper operating
condition.
Lightning
For added protection for this product during a lighting storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges. Plugging this product into a
surge protector may reduce the risk of damage.
Note: Unplugging this product for an extended period of time can result in loss
of authorization. For reauthorization, contact your cable service provider.
Continued on next page

8
Important Safety Instructions, Continued
Power Lines
WARNING: To avoid electric shock, do not locate an outside antenna
system in the vicinity of overhead power lines or power circuits.
Do not locate an outside antenna system in the vicinity of overhead power lines
or power circuits. When installing an outside antenna system, take extreme care
to keep from touching power lines or circuits, as contact might be fatal.
Electromagnetic Compatibility Regulatory Requirements
This equipment meets applicable electromagnetic compatibility (EMC)
regulatory requirements. Refer to this equipment’s data sheet for details about
regulatory compliance approvals. EMC performance is dependent upon the use
of correctly shielded cables of good quality for all external connections, except
the power source, when installing this equipment.
Ensure compliance with cable/connector specifications and associated
installation instructions where given elsewhere in this manual. Otherwise,
comply with the following good practices:
1. Multi-conductor cables should be of single-braided, shielded type and
have conductive connector bodies and backshells with cable clamps that
are conductively bonded to the backshell and capable of making 360°
connection to the cable shielding. Exceptions from this general rule will
be clearly stated in the connector description for the excepted connector
in question.
2. Ethernet cables should be of single-shielded or double-shielded type.
3. Coaxial cables should be of the double-braided shielded type.

9
Introduction
The DigiStar Ethernet over Coax (EoC) system is designed to combine a CATV
signal with Ethernet data for transmission to a subscriber’s home through the
existing coax access network.
With Ethernet data delivered to the building, the DigiStar EoC system meets the
IP interactive service requirement of cable operators for Multiple Dwelling Unit
(MDU) application. The DigiStar EoC system also supports Video-On-Demand
(VOD) upstream service requests in the IP data return path, and subscriber
service differentiation through rate limiting.
The EP is the end-point device of the DigiStar EoC system. It is located in a
subscriber’s home to provide CATV signal pass-through and Ethernet data to a
PC or IP set-top box. It complies with HPNA 3.1 (ITU-TG.9954) standards, and
provides high-speed and reliable data transmission.
Benefits and Features
Complies with HPNA 3.1 (ITU-T G.9954) standards
Complies with IEEE 802.1p CoS and 802.1q VLAN protocols
Auto synchronization and point-to-point communication with master device
Bidirectional data transmission band: 12–28 and 28–44 MHz
Adaptive FDQAM
CATV service band: 87–1000MHz
Supports MDI/MDIX on two 10/100Base-T ports
100 Mbps sustained rate
Supports SNMP based Element Management System (EMS)

10
What’s In the Carton?
Part Number List
What’s In the Carton?
After receiving the EP, check the equipment and accessories to verify that each
item is in the carton and that each item is undamaged. The carton contains the
following items:
One EP unit
220 VAC (50 Hz) power adapter with power cord
One CAT-5 Ethernet cable
One COAX cable (See the above part number list.)
One user guide
If you find any items missing or damaged, contact the customer services
department for assistance.
Part Number
Description
EEP3412210000000
DigiStar EOC EP E320.1, 44/54 MHz, 220 VAC, Ch-C, Metric
F-Type Connector, HPNA module
EEP3432210000000
DigiStar EOC EP E320.1, 44/54 MHz, 220 VAC, Ch-C,
Standard Connector, without COAX Cable, HPNA module
EEP3432220000000
DigiStar EOC EP E320.1, 44/54 MHz, 220 VAC, US-C,
Standard Connector, without COAX Cable, HPNA module